Lexus ES300 (1997 year). Manual — part 195
N21207
6
within
60 seconds
13
N21208
within
4 to 40
seconds
3
2
N21209
3
within
60
seconds
2
–
BODY ELECTRICAL
POWER WINDOW CONTROL SYSTEM
BE–115
1499
1997 LEXUS ES300 (RM511U)
(d)
Reverse the polarity, check that the window begins to de-
scend within approximately 60 seconds.
If operation is not as specified, replace the motor.
15.
Front Passenger’s Door Motor:
INSPECT POWER WINDOW MOTOR CIRCUIT
BREAKER OPERATION
(a)
Disconnect the connector from the power window switch.
(b)
Connect the positive (+) lead from the battery to terminal
2 and the negative (–) lead to terminal 3 on the wire har-
ness side connector, and raise the window to full closed
position.
(c)
Continue to apply voltage, check that there is a circuit
breaker operation noise within approximately 4 to 40 se-
conds.
(d)
Reverse the polarity, check that the window begins to de-
scend within approximately 60 seconds.
If operation is not as specified, replace the motor.
16.
Rear Left Side Door:
INSPECT POWER WINDOW MOTOR CIRCUIT
BREAKER OPERATION
See step of Front Passenger Door Motor.
17.
Rear Right Side Door:
INSPECT POWER WINDOW MOTOR CIRCUIT
BREAKER OPERATION
See step of Front Passenger Door Motor.
N21373
Wire Harness Side
1 2
e–2–1–0
Z19529
(b) Close
(c) Open
A3
BE–116
–
BODY ELECTRICAL
POWER WINDOW CONTROL SYSTEM
1500
1997 LEXUS ES300 (RM511U)
18.
INSPECT POWER WINDOW MOTOR CIRCUIT
(a)
Disconnect the connector from the motor.
(b)
Connect the connector to the master switch and power
window switch.
(c)
Inspect the connector on the wire harness side.
Driver’s Door Motor
Tester connection
Condition
Specified condition
1 – Ground
*Master switch position DOWN or OFF
No voltage
1 – Ground
*Master switch position UP
Battery positive voltage
2 – Ground
*Master switch position UP or OFF
No voltage
2 – Ground
*Master switch position DOWN
Battery positive voltage
Except Driver’s Door Motor
Tester connection
Condition
Specified condition
1 – Ground
*Master switch position UP or OFF
No voltage
1 – Ground
*Master switch position DOWN
Battery positive voltage
1 – Ground
*Power window switch position UP or OFF
No voltage
1 – Ground
*Power window switch position DOWN
Battery positive voltage
2 – Ground
*Master switch position DOWN or OFF
No voltage
2 – Ground
*Master switch position UP
Battery positive voltage
2 – Ground
*Power window switch position DOWN or OFF
No voltage
2 – Ground
*Power window switch position UP
Battery positive voltage
*: Set the window lock switch to the unlock position.(except driv-
er’s door motor)
If the circuit is not as specified, inspect the circuits connected
to other parts.
19.
Key–Off Power Window Signal:
INSPECT INTEGRATION RELAY OPERATION
HINT:
When the relay circuit is as specified, inspect the key–off power
window signal.
(a)
Connect the positive (+) lead from the voltmeter to termi-
nal A3 and the negative (–) lead to body ground.
(b)
Close the door with ignition switch turned to LOCK or
ACC, and check that the meter needle indicates battery
positive voltage.
Z19530
A3
–
BODY ELECTRICAL
POWER WINDOW CONTROL SYSTEM
BE–117
1501
1997 LEXUS ES300 (RM511U)
(c)
Open the door and check that the meter needle indicates
0 V.
(d)
Turn the ignition switch ON and check that the meter
needle indicates battery positive voltage again.
If operation is not as specified, replace the relay.
20.
INSPECT INTEGRATION RELAY CIRCUIT
(See page
Z19372
Door Lock Control Switch
Ignition Switch
Power Window Master Switch
DOOR Lock Control Switch
Instrument Panel Junction Block
DOOR Fuse
ECU–IG Fuse
Integration Relay
Door Key Lock and Unlock Switch
Door Lock Assembly
Door Lock Motor
Door Unlock Detection Switch
Door Lock Assembly
Door Lock Motor
Door Unlock Detection Switch
BE05O–01
BE–118
–
BODY ELECTRICAL
POWER DOOR LOCK CONTROL SYSTEM
1502
1997 LEXUS ES300 (RM511U)
POWER DOOR LOCK CONTROL SYSTEM
LOCATION
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст