Lexus ES300 (1997 year). Manual — part 153
BO3986
BO3671
Adhesive
Adhesive
N21432
USA:
–
BODY
WINDSHIELD
BO–65
1243
1997 LEXUS ES300 (RM511U)
(c)
Use a scraper to remove any excessive or protruding
adhesive.
(d)
Hold the glass in place securely with a protective tape or
equivalent until the adhesive hardened.
NOTICE:
Take care not to drive the vehicle during the time described
in the chart below.
Temperature
Minimum time prior to drive the vehicle
35
°
C (95
°
F)
1.5 hour
20
°
C (68
°
F)
5 hour
5
°
C (41
°
F)
24 hour
12.
INSPECT FOR LEAKS AND REPAIR
(a)
Do a leak test after the hardening time has elapsed.
(b)
Seal any leak with sealant.
Part No. 08833–00030 or equivalent
13.
APPLY ADHESIVE AT MOULDING INSTALLATION
AREA
Coat the glass with adhesive at the moulding installation area.
Part No. 08833–00030 or equivalent
14.
USA:
INSTALL WINDSHIELD MOULDING
Place the moulding onto the body and tap it by hand.
N22038
A – A
B – B
A
A
B
B
CANADA:
BO–66
–
BODY
WINDSHIELD
1244
1997 LEXUS ES300 (RM511U)
15.
CANADA:
INSTALL WINDSHIELD MOULDING
Place the moulding onto the body and tap it by hand.
16.
INSTALL THESE PARTS:
(a)
Front side of roof headlining
(b)
Roof console box
(c)
Cowl top ventilator louver
(d)
Hood to cowl top seal
(e)
Wiper arm and blades
Torque: 24 N·m (245 kgf·cm, 18 ft·lbf)
(f)
Front pillar garnishes
(g)
Sun visors and holders
BO0AH–04
N21845
N·m (kgf·cm, ft·lbf) : Specified torque
Non–reusable part
Stopper
Stopper
Back Window Moulding
Back Window Glass
Rear Seat Cushion
Rear Seatback
Roof Side
Inner Garnish
Rear Speaker Grille
Roof Side
Inner Garnish
Package Tray Trim
18 (185, 13)
–
BODY
BACK WINDOW GLASS
BO–67
1245
1997 LEXUS ES300 (RM511U)
BACK WINDOW GLASS
COMPONENTS
BO0AI–04
N21430
: 4Clips
N21407
N17178
BO–68
–
BODY
BACK WINDOW GLASS
1246
1997 LEXUS ES300 (RM511U)
REMOVAL
1.
REMOVE REAR SEAT CUSHION AND SEATBACK
(See page
)
2.
REMOVE ROOF SIDE INNER GARNISH
Remove the clip and garnish.
3.
REMOVE REAR SPEAKER GRILLE
(a)
Using a screwdriver, remove the rear speaker grille as
shown in the illustration.
HINT:
Tape the screwdriver tip before use.
(b)
Disconnect the connector.
4.
REMOVE PACKAGE TRAY TRIM
5.
REMOVE BACK WINDOW MOULDING
Using a knife, cut off the moulding as shown in the illustration.
NOTICE:
Do not damage the body with the knife.
6.
REMOVE BACK WINDOW GLASS
Remove the glass in the same way as windshield.
(See page
)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст