Lexus LS400 (2000 year). Manual — part 8
I03437
OFF
ON
1
4
I03442
Wire Harness Side
I03481
3
6
BE–114
–
BODY ELECTRICAL
ELECTRIC TENSION REDUCER SYSTEM
1977
3.
INSPECT BUCKLE SWITCH CONTINUITY
(a)
Check that there is continuity between terminal 1 and 4
on the switch side connector with the switch ON (belt fas-
tened).
(b)
Check that there is no continuity between terminal 1 and
4 on the switch side connector with the switch OFF (belt
unfastened).
If operation is not as specified, replace the seat belt inner.
4.
INSPECT BUCKLE SWITCH CIRCUIT
Disconnect the connector from the switch and inspect the con-
nector on wire harness side, as shown.
Tester connection
Condition
Specified condition
4 – Ground
Constant
Continuity
1 – Ground
Ignition switch ON
Battery positive voltage
1 – Ground
Ignition switch ACC or LOCK
No voltage
If the circuit is not as specified, inspect the circuits connected
to other parts.
5.
INSPECT BUCKLE SWITCH INDICATOR LIGHT OP-
ERATION
Connect the positive (+) lead from the battery to terminal 3 and
the negative (–) lead to terminal 6, and check that the indicator
light does not light up, replace the switch.
BE0C7–01
I03407
Engine Room Junction Block
MIR–HTR Fuse
Defogger Relay
A/C Control Panel Assembly
A/C Control Panel
A/C Amplifier
Instrument Panel
Junction Block
HEATER Fuse
Ignition Switch
RH Mirror
Mirror Defogger
LH Mirror
Mirror Defogger
Rear Window Glass
Window Defogger
–
BODY ELECTRICAL
DEFOGGER SYSTEM
BE–115
1978
DEFOGGER SYSTEM
LOCATION
BE0C8–03
I12823
Connector ”A”
Connector ”B”
22
1
6
2
I12824
ON
Connector ”A”
Connector ”B”
22
1
6
2
N13355
A/C Control Panel Side
N13356
A/C Control Panel Side
BE–116
–
BODY ELECTRICAL
DEFOGGER SYSTEM
1979
INSPECTION
1.
A/C control panel assembly:
INSPECT DEFOGGER SWITCH OPERATION
(a)
Connect the positive (+) lead from the battery to terminal
A1,A2 and negative (–) lead to terminal A22.
(b)
Connect the positive (+) lead from the battery to terminal
B6 through a 1.4 W test bulb.
(c)
Turn the defogger switch ON and check that the test bulb
and indicator light turn ON, then turn OFF after about 15
minutes.
If operation is not as specified, proceed to the next inspection.
2.
A/C control panel:
INSPECT DEFOGGER SWITCH INDICATOR
(a)
Separate control panel and A/C amplifier.
(b)
Connect the positive (+) lead from the battery to terminal
100 and the negative (–) lead to terminal 116.
(c)
Push the switch and check that the indicator light lights
up.
If operation is not as specified, replace the bulb.
3.
INSPECT DEFOGGER SWITCH CONTINUITY
Condition
Tester connection
Specified condition
OFF
–
No continuity
ON
95 – 105
Continuity
If operation is as specified, replace the A/C amplifier.
If continuity is not as specified, replace the control panel.
N13357
Wire Harness Side
Z08903
Z08810
Tester Probe
Tin Foil
Heat Wire
–
BODY ELECTRICAL
DEFOGGER SYSTEM
BE–117
1980
4.
INSPECT DEFOGGER SWITCH CIRCUIT
Disconnect the connector from the switch and inspect the con-
nector on wire harness side, as shown.
Tester connection
Condition
Specified condition
11 – Ground
Constant
Continuity
2 – Ground
Ignition switch ON
Battery positive voltage
2 – Ground
Ignition switch ACC or LOCK
No voltage
If the circuit is not as specified, inspect the circuits connected
to other parts.
5.
INSPECT DEFOGGER RELAY CONTINUITY
Condition
Tester connection
Specified condition
Constant
3 – 4
Continuity
Apply B+ between
terminals 3 and 4.
1 – 2
Continuity
If continuity is not as specified, replace the relay.
6.
INSPECT DEFOGGER WIRES
NOTICE:
When cleaning the glass, use a soft, dry cloth, and wipe the
glass in the direction of the wire. Take care not to damage
wires. Do not use detergents or glass cleaners with abra-
sive ingredients. When measuring voltage, wind a piece of
tin foil around the top of the negative probe and press the
foil against the wire with your fingers, as shown.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст