Lexus ES300 (1997 year). Manual — part 342
A00307
ON
VSV is ON
VSV is OFF
Air Filter
Air
Air
E
F
E
F
BE6653
FI7073 FI7074
–
DIAGNOSTICS
ENGINE
DI–145
297
1997 LEXUS ES300 (RM511U)
INSPECTION PROCEDURE
LEXUS hand–held tester
1
Connect LEXUS hand–held tester and check operation of VSV for ACIS.
PREPARATION:
(a)
Remove the fuse cover on the instrument panel.
(b)
Connect the LEXUS hand–held tester to the DLC3.
(c)
Turn ignition switch ON and LEXUS hand–held tester
main switch ON.
(d)
Select the ACTIVE TEST mode on the LEXUS hand–held
tester.
CHECK:
Check operation of VSV when VSV is operated by the LEXUS
hand–held tester.
OK:
VSV is ON:
Air from pipe E is flowing out through pipe F.
VSV is OFF:
Air from pipe E is flowing out through the air filter.
OK
Check for vacuum tank (See page
NG
2
Check VSV for ACIS (See page
NG
Replace VSV for ACIS.
OK
A00308
ON
ACIS(+)
BE6653
P23894
DI–146
–
DIAGNOSTICS
ENGINE
298
1997 LEXUS ES300 (RM511U)
3
Check for open and short in harness and connector between EFI main relay
(Marking: EFI) and ECM (See page
).
NG
Repair or replace harness or connector.
OK
Check and replace ECM (See page
).
OBD II scan tool (excluding LEXUS hand–held tester)
1
Check VSV for ACIS (See page
NG
Replace VSV for ACIS.
OK
2
Check voltage between terminal ACIS of ECM connector and body ground.
PREPARATION:
(a)
Remove the glove compartment (See page
).
(b)
Turn ignition switch ON.
CHECK:
Measure voltage between terminal ACIS of ECM connector and
body ground.
OK:
Voltage: 9
∼
14 V
NG
Check for open and short in harness and
connector between EFI main relay and ECM
(See page
).
OK
–
DIAGNOSTICS
ENGINE
DI–147
299
1997 LEXUS ES300 (RM511U)
3
Check for vacuum tank (See page
NG
Repair or replace.
OK
Check and replace ECM (See page
).
DI0C9–01
Vehicle Brought to Workshop
Customer Problem Analysis
Check DTC and Freezes Frame Data (Precheck)
Record or Print DTC and Freezed Frame Data P.
Clear DTC and Freezed Frame Data P.
Visual Inspection
Setting the Check Mode Diagnosis P.
1
Items inside
are titles of pages in this manual, with the
page number indicated in the bottom portion. See the indicated
pages for detailed explanations.
Connect an OBD II scan tool or LEXUS hand–held tester to DLC3.
If the display shows ”UNABLE TO CONNECT TO VEHICLE” when you have connected the
scan tool / LEXUS hand–held tester, inspect DLC3 P.
2
3
4
5
6
symptom does not occur
Problem Symptom Confirmation
8
7
Symptom Simulation
P.
symptom occur
DTC Check
OK Code
11
Preliminary Check
DTC Chart
P.
Mechanical System Test
Manual Shifting Test
OK
OK
Chapter 1
(Electronic)
Chapter 2
(On–Vehicle)
P.
OK
Chapter 3
(Off–Vehicle)
OK
Matrix Chart of Problem Symptoms –
P.
Circuit
Inspection
Main Throttle Signal Check
Stop Light Signal Check
NG
Parts Inspection
NG
NG
NG
Identification of Problem
Repair
Confirmation Test
End
NG
NG
12
NG
13
14
15
16
17
9
10
P.
P.
P.
DI–148
–
DIAGNOSTICS
AUTOMATIC TRANSAXLE
300
1997 LEXUS ES300 (RM511U)
AUTOMATIC TRANSAXLE
HOW TO PROCEED WITH TROUBLESHOOTING
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст