Lexus LS400 (2000 year). Manual — part 38
I03484
Wire Harness Side
–
BODY ELECTRICAL
AUDIO SYSTEM
BE–229
2092
Tester connection
Condition
Specified condition
B7 – Ground
Constant
Continuity
B4 – Ground
Constant
Battery positive voltage
C12 – Ground
Ignition switch position ACC or ON
Battery positive voltage
If circuit is not as specified, inspect the circuits connected to oth-
er parts.
6.
Pioneer made and LEXUS navigation system:
INSPECT CD AUTO CHANGER CIRCUIT
Disconnect the connectors from the controller and inspect the
connector on the wire harness side, as shown.
Tester connection to
terminal number
Condition
Specified condition
5 – Ground
Constant
Battery positive voltage
12 – Ground
Ignition switch LOCK
No voltage
12 – Ground
Ignition switch ACC or ON
Battery positive voltage
If circuit is not as specified, inspect the circuits connected to oth-
er parts.
HINT:
Since the signals to and from the AP+, AP–, SGND, GND1 ter-
minals are serial signals, they cannot ordinarily be measured
with a tester.
I03485
Wire Harness Side
Connector ”A”
Connector ”B”
Connector ”C”
BE–230
–
BODY ELECTRICAL
AUDIO SYSTEM
2093
7.
LEXUS navigation system:
INSPECT RADIO RECEIVER ASSEMBLY CIRCUIT
Disconnect the connectors from the radio receiver assembly.
And inspect the connector on the wire harness side, as shown.
Tester connection
Condition
Specified condition
B2 – Ground
Constant
Continuity
B1 – Ground
Ignition switch position ACC or ON
Battery positive voltage
B1 – Ground
Ignition switch position LOCK
No voltage
B4 – Ground
Constant
Battery positive voltage
If circuit is not as specified, inspect the circuits connected to oth-
er parts.
HINT:
Check the wire harness between power amplifier and the CD
auto changer, between radio receiver assembly and power am-
plifier.
8.
INSPECT GLASS PRINTED ANTENNA
(Use same procedure as for ”INSPECT DEFOGGER WIRES”
on page
9.
REPAIR GLASS PRINTED ANTENNA
(Use same procedure as for ”REPAIR DEFOGGER WIRES” on
page
)
BE0B8–01
Z14947
–
BODY ELECTRICAL
POWER SOURCE
BE–23
1886
INSPECTION
1.
INSPECT INSTRUMENT PANEL JUNCTION BLOCK
BE–24
–
BODY ELECTRICAL
POWER SOURCE
1887
2.
FUSE CIRCUIT
Remove the fuse from the junction block and inspect the con-
nector on junction block side.
Connect numbers are shown in the illustration.
Fuse
Tester connection
Condition
Specified condition
PANEL
3 – Ground
Light control switch TAIL or HEAD
Battery positive voltage
A/C
5 – Ground
Constant
Battery positive voltage
ECU–IG
10 – Ground
Ignition switch ON
Battery positive voltage
TURN
12 – Ground
Ignition switch ON
Battery positive voltage
WASHER
14 – Ground
Ignition switch ON
Battery positive voltage
ST
15 – Ground
Ignition switch START
Battery positive voltage
P RR DOOR
18 – Ground
Constant
Battery positive voltage
FUEL OPN
20 – Ground
Constant
Battery positive voltage
PWR–IG
21 – Ground
Ignition switch ON
Battery positive voltage
WIPER
24 – Ground
Ignition switch ON
Battery positive voltage
AIR SUS
25 – Ground
Ignition switch ON
Battery positive voltage
TAIL
27 – Ground
Light control switch TAIL or HEAD
Battery positive voltage
STOP
29 – Ground
Constant
Battery positive voltage
RR CIG
32 – Ground
Ignition switch ACC or ON
Battery positive voltage
GAUGE
33 – Ground
Ignition switch ON
Battery positive voltage
HEATER
35 – Ground
Ignition switch ON
Battery positive voltage
D RR DOOR
38 – Ground
Constant
Battery positive voltage
STOP–S
39 – Ground
Stop light switch ON
Battery positive voltage
RADIO No.2
42 – Ground
Ignition switch ACC or ON
Battery positive voltage
FR CIG
44 – Ground
Ignition switch ACC or ON
Battery positive voltage
IGN
46 – Ground
Ignition switch ON
Battery positive voltage
FR FOG
47 – Ground
Constant
Battery positive voltage
SEAT FR H
49 – Ground
Constant
Battery positive voltage
PWR H
51 – Ground
Constant
Battery positive voltage
If the circuit is not as specified, inspect the circuit connected to
other parts.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст