Lexus ES300 (1997 year). Manual — part 396
H00003
ON
–
DIAGNOSTICS
SUPPLEMENTAL RESTRAINT SYSTEM
DI–361
513
1997 LEXUS ES300 (RM511U)
3
Does SRS warning light turn off?
PREPARATION:
(a)
Turn ignition switch to LOCK.
(b)
Connect steering wheel pad connector.
(c)
Connect front passenger airbag assembly connector.
(d)
Connect airbag sensor assembly connector.
(e)
Turn ignition switch ON.
CHECK:
Operate electric system (defogger, wiper, headlight, heater
blower, etc.) and check that SRS warning light goes off.
NO
Check for DTCs. If a DTC is output, perform trou-
bleshooting for the DTC. If a normal code is out-
put, replace airbag sensor assembly.
YES
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check.
W04366
Battery
ECU–
B
8
16
2
3
SRS Warning
Light
A
A
A
LA
ED
BR
Airbag
Sensor
Assembly
DLC1
E1
AB
LG
W–B
J1 Junction
Connector
7
Instrument
Panel J/B
Engine
Room J/B
1G
1W
2J
2A
Fusible Link
Block
FL MAIN
3.0 W
W–R
B
B–G
5
7
1
S
hor
t
pin
F6
1G2
IK3
F8
9
2
B–Y
B–Y
B–Y
5
LG
1
1
E1
BR
3
A
A
W–B
1J
1N
1
II
A
A
J15
Junction
Connector
J24
Junction
Connector
Instrument
Panel J/B
10A
7
W–R
DI–362
–
DIAGNOSTICS
SUPPLEMENTAL RESTRAINT SYSTEM
514
1997 LEXUS ES300 (RM511U)
SRS Warning Light Circuit Malfunction (Always lights up, when
ignition switch is in LOCK position.)
CIRCUIT DESCRIPTION
The SRS warning light is located on the combination meter.
When the SRS is normal, the SRS warning light lights up for approx. 6 seconds after the ignition switch is
turned from the LOCK position to ACC or ON position, and then turns off automatically.
If there is a malfunction in the SRS, the SRS warning light lights up to inform the driver of the abnormality.
When terminals Tc and E1 of the DLC1 are connected, the DTC is displayed by the blinking of the SRS warn-
ing light.
WIRING DIAGRAM
DI0B8–01
H00094
Airbag Sensor
Assembly
Spiral
Cable
P squib
D squib
LOCK
AB0117
W02765
H00044
Airbag Sensor Assembly
LOCK
–
DIAGNOSTICS
SUPPLEMENTAL RESTRAINT SYSTEM
DI–363
515
1997 LEXUS ES300 (RM511U)
INSPECTION PROCEDURE
1
Preparation.
PREPARATION:
(a)
Disconnect negative (–) terminal cable from the battery,
and wait at least 90 seconds.
(b)
Remove steering wheel pad
(See page
(c)
Disconnet connector of front passenger airbag assembly
(See page
CAUTION:
Store the steering wheel pad with the front surface facing
upward.
2
Does SRS warning light turn off?
PREPARATION:
(a)
Turn ignition switch to LOCK.
(b)
Disconnect negative (–) terminal cable from the battery,
and wait at least 90 seconds.
(c)
Disconnect airbag sensor assembly connector.
(d)
Connect negative (–) terminal cable to battery.
CHECK:
Check operation of SRS warning light.
NO
Check SRS warning light circuit or terminal AB
circuit of DLC1.
YES
Replace airbag sensor assembly.
W04366
Battery
ECU–
B
8
16
2
3
SRS Warning
Light
A
A
A
LA
ED
BR
Airbag
Sensor
Assembly
DLC1
E1
AB
LG
W–B
J1 Junction
Connector
7
Instrument
Panel J/B
Engine
Room J/B
1G
1W
2J
2A
Fusible Link
Block
FL MAIN
3.0 W
W–R
B
B–G
5
7
1
S
hor
t
pin
F6
1G2
IK3
F8
9
2
B–Y
B–Y
B–Y
5
LG
1
1
E1
BR
3
A
A
W–B
1J
1N
1
II
A
A
J15
Junction
Connector
J24
Junction
Connector
Instrument
Panel J/B
10A
7
W–R
DI–364
–
DIAGNOSTICS
SUPPLEMENTAL RESTRAINT SYSTEM
516
1997 LEXUS ES300 (RM511U)
SRS Warning Light Circuit Malfunction (Does not light up, when
ignition switch is turned to ACC or ON.)
CIRCUIT DESCRIPTION
The SRS warning light is located on the combination meter.
When the SRS is normal, the SRS warning light lights up for approx. 6 seconds after the ignition switch is
turned from LOCK position to ACC or ON position, and then turns off automatically.
If there is a malfunction in the SRS, the SRS warning light lights up to inform the driver of the abnormality
When terminals Tc and E1 of the DLC1 are connected, the DTC is displayed by the blinking of the SRS warn-
ing light.
WIRING DIAGRAM
DI0B9–01
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст