Lexus ES300 (1997 year). Manual — part 112
BE05C–03
N21362
OFF
INT
LO
HI
2
Washer ON
7
8
11
16
17
N20210
2
7
16
N20211
2
7
17
16
INT time control
switch position
FAST
SLOW
Non variable type
Voltage
Approx. 2 sec.
Battery positive voltage
0 V
Battery positive voltage
0 V
Battery positive voltage
0 V
10.7
±
5 sec.
3.3
± 1
sec.
BE–54
–
BODY ELECTRICAL
WIPER AND WASHER SYSTEM
1438
1997 LEXUS ES300 (RM511U)
INSPECTION
1.
INSPECT FRONT WIPER AND WASHER SWITCH
CONTINUITY
Switch position
Tester connection
Specified condition
OFF
7 – 16
Continuity
INT
7 – 16
Continuity
LO
7 – 17
Continuity
HI
8 – 17
Continuity
Washer ON
2 – 11
Continuity
If continuity is not as specified, replace the switch.
2.
INSPECT INTERMITTENT OPERATION
(a)
Turn the wiper switch to INT position.
(b)
Turn the intermittent time control switch to FAST position.
(c)
Connect the positive (+) lead from the battery to terminal
16 and the negative (–) lead to terminal 2.
(d)
Connect the positive (+) lead from the voltmeter to termi-
nal 7 and the negative (–) lead to terminal 2, check that
the meter needle indicates battery positive voltage.
(e)
After connecting terminal 16 to terminal 17, connect it to
terminal 2, check the voltage rises from 0 volt to battery
positive voltage within the time, as shown in the table.
If operation is not as specified, replace the wiper and washer
switch.
N20210
16
7
2
N11301
Washer Switch ON
OFF
Battery Voltage
0 V
Less than 1 sec.
Approx. 3 sec.
N21363
Wire Harness Side
1
2 3 4
5 6 7 8 9
10 11 12 13 14 15 16 17 18
N21364
1
5
–
BODY ELECTRICAL
WIPER AND WASHER SYSTEM
BE–55
1439
1997 LEXUS ES300 (RM511U)
3.
INSPECT WASHER LINKED OPERATION
(a)
Connect the positive (+) lead from the battery to terminal
16 and the negative (–) lead to terminal 2.
(b)
Connect the positive (+) lead from the voltmeter to termi-
nal 7 and the negative (–) lead to terminal 2.
(c)
Push in the washer switch, and check that the voltage
changes as shown in the table below.
If operation is not as specified, replace the wiper and washer
switch.
4.
INSPECT WIPER SWITCH CIRCUIT
Disconnect the connector from the switch and inspect the con-
nector on the wire harness side, as shown.
Tester connection
Condition
Specified condition
2 – Ground
Constant
Continuity
11 – Ground
Ignition switch LOCK or ACC
No voltage
11 – Ground
Ignition switch ON
Battery positive voltage
If circuit is not as specified, inspect the circuits connected to oth-
er parts.
5.
Low Speed:
INSPECT FRONT WIPER MOTOR OPERATION
Connect the positive (+) lead from the battery to terminal 1 and
the negative (–) lead to terminal 5, check that the motor oper-
ates at low speed.
If operation is not as specified, replace the motor.
N21365
5
4
N21366
1
5
N21367
3
5
1
2
Z10066
Wire Harness Side
1 2 3
4 5
BE–56
–
BODY ELECTRICAL
WIPER AND WASHER SYSTEM
1440
1997 LEXUS ES300 (RM511U)
6.
High Speed:
INSPECT FRONT WIPER MOTOR OPERATION
Connect the positive (+) lead from the battery to terminal 4 and
the negative (–) lead to terminal 5, check that the motor oper-
ates at high speed.
If operation is not as specified, replace the motor.
7.
Stopping at Stop Position:
INSPECT FRONT WIPER MOTOR OPERATION
(a)
Operate the motor at low speed and stop the motor opera-
tion anywhere except at the stop position by disconnect-
ing positive (+) lead from terminal 1.
(b)
Connect terminals 1 and 3.
(c)
Connect the positive (+) lead from the battery to terminal
2 and negative (–) lead to terminal 5, check that the motor
stops running at the stop position after the motor operates
again.
If operation is not as specified, replace the motor.
8.
INSPECT WIPER MOTOR CIRCUIT
Disconnect the connector from the motor and inspect the con-
nector on the wire harness side.
Tester connection
Condition
Specified condition
5 – Ground
Constant
Continuity
1 – Ground
* Wiper switch OFF or INT, HIGH
No voltage
1 – Ground
* Wiper switch LOW
Battery positive voltage
2 – Ground
Ignition switch LOCK or ACC
No voltage
2 – Ground
Ignition switch ON
Battery positive voltage
4 – Ground
* Wiper switch OFF or INT, LOW
No voltage
4 – Ground
* Wiper switch HIGH
Battery positive voltage
N21368
2
1
Z07418
Wire Harness Side
1
le–3–1–C
2 3
–
BODY ELECTRICAL
WIPER AND WASHER SYSTEM
BE–57
1441
1997 LEXUS ES300 (RM511U)
*: Turn ignition switch ON
If circuit is not as specified, inspect the circuits connected to oth-
er parts.
9.
INSPECT WASHER MOTOR OPERATION
Connect the positive (+) lead from the battery to terminal 2 and
the negative (–) lead to terminal 1, check that the motor oper-
ates.
NOTICE:
These tests must be performed quickly (within 20 seconds)
to prevent the coil from burning out.
If operation is not as specified, replace the motor.
10.
INSPECT WASHER MOTOR CIRCUIT
Disconnect the connector from the washer motor and inspect
the connector on harness side.
Tester connection
Condition
Specified condition
1 – Ground
Washer switch OFF (released)
No continuity
1 – Ground
Washer switch ON (pushed in)
Continuity
2 – Ground
Ignition switch LOCK or ACC
No voltage
2 – Ground
Ignition switch ON
Battery positive voltage
If circuit is not as specified, inspect wire harness, power source
or wiper switch.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст