Lexus UX250h (2023 year). Manual in english — page 7
122
3-2. Opening, closing and locking the doors
sides of the power back door. When the
door is automatically closing and the sen-
sors are pushed due to an object being
clamped, etc., the jam protection function
operates.
From that position the door automatically
moves a little in the opposite direction and
then the function stops.
■
If the back door opener is inoperative
The back door can be unlocked from the
inside.
1
Remove the cover.
To protect the cover, place a rag between
the flathead screwdriver and the cover as
shown in the illustration.
2
Move the lever.
■
Customization
Some functions can be customized. (Cus-
tomizable features:
P.430)
WARNING
■
Back door closer
●
In the event that the back door is left
slightly open, the back door closer will
automatically close it to the fully closed
position. It takes several seconds
before the back door closer begins to
operate. Be careful not to catch fingers
or anything else in the back door, as
this may cause bone fractures or other
serious injuries.
●
Be careful not to catch fingers or any-
thing else when using the back door
closer as it still operates when the
power back door system is canceled.
■
Power back door
Observe the following precautions when
operating the power back door.
Failure to do so may cause death or seri-
ous injury.
●
Check the safety of the surrounding
area to make sure there are no obsta-
cles or anything that could cause any
of your belongings to get caught.
●
If anyone is in the vicinity, make sure
they are safe and let them know that
the back door is about to open or
close.
●
If the power back door system is dis-
abled, while the back door is operating
automatically, the automatic opera-
tion is stopped. The back door then
has to be operated manually. Take
extra care in this situation, as the back
door may open or close suddenly.
123
3-2. Opening, closing and locking the doors
3
Before drivi
ng
WARNING
●
If the operating conditions of the
power back door (
P.119) are no lon-
ger met, a buzzer may sound and the
back door may stop opening or clos-
ing. The back door then has to be
operated manually. Take extra care
when on an incline, as the back door
may open or close abruptly.
●
On an incline, the back door may sud-
denly shut after it opens. Make sure
the back door is fully open and secure.
●
In the following situations, the power
back door may detect an abnormality
and automatic operation may be
stopped. In this case, the back door
has to be operated manually. Take
extra care in this situation, as the back
door may open or close suddenly.
• When the back door contacts an
obstacle
• When the 12-volt battery voltage sud-
denly drops, such as when the power
switch is turned to ON or the hybrid
system is started during automatic
operation
●
If a bicycle carrier or similar heavy
object is attached to the back door, the
power back door may not operate,
causing itself to malfunction, or the
back door may suddenly shut again
after being opened, causing some-
one’s hands, arms, head or neck to be
caught and injured. When installing an
accessory part to the back door, using
a genuine Lexus part is recommended.
■
Jam protection function
Observe the following precautions.
Failure to do so may cause death or seri-
ous injury.
●
Never use any part of your body to
intentionally activate the jam protec-
tion function.
●
The jam protection function may not
work if something gets caught just
before the back door fully closes. Be
careful not to get fingers caught or
anything else.
●
The jam protection function may not
work depending on the shape of the
object that is caught. Be careful not to
catch fingers or anything else.
■
Hands Free Power Back Door
Observe the following precautions.
Failure to do so may cause death or seri-
ous injury.
●
Check the safety of the surrounding
area to make sure there are no obsta-
cles or anything that could cause any
of your belongings to get caught.
●
Exhaust gases cause the exhaust pipes
to become quite hot. When operating
the Hands Free Power Back Door, be
careful not to touch the exhaust pipe.
●
Do not operate the Hands Free Power
Back Door if there is little space under
the rear bumper.
NOTICE
■
Back door spindles
The back door is equipped with spindles
that hold the back door in place.
Observe the following precautions.
Failure to do so may cause damage to
the back door spindle
, resulting in
malfunction.
●
Do not attach any foreign objects,
such as stickers, plastic sheets, or
adhesives to the spindle rod.
A
A
124
3-2. Opening, closing and locking the doors
NOTICE
●
Do not touch the spindle rod with
gloves or other fabric items.
●
Do not attach any accessories other
than genuine Lexus parts to the power
back door.
●
Do not place your hand on the spindle
or apply lateral forces to it.
■
To prevent back door closer malfunc-
tion
Do not apply excessive force to the back
door while the back door closer is oper-
ating. Applying excessive force may
cause the back door closer to malfunc-
tion.
■
To prevent damage to the power
back door
●
Make sure that there is no ice between
the back door and frame that would
prevent movement of the back door.
Operating the power back door when
excessive load is present on the back
door may cause a malfunction.
●
Do not apply excessive force to the
back door while the power back door
is operating.
●
Take care not to damage the sensors
(installed on the right and left edges of
the power back door) (
P.121) with a
knife or other sharp object. If the sen-
sor is disconnected, the power back
door will not close automatically.
■
Close & lock function
When closing the power back door
using the close & lock function, a differ-
ent buzzer than the normal one will
sound before the operation begins.
To check that the operation has started
correctly, check that a different buzzer
than the normal one has sounded.
Additionally, when the power back door
is fully closed and locked, operation sig-
nals will indicate that all of the doors have
been locked.
Before leaving the vehicle, make sure
that the operation signals have operated
and that all of the doors are locked.
■
Hands Free Power Back Door pre-
cautions
Observe the following to ensure that the
power back door function operates
properly:
●
Do not apply coatings that have a rain
clearing (hydrophilic) effect, or other
coatings, to the lower center part of
the rear bumper.
●
Do not subject the rear bumper to a
strong impact.
If the rear bumper has been subjected
to a strong impact, the Hands Free
Power Back Door may not operate
properly. If the Hands Free Power
Back Door does not operate in the fol-
lowing situations, have the vehicle
inspected by your Lexus dealer.
• The kick sensor or its surrounding area
has been subjected to a strong impact.
• The lower center part of the rear
bumper is scratched or damaged.
●
Do not disassemble the rear bumper.
●
Do not attach stickers to the rear
bumper.
●
Do not paint the rear bumper.
125
3-2. Opening, closing and locking the doors
3
Before drivi
ng
The power back door system can be
enabled/disabled on the multi-infor-
mation display. (
P.89)
1
Press
or
of the meter con-
trol switches and select
.
2
Press
or
of the meter con-
trol switches, select the “Vehicle
Settings” and then press “OK”.
3
Press
or
of the meter con-
trol switches, select
and
then press “OK”.
4
Press
or
of the meter con-
trol switches, and then select “Sys-
tem Settings”.
5
ON and OFF will be switched
when “OK” is pressed.
If the power back door is disabled, it will
remain disabled unless it is enabled on the
multi-information display. (It will not be
enabled even when the power switch is
turned off and then back to ON.)
The Hands Free Power Back Door
(kick sensor) can be enabled/disabled
on the multi-information display.
(
P.89)
1
Press
or
of the meter con-
trol switches and select
.
2
Press
or
of the meter con-
trol switches, select the “Vehicle
Settings” and then press “OK”.
3
Press
or
of the meter con-
trol switches, select
, and
then press “OK”.
4
Press
or
of the meter con-
trol switches, and then select
“KICK SENSOR”.
5
ON and OFF will be switched
when “OK” is pressed.
If the Hands Free Power Back Door is dis-
abled, it will remain disabled unless it is
enabled on the multi-information display.
(It will not be enabled even when the
power switch is turned off and then back to
ON.)
The open position of the power back
door can be adjusted.
1
Stop the back door in the desirable
position. (
P.117)
2
Press and hold the power back
door switch on the back door for 2
seconds.
• When the settings are completed,
the buzzer sounds 4 times.
• When opening the back door the
next time, the back door will stop at
Canceling the power back door
system (vehicles with power
back door)
Canceling the Hands Free
Power Back Door (vehicles with
power back door)
Adjusting the open position of
the back door (vehicles with
power back door)
126
3-2. Opening, closing and locking the doors
that position.
■
Returning the back door automatic stop
position to the initial settings
Press and hold the power back door switch
on the back door for 7 seconds.
After the buzzer sounds 4 times, it sounds
twice more. When the power back door
does the opening operation the next time,
the door will open to the initial settings posi-
tion.
■
Antenna location
Antennas outside the cabin
Antennas inside the cabin
Antenna inside the luggage compart-
ment
Antenna outside the luggage compart-
ment
Smart access system with
push-button start
The following operations can be
performed simply by carrying the
electronic key (including the card
key) on your person, for example in
your pocket. The driver should
always carry the electronic key.
Locks and unlocks the doors
(
P.110)
Locks and unlocks the back door
(
P.114)
Starts the hybrid system
(
P.163)
A
B
C
D
127
3-2. Opening, closing and locking the doors
3
Before drivi
ng
■
Effective range (areas within which the
electronic key is detected)
When locking or unlocking the doors
The system can be operated when the elec-
tronic key is within about 2.3 ft. (0.7 m) of
an outside front door handle. (Only the
doors detecting the key can be operated.)
When starting the hybrid system or
changing power switch modes
The system can be operated when the elec-
tronic key is inside the vehicle.
■
If an alarm sounds or a warning message
is displayed
An alarm sounds and warning messages
are displayed on the multi-information dis-
play to protect against unexpected acci-
dents or theft of the vehicle resulting from
erroneous operation. When a warning
message is displayed, take appropriate
measures based on the displayed message.
When only an alarm sounds, circumstances
and correction procedures are as follows.
●
When an exterior alarm sounds once for
5 seconds
●
When an Interior alarm pings repeatedly
■
If “Key Detected in Vehicle” is shown on
the multi-information display
An attempt was made to lock the doors
using the smart access system with push-
button start while the electronic key was still
inside the vehicle. Retrieve the electronic
key from the vehicle and lock the doors
again.
■
Battery-saving function
The battery-saving function will be acti-
vated in order to prevent the electronic key
battery and the 12-volt battery from being
discharged while the vehicle is not in opera-
tion for a long time.
●
In the following situations, the smart
access system with push-button start may
take some time to unlock the doors.
• The electronic key has been left in an
area of approximately 6 ft. (2 m) of the
outside of the vehicle for 10 minutes or
longer.
• The smart access system with push-but-
ton start has not been used for 5 days or
longer.
●
If the smart access system with push-but-
ton start has not been used for 14 days or
longer, the doors cannot be unlocked at
any doors except the driver’s door. In this
case, take hold of the driver’s door han-
dle, or use the wireless remote control or
the mechanical key, to unlock the doors.
Situation
Correction proce-
dure
An attempt was
made to lock the
vehicle while a door
was open.
Close all of the
doors and lock the
doors again.
A
B
Situation
Correction proce-
dure
The power switch
was turned to ACC
while the driver’s
door was open (The
driver’s door was
opened when the
power switch was in
ACC).
Turn the power
switch off and close
the driver’s door.
The power switch
was turned off while
the driver’s door was
open.
Close the driver’s
door.
128
3-2. Opening, closing and locking the doors
■
Turning an electronic key to battery-
saving mode
●
When battery-saving mode is set, battery
depletion is minimized by stopping the
electronic key from receiving radio
waves.
Press
twice while pressing and
holding .
Confirm that the electronic key indicator
flashes 4 times. While the battery-saving
mode is set, the smart access system with
push-button start cannot be used. To cancel
the function, press any of the electronic key
buttons.
●
Electronic keys that will not be used for
long periods of time can be set to the bat-
tery-saving mode in advance.
■
When electronic key function stops
If the position of the electronic key has not
changed for a certain amount of time such
as when the electronic key is left some-
where, the function of the electronic key
stops to reduce depletion of the battery.
In this case, function can automatically be
restored by moving the position of the key
such as by lifting it up.
■
Conditions affecting operation
The smart access system with push-button
start uses weak radio waves. In the follow-
ing situations, the communication between
the electronic key and the vehicle may be
affected, preventing the smart access sys-
tem with push-button start, wireless remote
control and immobilizer system from oper-
ating properly. (Ways of coping:
P.396)
●
When the electronic key battery is
depleted
●
Near a TV tower, electric power plant,
gas station, radio station, large display,
airport or other facility that generates
strong radio waves or electrical noise
●
When carrying a portable radio, cellular
phone, cordless phone or other wireless
communication device
●
When the electronic key is in contact
with, or is covered by the following metal-
lic objects
• Cards to which aluminum foil is attached
• Cigarette boxes that have aluminum foil
inside
• Metallic wallets or bags
• Coins
• Hand warmers made of metal
• Media such as CDs and DVDs
●
When other wireless keys (that emit
radio waves) are being used nearby
●
When carrying the electronic key
together with the following devices that
emit radio waves
• Another vehicle’s electronic key or a
wireless key that emits radio waves
• Personal computers or personal digital
assistants (PDAs)
• Digital audio players
• Portable game systems
●
If window tint with a metallic content or
metallic objects are attached to the rear
window
●
When the electronic key is placed near a
battery charger or electronic devices
●
When the vehicle is parked in a pay park-
ing spot where radio waves are emitted.
■
Note for the entry function
●
Even when the electronic key is within the
effective range (detection areas), the sys-
tem may not operate properly in the fol-
lowing cases:
• The electronic key is too close to the win-
dow or outside door handle, near the
ground, or in a high place when the doors
are locked or unlocked.
• The electronic key is on the instrument
panel, luggage room, floor, or in the door
pockets or glove box when the hybrid
system is started or power switch modes
are changed.
●
Do not leave the electronic key on top of
the instrument panel or near the door
129
3-2. Opening, closing and locking the doors
3
Before drivi
ng
pockets when exiting the vehicle.
Depending on the radio wave reception
conditions, it may be detected by the
antenna outside the cabin and the door
will become lockable from the outside,
possibly trapping the electronic key
inside the vehicle.
●
As long as the electronic key is within the
effective range, the doors may be locked
or unlocked by anyone. However, only
the doors detecting the electronic key
can be used to unlock the vehicle.
●
Even if the electronic key is not inside the
vehicle, it may be possible to start the
hybrid system if the electronic key is near
the window.
●
The doors may unlock if a large amount
of water splashes on the door handle,
such as in the rain or in a car wash when
the electronic key is within the effective
range. (The doors will automatically be
locked after approximately 60 seconds if
the doors are not opened and closed.)
●
If the wireless remote control is used to
lock the doors when the electronic key is
near the vehicle, there is a possibility that
the door may not be unlocked by the
entry function. (Use the wireless remote
control to unlock the doors.)
●
Touching the door lock sensor while
wearing gloves may delay or prevent
lock operation. Remove the gloves and
touch the lock sensor again.
●
When the lock operation is performed
using the lock sensor, recognition signals
will be shown up to two consecutive
times. After this, no recognition signals
will be given.
●
If the door handle becomes wet while the
electronic key is within the effective
range, the door may lock and unlock
repeatedly. In that case, follow the follow-
ing correction procedures to wash the
vehicle:
• Place the electronic key in a location 6 ft.
(2 m) or more away from the vehicle.
(Take care to ensure that the key is not
stolen.)
• Set the electronic key to battery-saving
mode to disable the smart access system
with push-button start. (
P.128)
●
If the electronic key is inside the vehicle
and a door handle becomes wet during a
car wash, a buzzer may sound outside the
vehicle and “Key Detected in Vehicle”
may be shown on the multi-information
display. To turn off the alarm, lock all the
doors.
●
The lock sensor may not work properly if
it comes into contact with ice, snow, mud,
etc. Clean the lock sensor and attempt to
operate it again.
●
A sudden approach to the effective
range or door handle may prevent the
doors from being unlocked. In this case,
return the door handle to the original
position and check that the doors unlock
before pulling the door handle again.
●
If there is another electronic key in the
detection area, it may take slightly longer
to unlock the doors after the door handle
is gripped.
■
When the vehicle is not driven for
extended periods
●
To prevent theft of the vehicle, do not
leave the electronic key within 6 ft. (2 m)
of the vehicle.
●
The smart access system with push-but-
ton start can be deactivated in advance.
●
Setting the electronic key to battery-sav-
ing mode helps to reduce key battery
depletion. (
P.128)
■
To operate the system properly
Make sure to carry the electronic key when
operating the system. Do not get the elec-
tronic key too close to the vehicle when
operating the system from the outside of
the vehicle.
Depending on the position and holding
condition of the electronic key, the key may
not be detected correctly and the system
may not operate properly. (The alarm may
go off accidentally, or the door lock preven-
tion may not operate.)
■
If the smart access system with push-
button start does not operate properly
●
If the doors cannot be locked or
unlocked, perform the following.
• Bring the electronic key close to the door
handle and perform a lock or unlock
130
3-2. Opening, closing and locking the doors
operation.
• Use the wireless remote control.
If the doors cannot be locked or unlocked
by perform the above, use the mechanical
key. (
P.396)
For Canada: However, if the mechanical
key is used while the alarm system is set, the
warning will sound. (
P.69)
●
If the hybrid system cannot be started,
refer to P.397
■
Customization
Settings (e.g. smart access system with
push-button start) can be changed. (Cus-
tomizable features:
P.429)
If the smart access system with push-button
start has been deactivated by a customized
setting, refer to the explanations for the fol-
lowing operations.
●
Locking and unlocking the doors:
Use the wireless remote control or
mechanical key. (
P.110, 396)
●
Starting the hybrid system and changing
power switch modes:
P.397
●
Stopping the hybrid system:
P.164
WARNING
■
Caution regarding interference with
electronic devices
●
People with implantable cardiac pace-
makers, cardiac resynchronization
therapy-pacemakers or implantable
cardioverter defibrillators should keep
away from the smart access system
with push-button start antennas.
(
P.126)
The radio waves may affect the opera-
tion of such devices. If necessary, the
entry function can be disabled. Ask
your Lexus dealer for details, such as
the frequency of radio waves and tim-
ing of the emitted radio waves. Then,
consult your doctor to see if you
should disable the entry function.
●
Users of any electrical medical device
other than implantable cardiac pace-
makers, cardiac resynchronization
therapy-pacemakers or implantable
cardioverter defibrillators should con-
sult the manufacturer of the device for
information about its operation under
the influence of radio waves.
Radio waves could have unexpected
effects on the operation of such medi-
cal devices.
Ask your Lexus dealer for details on dis-
abling the entry function.
131
3-3. Adjusting the seats
3
Before drivi
ng
3-3.Adjusting the seats
Seat position adjustment switch
Seat cushion (front) angle adjust-
ment switch
Seatback angle adjustment switch
Vertical height adjustment switch
Lumbar support adjustment switch
(for driver’s side)
■
When adjusting the seat
●
Make sure that any surrounding passen-
gers or objects are not contact the seat.
●
Take care when adjusting the seat so that
the head restraint does not touch the ceil-
ing.
■
Power easy access system (if equipped)
The driver’s seat and steering wheel move
in accordance with power switch mode and
the driver’s seat belt condition. (
P.133)
■
Jam protection function (vehicles with
driving position memory)
While the driving position is recalled or the
power easy access system is operating, if an
object is stuck behind the front seat, the
front seat will stop and then slightly move
forward.
When the jam protection function operates,
the seat stops at a position other than the
set seat position. Check the seat position.
Front seats
The seats can be adjusted (longitu-
dinally, vertically, etc.). Adjust the
seat to ensure the correct driving
posture.
Adjustment procedure
A
B
C
D
E
WARNING
■
When adjusting the seat position
●
Take care when adjusting the seat
position to ensure that other passen-
gers are not injured by the moving
seat.
●
Do not put your hands under the seat
or near the moving parts to avoid
injury.
Fingers or hands may become
jammed in the seat mechanism.
●
Make sure to leave enough space
around the feet so they do not get
stuck.
■
Seat adjustment
To reduce the risk of sliding under the lap
belt during a collision, do not recline the
seat more than necessary.
If the seat is too reclined, the lap belt may
slide past the hips and apply restraint
forces directly to the abdomen, or your
neck may contact the shoulder belt,
increasing the risk of death or serious
injury in the event of an accident.
Adjustments should not be made while
driving as the seat may unexpectedly
move and cause the driver to lose con-
trol of the vehicle.
132
3-3. Adjusting the seats
■
Before folding down the rear seat-
backs
1
Park the vehicle in a safe place.
Apply the parking brake firmly and shift the
shift lever to P. (
P.174)
2
Adjust the position of the front seat
and the angle of the seatback.
(
P.131)
Depending on the position of the front
seat, if the seatback is folded backward, it
may interfere with the operation of the rear
seat.
3
Lift up and push down the head
restraints of the rear outboard
seats, and lower the head restraint
of the rear center seat. (
P.137)
4
Stow the armrest of the rear seat if
it is pulled out. (
P.305)
This step is not necessary when operating
the left side seat only.
■
Folding down rear seatbacks
Pull the seatback lock release lever
and fold the seatback down.
■
Returning the rear seatbacks
To avoid trapping the seat belt
between the seat and the inside of the
vehicle, pass the seat belt inside the
seat belt guide
and then return the
seatback securely to the locked posi-
tion.
Rear seats
The seatbacks of the rear seats can
be folded down.
Folding down the rear seatbacks
WARNING
■
When folding the rear seatbacks
down
Observe the following precautions.
Failure to do so may result in death or
serious injury.
●
Do not attempt to fold the seatbacks
down while driving.
●
Stop the vehicle on level ground, set
the parking brake and shift the shift
lever to P.
●
Do not allow anyone to sit on a folded
seatback or in the luggage compart-
ment while driving.
●
Do not allow children to enter the lug-
gage compartment.
●
Do not operate the rear seat if it is
occupied.
●
Be careful not to get feet or hands
caught in the moving parts or joints of
the seats during operation.
●
Do not allow children to operate the
seat.
A
133
3-3. Adjusting the seats
3
Before drivi
ng
*
: If equipped
When all of the following have been
performed, the driver’s seat and steer-
ing wheel are automatically adjusted to
a position that allows the driver to
enter and exit the vehicle easily.
The shift lever has been shifted to P.
The power switch has been turned
off.
The driver’s seat belt has been
WARNING
■
After returning the rear seatback to
the upright position
Observe the following precautions.
Failure to do so may result in death or
serious injury.
●
Make sure that the seatback is
securely locked in position by lightly
pushing it back and forth. If the seat-
back is not securely locked, the red
marking will be visible on the seatback
lock release lever. Make sure that the
red marking is not visible.
●
Check that the seat belts are not
twisted or caught in the seatback.
Driving position memory
*
This feature automatically adjusts
the positions of the driver’s seat,
steering wheel, outside rear view
mirrors and head-up display (if
equipped) to make entering and
exiting the vehicle easier or to suit
your preferences.
Up to 3 different driving positions
can be recorded.
Each electronic key (including a
card key) can be registered to
recall your preferred driving posi-
tion.
Enabling easier driver entry and
exit (power easy access system)
134
3-3. Adjusting the seats
unfastened.
When any of the following has been
performed, the driver’s seat and steer-
ing wheel automatically return to their
original positions.
The power switch has been turned
to ACC or ON.
The driver’s seat belt has been fas-
tened.
■
Operation of the power easy access
system
When exiting the vehicle, the power easy
access system may not operate if the seat is
already close to the rearmost position, etc.
■
Customization
The seat movement amount settings of the
power easy access system can be custom-
ized. (Customizable features:
P.431)
1
Check that the shift lever is in P.
2
Turn the power switch to ON.
3
Adjust the driver’s seat, steering
wheel, outside rear view mirrors
and head-up display (if equipped)
to the desired positions.
4
While pressing the “SET” button, or
within 3 seconds after the “SET”
button is pressed, press button “1”,
“2” or “3” until the buzzer sounds.
If the selected button has already been
preset, the previously recorded position
will be overwritten.
■
Seat positions that can be memorized
(
P.131)
The adjusted positions other than the posi-
tion adjusted by lumbar support switch can
be recorded.
■
In order to correctly use the driving
position memory function
If a seat position is already in the furthest
possible position and the seat is operated in
the same direction, the recorded position
may be slightly different when it is recalled.
1
Check that the shift lever is in P.
2
Turn the power switch to ON.
Recording a driving position into
memory
WARNING
■
Seat adjustment caution
Take care during seat adjustment so that
the seat does not strike the rear passen-
ger or squeeze your body against the
steering wheel.
Recalling a driving position
135
3-3. Adjusting the seats
3
Before drivi
ng
3
Press one of the buttons for the
driving position you want to recall
until the buzzer sounds.
■
To stop the position recall operation
part-way through
Perform any of the following:
●
Press the “SET” button.
●
Press button “1”, “2” or “3”.
●
Operate any of the seat adjustment
switches (only cancels seat position
recall).
●
Operate the tilt and telescopic steering
control switch (only cancels steering
wheel position recall).
■
Operating the driving position memory
after turning the power switch off
Recorded seat positions can be activated
up to 180 seconds after the driver’s door is
opened and another 60 seconds after it is
closed again.
■
When the recorded seat position can-
not be recalled
The seat position may not be recalled in
some situations when the seat position is
recorded in a certain range. For details,
contact your Lexus dealer.
■
Registering procedure
Record your driving position to button
“1”, “2” or “3” before performing the
following:
Carry only the key you want to regis-
ter, and then close the driver’s door.
If 2 or more keys are in the vehicle, the
driving position cannot be recorded
properly.
1
Check that the shift lever is in P.
2
Turn the power switch to ON.
3
Recall the driving position that you
want to record.
4
While pressing the recalled button,
press and hold the door lock switch
(either lock or unlock) until the
buzzer sounds.
If the button could not be registered, the
buzzer sounds continuously for approxi-
mately 3 seconds.
■
Cancelation procedure
1
Carry only the key you want to can-
cel and then close the driver’s door.
If 2 or more keys are in the vehicle, the
driving position cannot be canceled prop-
Registering/canceling/recall-
ing a driving position to an elec-
tronic key (including a card key)
(memory recall function)
136
3-3. Adjusting the seats
erly.
2
Turn the power switch to ON.
3
While pressing the “SET” button,
press and hold the door lock switch
(either lock or unlock) until the
buzzer sounds twice.
If it could not be canceled, the buzzer
sounds continuously for approximately 3
seconds.
■
Recall procedure
1
Make sure that the doors are
locked before recalling the driving
position. Carry the electronic key
that has been registered to the driv-
ing position, and then unlock and
open the driver’s door using the
smart access system with push-but-
ton start or wireless remote control.
The driving position will move to the
recorded position (not including the steer-
ing wheel and head-up display [if
equipped]). However, the seat will move to
a position slightly behind the recorded
position in order to make entering the
vehicle easier.
If the driving position is in a position that
has already been recorded, the seat and
outside rear view mirrors will not move.
2
Turn the power switch to ACC or
ON, or fasten a seat belt.
The seat, steering wheel and head-up dis-
play (if equipped) will move to the
recorded position.
■
Recalling the driving position using the
memory recall function
●
Different driving positions can be regis-
tered for each electronic key. Therefore,
the driving position that is recalled may
be different depending on the key being
carried.
●
If a door other than the driver’s door is
unlocked with the smart access system
with push-button start, the driving posi-
tion cannot be recalled. In this case, press
the driving position button which has
been set.
■
Customization
The unlock door settings of the memory
recall function can be customized. (Cus-
tomizable features:
P.431)
137
3-3. Adjusting the seats
3
Before drivi
ng
■
Front seats
1
Up
Pull the head restraints up.
2
Down
Push the head restraint down while press-
ing the lock release button
.
■
Center rear seat
1
Up
Pull the head restraints up.
2
Down
Push the head restraint down while press-
ing the lock release button
.
■
Outboard rear seats
1
To fold
Pull up the head restraint while pressing
the lock release button
.
2
To use
Lift up and push down the head restraint to
the lowest lock position.
■
Adjusting the height of the head
restraints (front seats)
Make sure that the head restraints are
adjusted so that the center of the head
restraint is closest to the top of your ears.
Head restraints
Head restraints are provided for all
seats.
WARNING
■
Head restraint precautions
Observe the following precautions
regarding the head restraints.
Failure to do so may result in death or
serious injury.
●
Use the head restraints designed for
each respective seat.
●
Adjust the head restraints to the cor-
rect position at all times.
●
After adjusting the head restraints,
push down on them and make sure
they are locked in position.
●
Do not drive with the head restraints
removed.
Vertical adjustment
A
A
A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст