Lexus ES300 (1997 year). Manual — part 601
Lexus Special Service Campaign XL−7
19
1. OPERATION FLOW CHART
2. LOCATION OF AFFECTED PART
Re−torque steering wheel set
nut to specification as outlined
in the Technical Instructions.
Affix SSC completion label
(from owner notification) on the
specified location.
Vehicle does not require
the SSC.
No action required.
Eligible
Verify Vehicle Eligibility:
1. Check VIN Range.
2. Check for SSC Completion
Label.
3. Check TDN.
Not Eligible
Return the vehicle to the
customer.
Steering Wheel Set Nut on 1994 1998 Tsutsumi Built ES 300s
20
3. AFFECTED VIN RANGE
VIN Range*
Model
Year
VDS
Ranges
1994
GK13T
R0001027 through R0074672
1995
GK13T
S0055163 through S0129614
1996
BF12G
T0128626 through T0186198
1997
BF22G
V0001020 through V0083880
ES300
1998
BF28G
W0082398 through W0141594
*
Please note that Kyushu built ES300s are not affected and are not included in the above VIN range. As
always confirm Lexus Service History to verify vehicle eligibility.
4. PREPARATION
Parts
No replacement parts are necessary.
Tools
•
09042−00010
Torx
®
Socket T30
•
Torque
Wrench
•
Standard
Tools
Lexus Special Service Campaign XL−7
21
5. WORK PROCEDURE
1. DISCONNECT NEGATIVE (−) BATTERY
TERMINAL
(a) Record radio station presets.
(b) Set memory seat to position 1.( If
equipped)
(c) Turn the ignition key to the LOCK
position.
(d) Disconnect negative (−) battery terminal.
CAUTION:
Do not remove the Steering Wheel Pad
until a minimum of 90 seconds has
passed since the ignition key was set in
the LOCK position and the battery had
been disconnected.
2. REMOVE STEERING WHEEL PAD
NOTE:
If the airbag is disconnected with the
ignition in the ON or ACC position, a
DTC will be recorded.
(a) Turn the steering wheel so the front
wheels face straight ahead.
(b) Remove the two covers behind the
steering wheel to expose the Torx®
screws.
(c) Using a T30 Torx® socket, loosen the
screws.
NOTE:
•
Loosen the Torx® screws until the
groove, along the screw circumference,
catches on the screw case.
•
Be careful not to damage the cruise
control switch, if equipped.
Steering Wheel Set Nut on 1994 1998 Tsutsumi Built ES 300s
22
(d) Pull the steering wheel pad out from the
steering wheel and disconnect the SRS
connector.
NOTE:
When removing the wheel pad, take
care not to damage the airbag harness.
CAUTION:
When storing the airbag, keep the
upper surface of the airbag facing up.
3. TIGHTEN THE STEERING WHEEL SET
NUT
Torque: 49 N
m (500 kgfcm, 36 ftlbf)
4. REINSTALL THE STEERING WHEEL
PAD
(a) Reconnect the airbag connector.
(b) Reinstall the steering wheel pad after
confirming that the circumference
groove of the Torx® screws are caught
in the screw case.
(c) Using a T30 Torx® socket, tighten the
screws.
Torque:
1994−1996 MY
8.8 N
m (90 kgfcm, 78 inlbf)
1997−1998 MY
7.1 N
m (72 kgfcm, 63 inlbf)
(d) Reinstall the Torx® bolt covers on the
steering wheel.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст