Lexus RX450h L (2022 year). Manual in english — page 24
399
6-3. Do-it-yourself maintenance
6
Mai
nte
na
nc
e a
nd
c
are
10
Install the cover.
11
Remove the protective tape.
■
Back-up lights (bulb type)
1
Open the back door and remove
the cover.
Using a flathead screwdriver, remove the
cover.
To prevent scratching to the vehicle, wrap
the tip of the flathead screwdriver with a
cloth, etc.
2
Turn the bulb base counterclock-
wise and remove it.
3
Remove the light bulb.
4
Install a new light bulb and then
install the bulb base to the light unit
by inserting it and turning it clock-
wise.
After installing the bulb base, wiggle it
lightly to make sure it is securely installed
and turn on the back-up lights to visually
check that there is no light leaking from
between the bulb base and light unit.
5
Install the cover.
Align the tabs of the cover with the grooves
and install the cover.
400
6-3. Do-it-yourself maintenance
WARNING
■
To prevent injury
Before performing any light bulb
replacement procedure, be sure to turn
the power switch off. Failure to do so may
result in burns from hot components or a
part of your body may get caught on an
operating component, possibly causing
serious injury.
■
Replacing light bulbs
●
Turn off the lights. Do not attempt to
replace the bulb immediately after
turning off the lights.
The bulbs become very hot and may
cause burns.
●
Do not touch the glass portion of the
light bulb with bare hands. When it is
unavoidable to hold the glass portion,
use and hold with a clean dry cloth to
avoid getting moisture and oils on the
bulb.
Also, if the bulb is scratched or
dropped, it may blow out or crack.
●
Fully install light bulbs and any parts
used to secure them. Failure to do so
may result in heat damage, fire, or
water entering the headlight unit. This
may damage the headlights or cause
condensation to build up on the lens.
●
Do not attempt to repair or disassem-
ble the light bulbs, connectors, electric
circuits or component parts.
Doing so may result in death or serious
injury due to electric shock.
■
To prevent damage or fire
●
Make sure bulbs are fully seated and
locked.
●
Check the wattage of the bulb before
installing to prevent heat damage.
401
7
7
When trouble
ari
ses
When trouble arises
.
7-1. Essential information
Emergency flashers. . . . ..
If your vehicle has to be stopped in
an emergency. . . . . . ..
If the vehicle is submerged or
water on the road is rising
. . . . . . . . . . . . . .
7-2. Steps to take in an emergency
If your vehicle needs to be towed
. . . . . . . . . . . . . .
If you think something is wrong
. . . . . . . . . . . . . .
If a warning light turns on or a
warning buzzer sounds . .
If a warning message is displayed
. . . . . . . . . . . . . .
If you have a flat tire. . . . ..
If the hybrid system will not start
. . . . . . . . . . . . . .
If you lose your keys. . . . .
If the fuel filler door cannot be
opened. . . . . . . . . .
If the electronic key does not
operate properly . . . . .
If the 12-volt battery is discharged
. . . . . . . . . . . . . . .
If your vehicle overheats . .
If the vehicle becomes stuck
. . . . . . . . . . . . . .
402
7-1. Essential information
7-1.Essential information
Press the switch.
All the turn signal lights will flash. To turn
them off, press the switch once again.
■
Emergency flashers
●
If the emergency flashers are used for a
long time while the hybrid system is not
operating (while the “READY” indicator
is not illuminated), the 12-volt battery may
discharge.
●
If any of the SRS airbags deploy (inflate)
or in the event of a strong rear impact, the
emergency flashers will turn on automati-
cally.
The emergency flashers will turn off auto-
matically after operating for approxi-
mately 20 minutes. To manually turn the
emergency flashers off, press the switch
twice.
(The emergency flashers may not turn on
automatically depending on the force of
the impact and conditions of the colli-
sion.)
1
Steadily step on the brake pedal
with both feet and firmly depress it.
Do not pump the brake pedal repeatedly
as this will increase the effort required to
slow the vehicle.
2
Shift the shift lever to N.
If the shift lever is shifted to N
3
After slowing down, stop the vehi-
cle in a safe place by the road.
4
Stop the hybrid system.
If the shift lever cannot be shifted to
N
3
Keep depressing the brake pedal
with both feet to reduce vehicle
speed as much as possible.
4
To stop the hybrid system, press
and hold the power switch for 2
consecutive seconds or more, or
Emergency flashers
The emergency flashers are used to
warn other drivers when the vehicle
has to be stopped on the road due
to a breakdown, etc.
Operating instructions
If your vehicle has to be
stopped in an emergency
Only in an emergency, such as if it
becomes impossible to stop the
vehicle in the normal way, stop the
vehicle using the following proce-
dure:
Stopping the vehicle
403
7-1. Essential information
7
W
he
n t
ro
ub
le
a
ris
es
press it briefly 3 times or more in
succession.
5
Stop the vehicle in a safe place by
the road.
If the door can be opened, open the
door and exit the vehicle.
If the door cannot be opened, open
the window using the power window
switch and ensure an escape route.
If the window can be opened, exit
the vehicle through the window.
If the door and window cannot be
opened due to the rising water,
remain calm, wait until the water
level inside the vehicle rises to the
point that the water pressure inside
of the vehicle equals the water pres-
sure outside of the vehicle and then
open the door after waiting for the
rising water to enter the vehicle, and
exit the vehicle. When the outside
water level exceeds half the height
of the door, the door cannot be
opened from the inside due to water
pressure.
■
Water level exceeds the floor
When the water level exceeds the floor and
time has passed, the electrical equipment
will get damaged, the power windows will
WARNING
■
If the hybrid system has to be turned
off while driving
Power assist for the steering wheel will
be lost, making the steering wheel
heavier to turn. Decelerate as much as
possible before turning off the hybrid sys-
tem.
If the vehicle is submerged
or water on the road is rising
This vehicle is not designed to be
able to drive on roads that are
deeply flooded with water. Do not
drive on roads where the roads may
be submerged or the water may be
rising. It is dangerous to remain in
the vehicle, if it anticipated that the
vehicle will be flooded or set a drift.
Remain calm and follow the follow-
ing.
404
7-1. Essential information
not operate, the engine and motor stop, and
the vehicle may not be able to get moving.
■
Using an emergency escape hammer
*1
Laminated glass
*2
is used in the windshield
and the windows on this vehicle. Laminated
glass cannot be shattered with an emer-
gency hammer
*1
.
*1
: Contact your Lexus dealer or aftermar-
ket accessory manufacturer for further
information about an emergency ham-
mer.
*2
: If equipped
■
How to distinguish laminated glass
When looking from the cross-sectional
view point, laminated glass is two sheets of
glass pasted together.
Laminated glass
Tempered glass
WARNING
■
Caution while driving
Do not drive on roads where the roads
may be submerged or the water may be
rising. Otherwise the vehicle may be
damaged and cannot move, as well as
become flooded and set a drift, which
may lead to death.
A
B
405
7-2. Steps to take in an emergency
7
W
he
n t
ro
ub
le
a
ris
es
7-2.Steps to take in an emergency
If your vehicle needs to be
towed
If towing is necessary, we recom-
mend having your vehicle towed by
your Lexus dealer or commercial
towing service, using a wheel-lift
type truck or flatbed truck.
Use a safety chain system for all
towing, and abide by all state/pro-
vincial and local laws.
If towing your vehicle with a
wheel-lift type truck, use a towing
dolly. (
WARNING
Observe the following precautions.Fail-
ure to do so may result in death or seri-
ous injury.
■
When towing the vehicle
Be sure to transport the vehicle with all
four wheels raised off the ground. If the
vehicle is towed with the tires contacting
the ground, the drivetrain or related
parts may be damaged, the vehicle may
fly off the truck, or electricity generated
by the operation of the motor may cause
a fire to occur depending on the nature
of the damage or malfunction.
■
While towing
●
When towing using cables or chains,
avoid sudden starts, etc. which place
excessive stress on the towing eyelets,
cables or chains. The towing eyelets,
cables or chains may become dam-
aged, broken debris may hit people,
and cause serious damage.
●
Do not turn the power switch off.
There is a possibility that the steering
wheel is locked and cannot be oper-
ated.
■
Installing towing eyelets to the vehi-
cle
Make sure that towing eyelets are
installed securely. If not securely
installed, towing eyelets may come loose
during towing.
406
7-2. Steps to take in an emergency
The following may indicate a problem
with your transmission. Contact your
Lexus dealer or commercial towing
service before towing.
The hybrid system warning message
is shown on the multi-information
display and the vehicle does not
move.
The vehicle makes an abnormal
sound.
From the front
Use a towing dolly under the rear
wheels.
From the rear
Use a towing dolly under the front
wheels.
NOTICE
■
To prevent damage to the vehicle
when towing using a wheel-lift type
truck
●
Do not tow the vehicle from the rear
when the power switch is off. The
steering lock mechanism is not strong
enough to hold the front wheels
straight.
●
When raising the vehicle, ensure ade-
quate ground clearance for towing at
the opposite end of the raised vehicle.
Without adequate clearance, the vehi-
cle could be damaged while being
towed.
■
To prevent damage to the vehicle
when towing with a sling-type truck
Do not tow with a sling-type truck, either
from the front or rear.
■
To prevent damage to the vehicle
during emergency towing
Do not secure cables or chains to the
suspension components.
■
Recreational towing (behind motor
home, etc.)
Never dinghy tow your vehicle to pre-
vent causing serious damage to the
Hybrid AWD system and transmission.
(
Situations when it is necessary to
contact dealers before towing
Towing with a wheel-lift type
truck
407
7-2. Steps to take in an emergency
7
W
he
n t
ro
ub
le
a
ris
es
When using a flat-bed truck to trans-
port the vehicle, use tire strapping
belts. Refer to the owner's manual of
the flat-bed truck for the tire strapping
method.
In order to suppress vehicle movement
during transportation, set the parking
brake and turn the power switch off.
If a tow truck is not available in an
emergency, your vehicle may be tem-
porarily towed using cables or chains
secured to the emergency towing eye-
lets. This should only be attempted on
hard surfaced roads for short distances
at under 18 mph (30 km/h).
A driver must be in the vehicle to steer
and operate the brakes. The vehicle’s
wheels, drive train, axles, steering and
brakes must be in good condition.
To have your vehicle towed by another
vehicle, the towing eyelet must be
installed to your vehicle. Install the tow-
ing eyelet using the following proce-
dure.
1
Take out the towing eyelet.
(
2
Remove the eyelet cover.
Except F SPORT models
F SPORT models
NOTICE
■
Towing with a sling-type truck
Do not tow with a sling-type truck to pre-
vent body damage.
Using a flatbed truck
Emergency towing (vehicles
with towing eyelets)
Emergency towing procedure
(vehicles with towing eyelets)
408
7-2. Steps to take in an emergency
3
Insert the towing eyelet into the
hole and tighten partially by hand.
4
Tighten down the towing eyelet
securely using a wheel nut wrench
or hard metal bar.
5
Securely attach cables or chains to
the towing eyelet.
Take care not to damage the vehicle body.
6
Enter the vehicle being towed and
start the hybrid system.
If the hybrid system does not start, turn the
power switch to ON mode.
7
Shift the shift lever to N and release
the parking brake.
Turn automatic mode off. (
When the shift lever cannot be shifted:
■
While towing
If the hybrid system is off, the power assist
for the brakes and steering will not function,
making steering and braking more difficult.
■
Wheel nut wrench
Wheel nut wrench is installed in luggage
compartment. (
409
7-2. Steps to take in an emergency
7
When trouble
ari
ses
Fluid leaks under the vehicle
(Water dripping from the air condi-
tioning after use is normal.)
Flat-looking tires or uneven tire
wear
Engine coolant temperature gauge
needle continually points higher
than normal
Changes in exhaust sound
Excessive tire squeal when corner-
ing
Strange noises related to the sus-
pension system
Pinging or other noises related to
the hybrid system
Engine missing, stumbling or run-
ning roughly
Appreciable loss of power
Vehicle pulls heavily to one side
when braking
Vehicle pulls heavily to one side
when driving on a level road
Loss of brake effectiveness, spongy
feeling, pedal almost touches the
floor
If you think something is
wrong
If you notice any of the following
symptoms, your vehicle probably
needs adjustment or repair. Con-
tact your Lexus dealer as soon as
possible.
Visible symptoms
Audible symptoms
Operational symptoms
410
7-2. Steps to take in an emergency
■
Brake system warning light
■
Brake system warning light
■
High coolant temperature warning light
*
(warning buzzer)
*
: This light illuminates on the multi-information display.
If a warning light turns on or a warning buzzer sounds
Calmly perform the following actions if any of the warning lights comes on or
flashes. If a light comes on or flashes, but then goes off, this does not necessar-
ily indicate a malfunction in the system. However, if this continues to occur,
have the vehicle inspected by your Lexus dealer.
Actions to the warning lights or warning buzzers
Warning light
Details/Actions
(U.S.A.)
or
(red)
(Canada)
Indicates that:
The brake fluid level is low; or
The brake system is malfunctioning
Immediately stop the vehicle in a safe place and contact your Lexus
dealer. Continuing to drive the vehicle may be dangerous.
Warning light
Details/Actions
(yellow)
Indicates a malfunction in:
The regenerative braking system;
The electronically controlled brake system; or
The electric parking brake
Have the vehicle inspected by your Lexus dealer immediately.
Warning light
Details/Actions
Indicates that the engine coolant temperature is too high
Immediately stop the vehicle in a safe place.
Handling method (
411
7-2. Steps to take in an emergency
7
When trouble
ari
ses
■
Hybrid system overheat warning light
*
(warning buzzer)
*
: This light illuminates on the multi-information display.
■
Charging system warning light
*
*
: Except F SPORT models: This light illuminates on the multi-information display.
F SPORT models: This light illuminates on the meter.
■
Low engine oil pressure warning light
*
(warning buzzer)
*
: This light illuminates on the multi-information display.
■
Malfunction indicator lamp
Warning light
Details/Actions
Indicates the hybrid system has overheated
Stop the vehicle in a safe place.
Handling method (
Warning light
Details/Actions
Indicates a malfunction in the vehicle’s charging system
Immediately stop the vehicle in a safe place and contact your Lexus
dealer. Continuing to drive the vehicle may be dangerous.
Warning light
Details/Actions
Indicates that the engine oil pressure is too low
Immediately stop the vehicle in a safe place and contact your Lexus
dealer.
Warning light
Details/Actions
(U.S.A.)
or
(Canada)
Indicates a malfunction in:
The hybrid system;
The electronic engine control system; or
The electronic throttle control system;
Have the vehicle inspected by your Lexus dealer immediately.
412
7-2. Steps to take in an emergency
■
SRS warning light
■
ABS warning light
■
Brake Override System warning light/Drive-Start Control warning light
*
(warning buzzer)
*
: This light illuminates on the multi-information display.
Warning light
Details/Actions
Indicates a malfunction in:
The SRS airbag system;
The front passenger occupant classification system; or
The seat belt pretensioner system
Have the vehicle inspected by your Lexus dealer immediately.
Warning light
Details/Actions
(U.S.A.)
or
(Canada)
Indicates a malfunction in:
The ABS; or
The brake assist system
Have the vehicle inspected by your Lexus dealer immediately.
Warning light
Details/Actions
When a buzzer sounds:
Brake Override System is malfunctioning;
Drive-Start Control is operating;
Drive-Start Control is malfunctioning; or
PKSB (Parking Support Brake) (if equipped) is operating
Follow the instructions displayed on the multi-information display.
When a buzzer does not sound:
Brake Override System is operating
Release the accelerator pedal and depress the brake pedal.
413
7-2. Steps to take in an emergency
7
When trouble
ari
ses
■
Electric power steering system warning light (warning buzzer)
■
Low fuel level warning light
■
Driver’s and front passenger’s seat belt reminder light (warning buzzer)
*
*
: Driver’s seat belt warning buzzer:
The driver’s seat belt warning buzzer sounds to alert the driver that his or her seat belt is not
fastened. Once the power switch is turned to ON mode, the buzzer sounds. If the seat belt
is still unfastened, the buzzer sounds intermittently for a certain period of time after the
vehicle reaches a certain speed.
Front passenger’s seat belt warning buzzer:
The front passenger’s seat belt warning buzzer sounds to alert the front passenger that his
or her seat belt is not fastened. If the seat belt is unfastened, the buzzer sounds intermit-
tently for a certain period of time after the vehicle reaches a certain speed.
Warning light
Details/Actions
(red)
or
(yellow)
Indicates a malfunction in the EPS (Electric Power Steering) system
Have the vehicle inspected by your Lexus dealer immediately.
Warning light
Details/Actions
Indicates that remaining fuel is approximately 2.9 gal. (11.0 L, 2.4 Imp.
gal.) or less
Refuel the vehicle.
Warning light
Details/Actions
Warns the driver and/or front passenger to fasten their seat belts
Fasten the seat belt.
If the front passenger’s seat is occupied, the front passenger’s seat
belt also needs to be fastened to make the warning light (warning
buzzer) turn off.
414
7-2. Steps to take in an emergency
■
Rear passengers’ seat belt reminder light
*1
(warning buzzer)
*2
*1
: This light illuminates on the center panel.
Regardless of whether or not a rear passenger is present, if the power switch is turned to
ON mode with the rear seat belts unfastened, this light will also illuminate for a certain
period of time.
*2
: Rear passengers’ seat belt warning buzzer:
The rear passengers’ seat belt warning buzzer sounds to alert the rear passenger that his or
her seat belt is not fastened. If the seat belt is unfastened, the buzzer sounds intermittently
for a certain period of time, after the seat belt is fastened and unfastened and the vehicle
reaches a certain speed.
■
Tire pressure warning light
■
LTA indicator (warning buzzer)
Warning light
Details/Actions
(RX450h)
or
(RX450hL)
Warns the rear passengers to fasten their seat belts
Fasten the seat belt.
Warning light
Details/Actions
Indicates the following:
Low tire pressure due to flat tire;
Low tire pressure due to natural causes; or
The tire pressure warning system is malfunctioning
Immediately stop the vehicle in a safe place.
Handling method (
Warning light
Details/Actions
(orange)
Indicates a malfunction in the LTA (Lane Tracing Assist)
Follow the instructions displayed on the multi-information display.
(
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст