Lexus ES300 (1997 year). Manual — part 389
AB0069
W01933
AB0118
R13006
AB0069
AB0118
W02042
H00006
Airbag Sensor
Assembly
Spiral
Cable
P Squib
D Squib
P+
P–
D+
D–
ACC
ON
or
Code 11
DLC1
Tc
E1
–
DIAGNOSTICS
SUPPLEMENTAL RESTRAINT SYSTEM
DI–333
485
1997 LEXUS ES300 (RM511U)
NG
Repair or replace harness or connector be-
tween the airbag sensor assembly and front
passenger airbag assembly.
OK
4
Check airbag sensor assembly.
PREPARATION:
(a)
Connect connector to airbag sensor assembly.
(b)
Using a service wire connect D+ and D– on spiral cable
side of connector between spiral cable and steering
wheel pad.
(c)
Using a service wire, connect P+ and P– on airbag sensor
assembly side of connector between airbag sensor as-
sembly and front passenger airbag assembly.
(d)
Connect negative (–) terminal cable to battery, and wait
at least 2 seconds.
CHECK:
(a)
Turn ignition switch to ACC or ON and wait at least 20 se-
conds.
(b)
Clear malfunction code stored in memory
(See page
(c)
Turn ignition switch to LOCK, and wait at least 20 se-
conds.
(d)
Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(e)
Using SST, connect terminals Tc and E1 of DLC 1.
SST 09843–18020
(f)
Check DTC
OK:
DTC 11 is not output.
HINT:
Codes other than code 11 may be output at this time, but they
are not relevant to this check.
NG
Replace airbag sensor assembly.
OK
R05896
AB0118
R13006
AB0119
W02042
H00007
Spiral
Cable
P Squib
D Squib
ACC
ON
or
DLC1
Code 11
E1
Tc
Airbag Sensor
Assembly
DI–334
–
DIAGNOSTICS
SUPPLEMENTAL RESTRAINT SYSTEM
486
1997 LEXUS ES300 (RM511U)
5
Check D squib.
PREPARATION:
(a)
Turn ignition switch to LOCK.
(b)
Disconnect negative (–) terminal cable from the battery,
and wait at least 90 seconds.
(c)
Connect steering wheel pad connector.
(d)
Connect negative (–) terminal cable to the battery, and
wait at least 2 seconds.
CHECK:
(a)
Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(b)
Clear malfunction code stored in memory
(See page
(c)
Turn ignition switch to LOCK, and wait at least 20 se-
conds.
(d)
Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(e)
Using SST, connect terminals Tc and E1 of DLC 1.
SST 09843–18020
(f)
Check DTC.
OK:
DTC 11 is not output.
HINT:
Codes other than code 11 may be output at this time, but they
are not relevant to this check.
NG
Replace steering wheel pad.
OK
R05897
AB0118
R13006
AB0119
W02042
H00008
Airbag Sensor
Assembly
Spiral
Cable
P Squib
D Squib
ACC
ON
or
DLC1
E1
Tc
Code 11
–
DIAGNOSTICS
SUPPLEMENTAL RESTRAINT SYSTEM
DI–335
487
1997 LEXUS ES300 (RM511U)
6
Check P squib.
PREPARATION:
(a)
Turn ignition switch to LOCK.
(b)
Disconnect negative (–) terminal cable from the battery,
and wait at least 90 seconds.
(c)
Connect front passenger airbag assembly connector.
(d)
Connect negative (–) terminal cable to battery, and wait
at least 2 seconds.
CHECK:
(a)
Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(b)
Clear malfunction code stored in memory
(See page
(c)
Turn ignition switch to LOCK, and wait at least 20 se-
conds.
(d)
Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(e)
Using SST, connect terminals Tc and E1 of DLC 1.
SST 09843–18020
(f)
Check DTC.
OK:
DTC 11 is not output.
HINT:
Codes other than code 11 may be output at this time, but they
are not relevant to this check.
NG
Replace front passenger airbag assembly.
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check. If the malfunctioning part can not be
detected by the simulation method, replace all SRS components including the wire harness.
R05899
R14301
H00009
Airbag Sensor
Assembly
Spiral
Cable
P Squib
D Squib
D+
(+)
(–)
DI–336
–
DIAGNOSTICS
SUPPLEMENTAL RESTRAINT SYSTEM
488
1997 LEXUS ES300 (RM511U)
7
Check spiral cable.
PREPARATION:
Disconnect connector between airbag sensor assembly and
spiral cable.
CHECK:
Measure resistance between D+ on spiral cable side of connec-
tor between spiral cable and steering wheel pad and body
ground.
OK:
Resistance: 1M
Ω
or Higher
NG
Repair or replace spiral cable.
OK
Repair or replace harness or connector be-
tween airbag sensor assembly and spiral
cable.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст