Lexus ES300 (1997 year). Manual — part 117
V08443
19
Is bulb OK?
Replace the bulb. Then recheck system.
Disconnect connector ”D” from meter.
Inspect connector on wire harness side as follows.
HINT : While carrying out the following inspection, make certain that the connectors and terminals are properly con-
nected.
Turn ignition switch ON.
Is there battery positive voltage between terminals
xx and ground with the turn signal lever to left and
right?
Yes
Abnormal operation or warning light
does not light up.
Turn signal indicator signal circuit faulty.
Inspect the turn signal and hazard warning light
system.
Replace circuit plate. Then recheck system.
Turn signal to
Terminal xx
Left
B11
Right
B13
No
TURN SIGNAL INDICATOR
Yes
No
20
Is bulb OK?
Replace the bulb. Then recheck system.
Inspect connector on wire harness side as follows.
HINT : While carrying out the following inspection, make certain that the connectors and terminals are properly con-
nected.
Ground terminal D6 and turn ignition switch ON.
Does TRAC OFF indicator light up?
Yes
Abnormal operation or indicator does
not light up.
Inspect the wire harness between terminal D6 of
meter and ABS & TRAC ECU or inspect ABS &
TRAC ECU.
Replace circuit plate. Then recheck system.
No
TRAC OFF INDICATOR
Yes
No
Replace power source unit.
No
Yes
BE–74
–
BODY ELECTRICAL
COMBINATION METER
1458
1997 LEXUS ES300 (RM511U)
V08444
Is bulb OK?
Replace the bulb.
Disconnect connector ”B” from meter.
Inspect connector on combination meter side as
follows.
HINT : While carrying out the following inspection, make certain that the connectors and terminals are properly con-
nected.
Abnormal operation or indicator does
not light up.
Replace circuit plate. Then recheck system.
Yes
No
Yes
No
21
O/D OFF INDICATOR
Ground terminal B5 and turn ignition switch ON.
Does O/D OFF indicator light up?
O/D OFF indicator signal circuit faulty.
HINT : While carrying out the following inspection, make certain that the connectors and terminals are properly con-
nected.
Disconnect connector ”D” from meter.
Inspect connector on wire harness side as follows.
Is bulb OK?
Replace circuit plate. Then recheck system.
Replace the bulb. Then recheck system.
Shift position indicator signal circuit faulty.
22
SHIFT POSITION INDICATOR
Turn ignition switch ON.
Is there battery positive voltage between terminals
XX and ground with turn shift lever to P through L
Shift to
Terminal XX
P
B12
R
B14
N
C1
D
C2
2
B10
L
B9
Abnormal operation or indicator does
not light up.
Yes
Yes
No
No
–
BODY ELECTRICAL
COMBINATION METER
BE–75
1459
1997 LEXUS ES300 (RM511U)
V08445
Is bulb OK?
Disconnect connector ”D” from meter.
Inspect connector on wire harness side as follows.
HINT : While carrying out the following inspection, make certain that the connectors and terminals are properly con-
nected.
Replace fuse. Then recheck system.
No
Yes
23
MALFUNCTION WARNING
Ground terminal D5 and turn ignition switch ON.
Does check engine warning light light up?
Replace the bulb.
Then recheck system.
Turn ignition switch ON.
Is there battery positive voltage between terminal
D3 and ground?
Replace circuit plate.
Replace combination
meter computer.
Then recheck system.
Temporarily install another circuit plate.
Is operation normal?
Open circuit in wire harness between GAUGE fuse
and meter.
Is GAUGE fuse normal?
Connect connector ”D” to meter.
Disconnect connector ”D” from meter.
Inspect connector on combination meter side as
follows.
Wire harness faulty between ECM and meter.
ECM faulty.
Yes
Yes
Yes
No
No
No
Yes
No
Abnormal operation or warning light
does not light up.
COMBINATION
METER
BE–76
–
BODY ELECTRICAL
COMBINATION METER
1460
1997 LEXUS ES300 (RM511U)
V08446
Is bulb OK?
Disconnect connector ”D” from meter.
Inspect connector on wire harness side as follows.
HINT : While carrying out the following inspection, make certain that the connectors and terminals are properly con-
nected.
Replace fuse. Then recheck system.
No
Yes
Ground terminal D7 and turn ignition switch ON.
Does ABS warning light light up?
Replace bulb.
Then recheck system.
Turn ignition switch ON.
Is there battery positive voltage between terminal
D3 and ground?
Replace circuit plate.
Replace combination
meter computer.
Then recheck system.
Temporarily install another circuit plate.
Is operation normal?
Open circuit in wire harness between GAUGE fuse
and meter.
Is GAUGE fuse normal?
Connect connector ”D” to meter.
Disconnect connector ”D” from meter.
Inspect connector on combination meter side as
follows.
Wire harness faulty between ABS ECU and meter.
ABS ECU faulty.
Yes
Yes
No
No
No
Yes
No
COMBINATION
METER
24
ABS WARNING
Abnormal operation or warning light
does not light up.
–
BODY ELECTRICAL
COMBINATION METER
BE–77
1461
1997 LEXUS ES300 (RM511U)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст