Lexus ES300 (1997 year). Manual — part 520
SF05S–03
S04591
S04590
SF–14
–
SFI
FUEL PRESSURE REGULATOR
865
1997 LEXUS ES300 (RM511U)
REMOVAL
1.
REMOVE FUEL PUMP ASSEMBLY FROM FUEL TANK
(See page
2.
REMOVE FUEL FILTER
(a)
Remove the screw, and pull out the fuel filter.
(b)
Remove the O–ring from the fuel filter.
HINT:
At the time of installation, please refer to the following item.
Apply a light coat of gasoline to a new O–ring, and install it to
the fuel filter.
Torque: 2.0 N·m (20 kgf·cm, 17 in.·lbf)
3.
REMOVE FUEL PRESSURE REGULATOR
(a)
Remove the screw, and pull out the pressure regulator.
Torque: 2.0 N·m (20 kgf·cm, 17 in.·lbf)
(b)
Remove the O–ring from the pressure regulator.
HINT:
At the time of installation, please refer to the following item.
Apply a light coat of gasoline to a new O–ring, and install it to
the pressure regulator.
SF05T–01
–
SFI
FUEL PRESSURE REGULATOR
SF–15
866
1997 LEXUS ES300 (RM511U)
INSTALLATION
Installation is in the reverse order of removal (See page
S05625
5 mm
Hexagon
Wrench
Clip
SF072–06
S04535
Sound Scope
S04534
Ohmmeter
SF–16
–
SFI
INJECTOR
867
1997 LEXUS ES300 (RM511U)
INJECTOR
ON–VEHICLE INSPECTION
1.
REMOVE V–BANK COVER
(a)
Using a 5 mm hexagon wrench, remove the 2 cap nuts.
(b)
Disconnect the 2 clips, and remove the V–bank cover.
2.
INSPECT INJECTOR OPERATION
Check operation sound from each injector.
(1)
With the engine running or cranking, use a sound
scope to check that there is normal operating noise
in proportion to engine speed.
(2)
If you have no sound scope, you can check the in-
jector operating vibration with your finger.
If no sound or unusual sound is heard, check the wiring connec-
tor, injector or injection signal from the ECM.
3.
INSPECT INJECTOR RESISTANCE
(a)
Disconnect the injector connector.
(b)
Using an ohmmeter, measure the resistance between the
terminals.
Resistance: 13.8
Ω
at 20
°
C (68
°
F)
If the resistance is not as specified, replace the injector.
(c)
Reconnect the injector connector.
4.
REINSTALL V–BANK COVER
HINT:
For fixing the V–bank cover, push on the cover until a ”click” is
felt.
SF073–05
S05371
PS Pressure Tube
Air Intake Chamber Stay
19.5 (200, 14)
39 (400, 19)
12 (120, 9)
V–Bank Cover
Gasket
No.2 EGR Pipe
Throttle Position
Sensor Connector
Gasket
Brake Booster
Vacuum Hose
EGR Valve Position
Sensor Connector
Accelerator Cable
Throttle Cable
Air Cleaner
Hose
IAC Valve
Connector
EGR Gas Temperature
Sensor Connector
EVAP Hose
Water Bypass Hose
Vacuum
Hose
Gasket
VSV Connector for ASIC
No.1 Engine
Hanger
Ground Cable
Ground Cable
Ground Strap
DLC1
PCV Hose
Air Intake Chamber
Assembly
Water Bypass Hose
Air Assist Hose and Pipe
19.5 (200, 14)
Retainer
Injector Connector
Delivery Pipe
10 (100, 7)
Spacer
O–Ring
Grommet
Grommet
O–Ring
N·m (kgf·cm, ft·lbf)
: Specified
Non–reusable part
43 (440, 32)
VSV Connector
for EGR
Engine Wire
VSV Connector
for EVAP
Injector
High–Tension Cord
Set
–
SFI
INJECTOR
SF–17
868
1997 LEXUS ES300 (RM511U)
COMPONENTS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст