Lexus UX250h (2023 year). Manual in english — page 22
363
6-3. Do-it-yourself maintenance
6
M
ain
ten
an
ce an
d
ca
re
Type D
Normal fuse
Blown fuse
■
After a fuse is replaced
●
When installing the lid, make sure that the
tab is installed securely.
●
If the lights do not turn on even after the
fuse has been replaced, a bulb may need
replacement. (
P.365)
●
If the replaced fuse blows again, have the
vehicle inspected by your Lexus dealer.
■
If there is an overload in a circuit
The fuses are designed to blow, protecting
the wiring harness from damage.
■
When replacing light bulbs
Lexus recommends that you use genuine
Lexus products designed for this vehicle.
Because certain bulbs are connected to cir-
cuits designed to prevent overload, non-
genuine parts or parts not designed for this
vehicle may be unusable.
WARNING
■
To prevent system breakdowns and
vehicle fire
Observe the following precautions.
Failure to do so may cause damage to
the vehicle, and possibly a fire or injury.
●
Never use a fuse of a higher amperage
rating than that indicated, or use any
other object in place of a fuse.
A
B
●
Always use a genuine Lexus fuse or
equivalent.
Never replace a fuse with a wire, even
as a temporary fix.
●
Do not modify the fuses or fuse boxes.
■
Fuse box near the power control unit
Never check or replace the fuses as
there are high voltage parts and wiring
near the fuse box.
Doing so may cause electric shock,
resulting in death or serious injury.
NOTICE
■
Before replacing fuses
Have the cause of electrical overload
determined and repaired by your Lexus
dealer as soon as possible.
364
6-3. Do-it-yourself maintenance
Single-beam headlights
Adjustment bolt A
Adjustment bolt B
Triple-beam headlights
Adjustment bolt A
Adjustment bolt B
Make sure the vehicle has a full tank
of gasoline and the area around the
headlight is not deformed.
Park the vehicle on level ground.
Make sure the tire inflation pressure
is at the specified level.
Have someone sit in the driver’s
seat.
Bounce the vehicle several times.
1
Using a Phillips-head screwdriver,
turn bolt A in either direction.
Remember the turning direction
and the number of turns.
Single-beam headlights
Triple-beam headlights
2
Turn bolt B the same number of
turns and in the same direction as
step
1
.
If the headlight cannot be adjusted using
this procedure, take the vehicle to your
Lexus dealer to adjust the headlight aim.
Headlight aim
Vertical movement adjusting
bolts
Before checking the headlight
aim
A
B
A
B
Adjusting the headlight aim
365
6-3. Do-it-yourself maintenance
6
M
ain
ten
an
ce an
d
ca
re
Single-beam headlights
Triple-beam headlights
Front turn signal light (vehicles with
single-beam headlights)
■
Bulbs that need to be replaced by
your Lexus dealer
Headlights
Parking lights and daytime running
lights
Front turn signal lights (vehicles with
triple-beam headlights)
Fog lights (if equipped)
Cornering lights (if equipped)
Side turn signal lights
Light bulbs
You may replace the following bulb
by yourself. Before replacing,
check the wattage of the light bulb
to be replaced. As there is a danger
that components may be damaged,
we recommend that replacement is
carried out by your Lexus dealer.
Bulb location
A
366
6-3. Do-it-yourself maintenance
Tail lights
Stop lights
Tail lights/stop lights
Rear turn signal lights
Back-up lights
High mounted stoplight
License plate lights
Side marker lights
■
LED lights
Vehicles with single-beam headlights:
The lights other than the front turn signal
light each consist of a number of LEDs. If
any of the LEDs burn out, take your vehicle
to your Lexus dealer to have the light
replaced.
Vehicles with triple-beam headlights:
The lights consist of a number of LEDs. If
any of the LEDs burn out, take your vehicle
to your Lexus dealer to have the light
replaced.
■
Condensation build-up on the inside of
the lens
Temporary condensation build-up on the
inside of the headlight lens does not indi-
cate a malfunction. Contact your Lexus
dealer for more information in the following
situations:
●
Large drops of water have built up on the
inside of the lens.
●
Water has built up inside the headlight.
■
When replacing light bulbs
P.363
■
Front turn signal lights (vehicles
with single-beam headlights)
1
Turn the bulb base counterclock-
wise.
2
Remove the light bulb.
3
When installing, reverse the steps
listed.
Replacing light bulb
WARNING
■
Replacing light bulb
●
Turn off the light. Do not attempt to
replace the bulb immediately after
turning off the light.
The bulb become very hot and may
cause burns.
●
Do not touch the glass portion of the
light bulb with bare hands. When it is
unavoidable to hold the glass portion,
use and hold with a clean dry cloth to
avoid getting moisture and oils on the
bulb.
Also, if the bulb is scratched or
dropped, it may blow out or crack.
367
6-3. Do-it-yourself maintenance
6
M
ain
ten
an
ce an
d
ca
re
WARNING
●
Fully install light bulb and any parts
used to secure it. Failure to do so may
result in heat damage, fire, or water
entering the light unit. This may dam-
age the light or cause condensation to
build up on the lens.
■
To prevent damage or fire
●
Make sure bulb is fully seated and
locked.
●
Check the wattage of the bulb before
installing to prevent heat damage.
369
7
7
W
hen
tro
ub
le
ar
ise
s
When trouble arises
7-1. Essential information
Emergency flashers. . . . ..
370
If your vehicle has to be stopped
in an emergency . . . . . .
370
If the vehicle is submerged or
water on the road is rising ...
371
7-2. Steps to take in an emergency
If your vehicle needs to be towed
. . . . . . . . . . . . . .
373
If you think something is wrong
. . . . . . . . . . . . . .
377
If a warning light turns on or a
warning buzzer sounds . ...
378
If a warning message is displayed
. . . . . . . . . . . . . .
387
If you have a flat tire. . . . ..
392
If the hybrid system will not start
. . . . . . . . . . . . . .
393
If you lose your keys. . . . .
394
If the fuel filler door cannot be
opened. . . . . . . . . .
395
If the electronic key does not
operate properly . . . . .
396
If the 12-volt battery is discharged
. . . . . . . . . . . . . .
398
If your vehicle overheats . .
402
If the vehicle becomes stuck
405
370
7-1. Essential information
7-1.Essential information
Press the switch.
All the turn signal lights will flash. To turn
them off, press the switch once again.
■
Emergency flashers
●
If the emergency flashers are used for a
long time while the hybrid system is not
operating (while the “READY” indicator
is not illuminated), the 12-volt battery may
discharge.
●
If any of the SRS airbags deploy (inflate)
or in the event of a strong rear impact, the
emergency flashers will turn on automati-
cally. The emergency flashers will turn off
automatically after operating for approxi-
mately 20 minutes. To manually turn the
emergency flashers off, press the switch
twice. (The emergency flashers may not
turn on automatically depending on the
force of the impact and conditions of the
collision.)
1
Steadily step on the brake pedal
with both feet and firmly depress it.
Do not pump the brake pedal repeatedly
as this will increase the effort required to
slow the vehicle.
2
Shift the shift lever to N.
If the shift lever is shifted to N
3
After slowing down, stop the vehi-
cle in a safe place by the road.
4
Stop the hybrid system.
If the shift lever cannot be shifted to
N
3
Keep depressing the brake pedal
with both feet to reduce vehicle
speed as much as possible.
4
To stop the hybrid system, press
and hold the power switch for 2
consecutive seconds or more, or
Emergency flashers
The emergency flashers are used to
warn other drivers when the vehi-
cle has to be stopped in the road
due to a breakdown, etc.
Operating instructions
If your vehicle has to be
stopped in an emergency
Only in an emergency, such as if it
becomes impossible to stop the
vehicle in the normal way, stop the
vehicle using the following proce-
dure:
Stopping the vehicle
371
7-1. Essential information
7
W
hen
tro
ub
le
ar
ise
s
press it briefly 3 times or more in
succession.
5
Stop the vehicle in a safe place by
the road.
If the door can be opened, open the
door and exit the vehicle.
If the door can not be opened, open
the window using the power win-
dow switch and ensure an escape
route.
If the window can be opened, exit
the vehicle through the window.
If the door and window cannot be
opened due to the rising water,
remain calm, wait until the water
level inside the vehicle rises to the
point that the water pressure inside
of the vehicle equals the water pres-
sure outside of the vehicle and then
open the door after waiting for the
rising water to enter the vehicle, and
exit the vehicle. When the outside
water level exceeds half the height
of the door, the door cannot be
opened from the inside due to water
pressure.
■
Water level exceeds the floor
When the water level exceeds the floor and
WARNING
■
If the hybrid system has to be turned
off while driving
Power assist for the steering wheel will
be lost, making the steering wheel
heavier to turn. Decelerate as much as
possible before turning off the hybrid
system.
If the vehicle is submerged
or water on the road is rising
This vehicle is not designed to be
able to drive on roads that are
deeply flooded with water. Do not
drive on roads where the roads may
be submerged or the water may be
rising. It is dangerous to remain in
the vehicle, if it anticipated that the
vehicle will be flooded or set a drift.
Remain calm and follow the follow-
ing.
372
7-1. Essential information
time has passed, the electrical equipment
will get damaged, the power windows will
not operate, the engine and motor stop, and
the vehicle may not be able to get moving.
■
Using an emergency escape hammer
*1
Laminated glass
*2
is used in the windshield
and front side windows on this vehicle.
Laminated glass cannot be shattered with
an emergency hammer
*1
.
*1
: Contact your Lexus dealer or
aftermarket accessory manufacturer for
further information about an emergency
hammer.
*2
: If equipped
■
How to distinguish laminated glass
When looking from the cross-sectional
view point, laminated glass is two sheets of
glass pasted together.
Laminated glass
Tempered glass
WARNING
■
Caution while driving
Do not drive on roads where the roads
may be submerged or the water may be
rising. Otherwise the vehicle may be
damaged and cannot move, as well as
become flooded and set a drift, which
may lead to death.
A
B
373
7-2. Steps to take in an emergency
7
W
hen
tro
ub
le
ar
ise
s
7-2.Steps to take in an emergency
The following may indicate a problem
with your transmission. Contact your
Lexus dealer or commercial towing
service before towing.
The hybrid system warning message
is shown on the multi-information
display and the vehicle does not
move.
The vehicle makes an abnormal
sound.
From the front (2WD models)
Release the parking brake.
Turn automatic mode off. (
P.175)
From the front (AWD models)
Use a towing dolly under the rear
wheels.
From the rear
Use a towing dolly under the front
wheels.
If your vehicle needs to be
towed
If towing is necessary, we recom-
mend having your vehicle towed by
your Lexus dealer or commercial
towing service, using a wheel-lift
type truck or flatbed truck.
Use a safety chain system for all
towing, and abide by all state/pro-
vincial and local laws.
Situations when it is necessary to
contact dealers before towing
Towing with a wheel-lift type
truck
WARNING
Observe the following precautions.
Failure to do so may result in death or
serious injury.
374
7-2. Steps to take in an emergency
WARNING
■
When towing the vehicle
2WD models
Be sure to transport the vehicle with the
front wheels raised or with all four wheels
raised off the ground. If the vehicle is
towed with the front wheels contacting
the ground, the drivetrain and related
parts may be damaged or electricity
generated by the operation of the motor
may cause a fire to occur depending on
the nature of the damage or malfunction.
AWD models
Be sure to transport the vehicle with all
four wheels raised off the ground. If the
vehicle is towed with the tires contacting
the ground, the drivetrain or related
parts may be damaged, the vehicle may
fly off the truck, or electricity generated
by the operation of the motor may cause
a fire to occur depending on the nature
of the damage or malfunction.
NOTICE
■
To prevent damage to the vehicle
when towing using a wheel-lift type
truck
When raising the vehicle, ensure ade-
quate ground clearance for towing at the
opposite end of the raised vehicle. With-
out adequate clearance, the vehicle
could be damaged while being towed.
375
7-2. Steps to take in an emergency
7
W
hen
tro
ub
le
ar
ise
s
When using a flat-bed truck to trans-
port the vehicle, use tire strapping
belts. Refer to the owner’s manual of
the flat-bed truck for the tire strapping
method.
In order to suppress vehicle movement
during transportation, set the parking
brake and turn the power switch off.
If a tow truck is not available in an
emergency, your vehicle may be tem-
porarily towed using cables or chains
secured to the emergency towing eye-
let. This should only be attempted on
hard surfaced roads for short distances
at under 18 mph (30 km/h).
A driver must be in the vehicle to steer
and operate the brakes. The vehicle’s
wheels, drivetrain, axles, steering and
brakes must be in good condition.
To have your vehicle towed by another
vehicle, the towing eyelet must be
installed to your vehicle. Install the tow-
ing eyelet using the following proce-
dure.
1
Take out the towing eyelet.
(
P.291, 347)
2
Remove the eyelet cover using a
flathead screwdriver.
To protect the bodywork, place a rag
between the screwdriver and the vehicle
body as shown in the illustration.
3
Insert the towing eyelet into the
hole and tighten partially by hand.
NOTICE
■
Towing with a sling-type truck
Do not tow with a sling-type truck to pre-
vent body damage.
Using a flatbed truck
Emergency towing
Emergency towing procedure
376
7-2. Steps to take in an emergency
4
Tighten down the towing eyelet
securely using a hard metal bar.
5
Securely attach cables or chains to
the towing eyelet.
Take care not to damage the vehicle body.
6
Enter the vehicle being towed and
start the hybrid system.
If the hybrid system does not start, turn the
power switch to ON.
7
Shift the shift lever to N and release
the parking brake.
Turn automatic mode off. (
P.175)
When the shift lever cannot be shifted:
P.170
■
While towing
If the hybrid system is off, the power assist
for the brakes and steering will not function,
making steering and braking more difficult.
■
Wheel nut wrench
Wheel nut wrench can be purchased at
your Lexus dealer.
WARNING
Observe the following precautions. Fail-
ure to do so may result in death or seri-
ous injury.
■
While towing
When towing using cables or chains,
avoid sudden starts, etc. which place
excessive stress on the towing eyelet,
cables or chains. The towing eyelet,
cables or chains may become damaged,
broken debris may hit people, and cause
serious damage.
■
Installing towing eyelets to the vehi-
cle
Make sure that towing eyelets are
installed securely.
If not securely installed, towing eyelets
may come loose during towing.
NOTICE
■
To prevent damage to the vehicle
during emergency towing
Do not secure cables or chains to the
suspension components.
377
7-2. Steps to take in an emergency
7
W
hen
tro
ub
le
ar
ise
s
Fluid leaks under the vehicle
(Water dripping from the air condi-
tioning after use is normal.)
Flat-looking tires or uneven tire
wear
Engine coolant temperature gauge
continually points higher than nor-
mal
Changes in exhaust sound
Excessive tire squeal when corner-
ing
Strange noises related to the sus-
pension system
Pinging or other noises related to
the hybrid system
Engine missing, stumbling or run-
ning roughly
Appreciable loss of power
Vehicle pulls heavily to one side
when braking
Vehicle pulls heavily to one side
when driving on a level road
Loss of brake effectiveness, spongy
feeling, pedal almost touches the
floor
If you think something is
wrong
If you notice any of the following
symptoms, your vehicle probably
needs adjustment or repair. Con-
tact your Lexus dealer as soon as
possible.
Visible symptoms
Audible symptoms
Operational symptoms
378
7-2. Steps to take in an emergency
■
Brake system warning light (warning buzzer)
■
Charging system warning light
*
(warning buzzer)
*
: This light illuminates on the multi-information display.
■
Low engine oil pressure warning light
*
(warning buzzer)
*
: This light illuminates on the multi-information display.
If a warning light turns on or a warning buzzer sounds
Calmly perform the following actions if any of the warning lights comes on or
flashes. If a light comes on or flashes, but then goes off, this does not necessar-
ily indicate a malfunction in the system. However, if this continues to occur,
have the vehicle inspected by your Lexus dealer.
Actions to the warning lights or warning buzzers
Warning light
Details/Actions
(U.S.A.)
or
(red)
(Canada)
Indicates that:
The brake fluid level is low; or
The brake system is malfunctioning
Immediately stop the vehicle in a safe place and contact your
Lexus dealer. Continuing to drive the vehicle may be dangerous.
Warning light
Details/Actions
Indicates a malfunction in the vehicle’s charging system
Immediately stop the vehicle in a safe place and contact your
Lexus dealer.
Warning light
Details/Actions
Indicates that the engine oil pressure is too low
Immediately stop the vehicle in a safe place and contact your
Lexus dealer.
379
7-2. Steps to take in an emergency
7
W
hen
tro
ub
le
ar
ise
s
■
Malfunction indicator lamp (warning buzzer)
■
High coolant temperature warning light
*
(warning buzzer)
*
: This light illuminates on the multi-information display.
■
Tire pressure warning light
■
Brake system warning light (warning buzzer)
Warning light
Details/Actions
(U.S.A.)
or
(Canada)
Indicates a malfunction in:
The hybrid system;
The electronic engine control system; or
The electronic throttle control system
Immediately stop the vehicle in a safe place and contact your
Lexus dealer.
Warning light
Details/Actions
Indicates that the engine coolant temperature is too high
Immediately stop the vehicle in a safe place.
Handling method (
P.402)
Warning light
Details/Actions
When the light comes on after blinking for approximately 1 minute:
Malfunction in the tire pressure warning system
Have the system checked by your Lexus dealer.
When the light comes on:
Low tire inflation pressure such as
Natural causes
Flat tire
P.385
Warning light
Details/Actions
(yellow)
Indicates a malfunction in:
The regenerative braking system;
The electronically controlled brake system; or
The parking brake system
Have the vehicle inspected by your Lexus dealer immediately.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст