Lexus ES300 (1997 year). Manual — part 279
R00934
Pedal Reserve Distance
–
BRAKE
BRAKE PEDAL
BR–7
1122
1997 LEXUS ES300 (RM511U)
HINT:
The freeplay to the 1st resistance is due to the play between the
clevis and pin. This is magnified up to 1 – 6 mm (0.04 – 0.24 in.)
at the pedal.
If incorrect, check the stop light switch clearance. If the clear-
ance is OK, then troubleshoot the brake system.
4.
CHECK PEDAL RESERVE DISTANCE
(a)
Release the parking brake.
(b)
With the engine running, depress the pedal and measure
the pedal reserve distance, as shown.
Pedal reserve distance from asphalt sheet at 490 N
(50 kgf, 110.2 lbf): More than 70 mm (2.76 in.)
If the reserve distance is incorrect, troubleshoot the brake sys-
tem.
W03174
BR065–01
W03175
Adjusting Hexagon
No.4
Cable
Lock Nut
W03176
Red Paint
BR–8
–
BRAKE
PARKING BRAKE PEDAL
1123
1997 LEXUS ES300 (RM511U)
PARKING BRAKE PEDAL
ON–VEHICLE INSPECTION
1.
CHECK PARKING BRAKE PEDAL TRAVEL
Slowly depress the parking brake pedal all the way, and count
the number of clicks.
Parking brake pedal travel at 294 N (30 kgf, 66 lbf):
3 – 6 clicks
If incorrect, adjust the parking brake.
2.
IF NECESSARY, ADJUST PARKING BRAKE PEDAL
TRAVEL
HINT:
Before adjusting the parking brake, make sure that the rear
brake shoe clearance has been adjusted.
For shoe clearance adjustment, see step 1 on page
(a)
Remove the console upper panel and console box.
(b)
Confirm that the parking pedal is released.
(c)
Hold the screw end of No.4 cable not to rotate.
(d)
Loosen the lock nut.
(e)
Hold the parking brake cable and turn the adjusting hexa-
gon until the pedal travel is correct.
NOTICE:
To prevent the parking brake cable from twisting, must al-
ways keep the red–painted surface up.
(f)
Holding the adjusting hexagon, tighten the lock nut.
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
(g)
Install the console box and console upper panel.
BR066–03
W03173
W03173
Parking Brake Pedal Assebly
Parking Brake Switch
Parking Brake Cable
N·m (kgf·cm, ft·lbf)
: Specified torque
Pad
36 (370, 27)
Clip
–
BRAKE
PARKING BRAKE PEDAL
BR–9
1124
1997 LEXUS ES300 (RM511U)
COMPONENTS
BR067–01
BR–10
–
BRAKE
PARKING BRAKE PEDAL
1125
1997 LEXUS ES300 (RM511U)
REMOVAL
1.
RELEASE PARKING BRAKE PEDAL
2.
DISCONNECT PARKING BRAKE SWITCH CONNECTOR
3.
REMOVE PARKING BRAKE PEDAL ASSEMBLY
Remove the 3 nuts and parking brake pedal assembly.
Torque: 36 N·m (370 kgf·cm, 27 ft·lbf)
4.
DISCONNECT PARKING BRAKE WIRE
Remove clip and disconnect the parking brake wire.
5.
REMOVE PARKING BRAKE SWITCH
Remove the screw and parking brake switch.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст