Lexus ES300 (1997 year). Manual — part 164
BO0BB–01
–
BODY
REAR SEAT
BO–109
1287
1997 LEXUS ES300 (RM511U)
INSTALLATION
Installation is in the reverse order of removal (See page
BO0BC–04
H02901
Adjustable Anchor
Center Pillar Garnish
Front Pillar
Garnish
Roof Side Inner Garnish
Rear Seat
Side Garnish
Lower Center
Pillar Garnish
Package Tray Trim
Belt Hole Cover
Rear Seat
Center Belt
Belt Guide
Rear Seat
Outer Belt
Anchor Cover
Front Seat Outer Belt
Rear Seat
Inner Belt
Rear Seat Inner
with Center Belt
Rear Seatback
Front Seat
Rear Seat Cushion
Front Seat
Inner Belt
: Specified torque
N·m (kgf·cm, ft·lbf)
Front Door Scuff
Inside Plate
Retractor Cover
42 (430, 31)
42 (430, 31)
7.5 (76, 66 in.·lbf)
42 (430, 31)
42 (430, 31)
18 (185, 13)
37 (375, 27)
42 (430, 31)
42 (430, 31)
42 (430, 31)
37 (375, 27)
Belt Hole
Cover
Rear Speaker Grille
37 (375, 27)
BO–110
–
BODY
SEAT BELT
1288
1997 LEXUS ES300 (RM511U)
SEAT BELT
COMPONENTS
BO0BD–04
BO0632
BO0633
15
°
45
°
–
BODY
SEAT BELT
BO–111
1289
1997 LEXUS ES300 (RM511U)
INSPECTION
CAUTION:
Replace the seat belt assembly (outer belt, inner belt, bolts,
nuts or sill–bar) if it has been used in a severe impact. The
entire assembly should be replaced even if damage is not
obvious.
1.
RUNNING TEST (IN SAFE AREA)
(a)
Fasten the front seat belts.
(b)
Drive the car at 10 mph (16 km/h) and slam on the brakes.
Check that the belt locks and cannot be extended at this
time.
HINT:
Conduct this test in a safe area. If the belt does not lock, remove
the belt mechanism assembly and conduct the following static
check. Also, whenever installing a new belt assembly, verify the
proper operation before installation.
2.
Driver’s seat belt (ELR):
STATIC TEST
(a)
Make sure that the belt locks when pulled out quickly.
(b)
Remove the locking retractor assembly.
(c)
Tilt the retractor slowly.
(d)
Make sure that the belt can be pulled out at a tilt of 15 de-
grees or less, and cannot be pulled out over 45 degrees
of tilt.
If a problem is found, replace the assembly.
3.
Except driver’s seat belt (ALR/ELR):
STATIC TEST
(a)
Make sure that the belt locks when pulled out quickly.
(b)
Remove the locking retractor assembly.
(c)
Pull out the whole belt and measure the length of the
whole belt.
Then retract the belt slightly and pull it out again
(d)
Make sure that the belt cannot be extended further.
If a problem is found, replace the assembly.
N10070
Full Belt Length Minus
200 mm (7.87 in.)
BO0633
15
°
45
°
BO–112
–
BODY
SEAT BELT
1290
1997 LEXUS ES300 (RM511U)
(e)
Retract the whole belt, then pull out the belt until 200 mm
(7.87 in.) of belt remains retracted.
(f)
Tilt the retractor slowly.
(g)
Make sure that the belt can be pulled out at a tilt of 15 de-
grees or less, and cannot be pulled out at over 45 degrees
of tilt.
If a problem is found, replace the assembly.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст