Lexus LS400 (2000 year). Manual — part 83
A01891
A
B
A01866
A01865
A01867
EM–26
–
ENGINE MECHANICAL
TIMING BELT
1208
20.
INSTALL FAN BRACKET
Install the fan bracket with the 2 bolts and 2 nuts.
Torque:
12 mm head: 16 N·m (160 kgf·cm, 12 ft·lbf)
14 mm head: 32 N·m (330 kgf·cm, 24 ft·lbf)
HINT:
Each bolt length is indicated in the illustration.
Bolt Length:
106 mm (4.17 in.) for 12 mm head (A)
114 mm (4.49 in.) for 14 mm head (B)
21.
INSTALL A/C COMPRESSOR (See page
)
22.
INSTALL NO.2 TIMING BELT COVER
Install the No.2 timing belt cover with the 2 bolts.
Torque: 16 N·m (160 kgf·cm, 12 ft·lbf)
23.
INSTALL RH NO.3 TIMING BELT COVER
(a)
Install the gasket to the timing belt cover.
(b)
Fit the timing belt cover, matching it with the fan bracket.
(c)
Install the timing belt cover with the 3 bolts.
Torque: 7.5 N·m (80 kgf·cm, 66 in.·lbf)
(d)
Install the radiator reservoir outlet pipe to the RH cylinder
head and timing belt cover with the bolt and nut.
Torque: 7.5 N·m (80 kgf·cm, 66 in.·lbf)
(e)
Connect the outlet hose to the water inlet housing.
(f)
Connect the wire clamp.
(g)
Connect the PS air hose to the clamp of the timing belt
cover.
24.
INSTALL LH NO.3 TIMING BELT COVER
(a)
Install the gasket to the timing belt cover.
(b)
Run the camshaft position sensor wire through the timing
belt cover hole.
(c)
Fit the timing belt cover, matching it with the fan bracket.
(d)
Install the timing belt cover with the 4 bolts and nut.
Torque: 7.5 N·m (80 kgf·cm, 66 in.·lbf)
(e)
Install the wire grommet to the timing belt cover.
(f)
Install the sensor connector to the connector bracket.
(g)
Connect the sensor connector.
A02247
–
ENGINE MECHANICAL
TIMING BELT
EM–27
1209
(h)
Install the sensor wire to the wire clamp on the timing belt
cover.
(i)
Install the engine wire to the 2 wire clamps on the timing
belt cover.
25.
INSTALL DRIVE BELT IDLER PULLEY
Install the idler pulley and cover plate with the bolt.
Torque: 37 N·m (380 kgf·cm, 27 ft·lbf)
26.
INSTALL RADIATOR ASSEMBLY (See page
27.
INSTALL FAN PULLEY, FAN, FLUID COUPLING
AND DRIVE BELT
(a)
Temporarily install the fan pulley, the fan, fluid coupling
assembly with the 4 nuts.
(b)
Install the generator drive belt. (See page
)
(c)
Tighten the 4 nuts holding the fluid coupling to the fan
bracket.
Torque: 21 N·m (215 kgf·cm, 16 ft·lbf)
28.
INSTALL AIR CLEANER AND INTAKE AIR CONNEC-
TOR ASSEMBLY
29.
INSTALL V–BANK COVER
30.
FILL WITH ENGINE COOLANT
31.
START ENGINE AND CHECK FOR LEAKS
32.
RECHECK ENGINE COOLANT LEVEL
33.
INSTALL AIR CLEANER INLET
34.
INSTALL BATTERY CLAMP COVER
35.
INSTALL ENGINE UNDER COVER
36.
INSTALL OIL PAN PROTECTOR
EM09P–02
A02232
Fan and Fluid
Coupling Assembly
Fan Pulley
V–Bank Cover
ECT Switch Connector
for A/C Cooling Fan
Radiator Assembly
Upper Radiator Support
Battery Clamp Cover
Clip
Air Cleaner Inlet
EVAP Hose
PCV Hose
PS Air Hose
MAF Meter Connector
Air Cleaner and Intake
Air Connector Assembly
x 11
x 7
x 8
Oil Pan Protector
Engine Under Cover
Ground Cable
Wire Bracket
A/C Compressor
Generator Drive Belt
A/T Oil Cooler Hose
Lower Radiator Support
A/C Compressor Connector
A/C Compressor Stay
49 (500, 36)
N·m (kgf·cm, ft·lbf)
: Specified Torque
EM–28
–
ENGINE MECHANICAL
CYLINDER HEAD
1210
CYLINDER HEAD
COMPONENTS
A02841
PS Pump
Accelerator cable
RH Heat Insulator
for RH TWC
Front Exhaust Pipe
Pipe Support
Bracket
TWC
Gasket
RH Heat Insulator
for Front Side of
Front Exhaust Pipe
Gasket
Gasket
RH Heat Insulator
for RH TWC
LH Heat Insulator
for Front Side of
Front Exhaust Pipe
O–Ring
Oil Dipstick and
Guide for A/T
Non–reusable part
61.8 (630, 46)
43.1 (440, 32)
61.8 (630, 46)
43.1 (440, 32)
N·m (kgf·cm, ft·lbf): Specified Torque
–
ENGINE MECHANICAL
CYLINDER HEAD
EM–29
1211
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст