Lexus ES300 (1997 year). Manual — part 524
SF060–01
SF–30
–
SFI
MASS AIR FLOW (MAF) METER
881
1997 LEXUS ES300 (RM511U)
INSTALLATION
Installation is in the reverse order of removal (See page
S04593
SF061–04
S04536
Vacuum
VTA
E2
VC
Ohmmeter
S04604
Plug
Disconnect
–
SFI
THROTTLE BODY
SF–31
882
1997 LEXUS ES300 (RM511U)
THROTTLE BODY
ON–VEHICLE INSPECTION
1.
INSPECT THROTTLE BODY
Check that the throttle linkage moves smoothly.
2.
INSPECT THROTTLE POSITION SENSOR
(a)
Apply vacuum to the throttle opener.
(b)
Disconnect the sensor connector.
(c)
Using an ohmmeter, measure the resistance between
each terminal.
Throttle valve
condition
Between
terminals
Resistance
Fully closed
VTA – E2
0.2 – 5.7 k
Ω
Fully open
VTA – E2
2.0 – 10.2 k
Ω
–
VC – E2
2.5 – 5.9 k
Ω
(d)
Reconnect the sensor connector.
3.
INSPECT THROTTLE OPENER
(a)
Allow the engine to warm up to normal operating tempera-
ture.
(b)
Check idle speed.
Idle speed: 700
±
50 rpm
(c)
Disconnect the vacuum hose from the throttle opener,
and plug the hose end.
(d)
Check the throttle opener setting speed.
Throttle opener setting speed: 900 – 1,950 rpm
If the throttle opener setting is not as specified, replace the
throttle body.
(e)
Stop the engine.
(f)
Reconnect the vacuum hose to the throttle opener.
(g)
Start the engine and check that the idle speed returns to
the correct speed.
SF062–02
S05671
EGR Gas Temperature
Sensor Bracket
Gasket
Throttle Body
Throttle Position
Sensor Connector
IAC Valve Connector
Water Bypass Hose
Air Assist Hose
Water Bypass Hose
Air Cleaner Hose
Accelerator Cable
Throttle Cable
N·m (kgf·cm, ft·lbf)
Non–reusable part
: Specified torque
19.5 (200, 14)
SF–32
–
SFI
THROTTLE BODY
883
1997 LEXUS ES300 (RM511U)
COMPONENTS
SF063–02
S05630
S06123
(3)
(1)
(a)
(b)
(2)
S04527
EGR Gas Temperature
Sensor Bracket
–
SFI
THROTTLE BODY
SF–33
884
1997 LEXUS ES300 (RM511U)
REMOVAL
1.
DRAIN ENGINE COOLANT
2.
DISCONNECT ACCELERATOR CABLE
3.
DISCONNECT THROTTLE CABLE
4.
REMOVE AIR CLEANER HOSE
(a)
Disconnect the PCV hose.
(b)
Loosen the 2 hose clamps, and remove the air cleaner
hose.
5.
REMOVE THROTTLE BODY
(a)
Disconnect the throttle position sensor connector.
(b)
Disconnect the IAC valve connector.
(c)
Disconnect these hoses:
(1)
Water bypass hose (from intake manifold)
(2)
Water bypass hose (from water inlet housing)
(3)
Air assist hose
(d)
Remove the 2 bolts, 2 nuts, EGR gas temperature sensor
bracket, throttle body and gasket.
HINT:
At the time of installation, please refer to the following item.
Place a new gasket on the air intake chamber.
Torque: 19.5 N·m (200 kgf·cm, 14 ft·lbf)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст