Lexus ES300 (1997 year). Manual — part 157
V08545
A
Shape
Size
B
C
D
E
F
G
H
I
J
K
Shape
Size
Shape
Size
mm (in.)
ø = 8
(0.31)
L = 22
(0.87)
ø = 6
(0.24)
L = 20
(0.79)
ø = 6
(0.24)
L = 16
(0.63)
ø = 6
(0.24)
L = 16
(0.63)
ø = 6
(0.24)
L = 20
(0.79)
ø = 6
(0.24)
L = 18
(0.71)
ø = 5.22
(0.2055)
L = 20
(0.79)
ø = 5.22
(0.2055)
L = 16
(0.63)
ø = 8
(0.31)
ø = 6
(0.24)
ø = 6
(0.24)
–
BODY
INSTRUMENT PANEL
BO–81
1259
1997 LEXUS ES300 (RM511U)
HINT:
Screw shapes and sizes are indicated in the table below. The codes (A – K) correspond to those indicated
on the previous pages.
BO0AS–03
N21447
: 4 Clips
N21448
: 2 Clips
W03621
BO–82
–
BODY
INSTRUMENT PANEL
1260
1997 LEXUS ES300 (RM511U)
REMOVAL
1.
REMOVE THESE PARTS:
(a)
Front pillar garnishes
(b)
Front door scuff inside plates
(c)
Front door opening trim covers
(d)
Cowl side trims
2.
REMOVE STEERING WHEEL
(See page
3.
REMOVE THESE PARTS:
(a)
Steering column cover
(b)
Combination switch
4.
REMOVE NO.1 LOWER PANEL
(a)
Remove the 2 screws and hood release lever.
(b)
Remove the bolt, screw and No.1 lower panel, then dis-
connect the connectors.
5.
REMOVE LOWER LH PANEL
6.
REMOVE LOWER FINISH PANEL
Using a screwdriver, remove the lower finish panel.
7.
REMOVE THESE PARTS:
(a)
Cluster finish panel
(b)
Combination meter
8.
REMOVE NO.2 UNDER COVER
(a)
Using a screwdriver, remove the lower cover.
HINT:
Tape the screwdriver tip before use.
(b)
Pull up the connector.
(c)
Disconnect the passenger airbag connector.
NOTICE:
When disconnecting the passenger airbag connector take
care not to damage the airbag wire harness.
(d)
Remove the No.2 under cover.
W03622
N21449
: 4 Clips
N21412
–
BODY
INSTRUMENT PANEL
BO–83
1261
1997 LEXUS ES300 (RM511U)
9.
REMOVE THESE PARTS:
(a)
Lower panel
(b)
Finish upper panel
(c)
CD changer assembly
(d)
Lower No.1 finish panel retainer
10.
REMOVE FRONT PASSENGER AIRBAG ASSEMBLY
(See page
(a)
Remove the 2 bolts from the instrument panel reinforce-
ment.
Torque: 20 N·m (204 kgf·cm, 15 ft·lbf)
(b)
Remove the 4 nuts and front passenger airbag assembly.
CAUTION:
Do not store the front passenger airbag assembly with the
airbag deployment direction facing down. Never disas-
semble the front passenger airbag assembly.
NOTICE:
At the time of installation, please refer to the following item.
Make sure that the front passenger airbag assembly is
installed to the specified torque. When installing the instru-
ment panel, take care that the airbag wire harness does not
interfere with other parts and is not pinched between other
parts.
11.
REMOVE UPPER CONSOLE PANEL
Using a screwdriver, remove the upper console panel.
HINT:
Tape the screwdriver tip before use.
12.
REMOVE REAR CONSOLE BOX
(a)
Remove the box bottom No.2 mat.
(b)
Remove the 2 bolts, 2 screws and rear console box, then
disconnect the connector.
(c)
Remove the rear cup holder and rear ash receptacle.
N21451
: 4 Clips
N21450
: 2 Clips
N21452
: 2 Clips
N21453
LH Side
BO–84
–
BODY
INSTRUMENT PANEL
1262
1997 LEXUS ES300 (RM511U)
13.
REMOVE END CLUSTER FINISH PANEL
Using a screwdriver, remove the panel.
HINT:
Tape the screwdriver tip before use.
14.
REMOVE CENTER CLUSTER FINISH PANEL
Using a screwdriver, remove the panel, then disconnect the
connectors.
HINT:
Tape the screwdriver tip before use.
15.
REMOVE THESE PARTS:
(a)
Radio and A/C control panel assembly
(b)
Front ash receptacle
16.
REMOVE FRONT CONSOLE BOX
Remove the 4 screws and front console box.
17.
REMOVE THESE PARTS:
(a)
LH and RH floor carpet brackets
(b)
Lower No.2 finish panel retainer
(c)
Nozzle side defroster No.1
18.
REMOVE INSTRUMENT PANEL SAFETY PAD
(a)
Using a screwdriver, remove the No.2 side defroster
nozzle.
HINT:
Tape the screwdriver tip before use.
(b)
Disconnect the connectors.
(c)
Remove the bolt.
(d)
Remove the connector holder.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст