Lexus NX350h (2022 year). Manual in english — page 10
●
If the driver’s door is opened and all of the following conditions are met, while the shift
position is in a position other than P
•
The power switch is in ON.
•
The driver is not wearing the seat belt.
•
The brake pedal is not depressed.
To start off the vehicle after the shift position is changed to P, operate the shift lever
again.
●
When the vehicle is stopped after the hybrid system has been stopped in an emergen-
cy while driving.
●
When voltage of the 12-volt battery drops while the shift position is in a position other
than P.
■
If the shift position cannot be shifted from P
There is a possibility that the 12-volt battery is discharged. Check the 12-volt battery in
this situation.
WARNING
■
For the shift lever
●
Do not remove the shift lever knob or use anything but a genuine Lexus shift lever
knob. Also, do not hang anything on the shift lever. Doing so could prevent the shift
lever from returning to position, causing unexpected accidents to occur when the
vehicle is in motion.
●
In order to prevent the shift position from accidentally being changed, do not touch the
shift lever when not using them.
■
P position switch
●
Do not press the P position switch while the vehicle is moving.
If the P position switch is pressed when driving at very low speeds (for example,
directly before stopping the vehicle), the vehicle may stop suddenly when the shift
position switches to P, which could lead to an accident.
●
In order to prevent the shift position from accidentally being changed, do not touch the
P position switch when not using them.
*1 :
When the power switch is pressed while driving at extremely slow speeds, such as
immediately before stopping the vehicle, the shift position may automatically change
to P. Make sure that the vehicle is completely stopped before pressing the power
switch.
2-2. Driving procedures
169
2
Driving the v
ehicle
NOTICE
■
Notes regarding shift lever and P position switch operation
Avoid repeatedly operating the shift lever and P position switch in quick succession. The
system protection function may activate and it will not be temporarily possible to shift the
shift position other than P. If this happens, please wait for a while before attempting to
change the shift position again.
■
When exiting the vehicle(driver's seat only)
Check that the shift position indicator shows P and that the parking brake indicator is
illuminated before opening the door and exiting the vehicle.
When the power switch is changed to ACC with the shift position held in
N
Performing the following operations allows the power switch to be set to ACC with
the shift position held in N.
1
Operate the shift lever and change the shift position to N when the hybrid
system is operating.
2
Return the shift lever to its regular position (
●
).
3
Operate the shift lever to N and hold it there until the buzzer sounds.
4
Press the power switch within 5 seconds after the buzzer sounds.
Make sure to check that the buzzer sounds and "Holding N Push P Switch When
Done" is displayed on the multi-information display.
●
To change to a shift position other than N, press the P position switch. The shift
position will be changed to P.
●
Even if the hybrid system is not operating, by operating the shift lever and the power
switch, the power switch may be changed to ACC with the shift position held in N.
Make sure that the hybrid system is operating before performing the operation.
2-2. Driving procedures
170
Starting off
1
With the brake pedal depressed, shift the shift position to D.
Check that the shift position indicator shows D.
WARNING
Always keep your foot on the brake pedal while stopped with the "READY" indicator
is illuminated. This prevents the vehicle from creeping.
2
If the parking brake is set, release the parking brake.
3
Gradually release the brake pedal and gently depress the accelerator pedal to
accelerate the vehicle.
Related Links
Manual applying/releasing of the parking brake (manual mode)(P. 181)
Starting off on an incline
1
Firmly depress the brake pedal and shift the shift position to D.
The hill-start assist control will be activated.
WARNING
Always keep your foot on the brake pedal while stopped with the "READY" indicator
is illuminated. This prevents the vehicle from creeping.
2
Set the parking brake.
3
Release the brake pedal and gently depress the accelerator pedal to acceler-
ate the vehicle.
4
Release the parking brake.
Related Links
Manual applying/releasing of the parking brake (manual mode)(P. 181)
2-2. Driving procedures
171
2
Driving the v
ehicle
Operations when turning left or right or changing lanes
By operating the turn signal lever, the intent of the driver can be shown as follows.
INFORMATION
●
The turn signal lights can be operated when the power switch is in ON.
●
If the indicator flashes faster than usual, check that a light bulb in the front or rear turn
signal lights has not burned out.
1
Move the lever to position
.
The right turn signal lights will blink.
2
Move the lever to position
and release it.
The right hand signals will flash 3 times.
3
Move the lever to position
and release it.
The left hand signals will flash 3 times.
4
Move the lever to position
The left turn signal lights will blink.
2-2. Driving procedures
172
Changing the shift range
The shift range can be changed by operating the paddle shift switches. Changing
the shift range enables the level of engine braking force to be selected.
Selecting shift ranges in the D position
To drive using temporary shift range selection, operate the [-] paddle shift switch
with the shift position in D.
The shift range can then be selected by operating the [-] and [+] paddle shift
switches.
1
Upshift
2
Downshift
The selected shift range, from D1 to D6, will be displayed on the multi-information
display.
To return to normal D position driving, hold the [+] paddle shift switch for a certain
amount of time.
●
Shift ranges and their functions
•
You can choose from 6 levels of engine braking force.
•
A lower shift range will provide greater engine braking force than a shift range. As a
result, the engine speed will increase.
INFORMATION
■
Automatic deactivation of shift range selection in the D position
Shift range selection in the D position will be deactivated in the following situations:
●
When the vehicle comes to a stop
●
If the accelerator pedal is depressed for more than a certain period of time
●
When the shift position is shifted to a position other than D
■
Downshifting restriction warning buzzer
To help ensure safety and driving performance, downshift operations may be restricted.
In some circumstances, downshifting may not be possible even when the paddle shift
switch is operated. (A buzzer will sound twice.)
2-2. Driving procedures
173
2
Driving the v
ehicle
Selecting shift ranges in the S position
To enter S mode, change the shift position to S.
The shift range can be selected by operating the [-] and [+] paddle shift switches.
1
Upshift
2
Downshift
The selected shift range, from S1 to S6, will be displayed on the multi-information
display.
The initial shift range in S position is set automatically to S4 or S5 according to
vehicle speed.
●
Shift ranges and their functions
•
You can choose from 6 levels of accelerating force and engine braking force.
•
A lower shift range will provide greater accelerating force and engine braking force
than a higher shift range, and the engine revolutions will also increase.
INFORMATION
■
S mode
●
To prevent the engine from over-revving, upshifting may automatically occur when the
shift range is S4 or lower.
●
When in S4 or lower, if the paddle shift switch is held toward [
+
] the shift range will be
set to S6.
■
Downshifting restriction warning buzzer
To help ensure safety and driving performance, downshift operations may be restricted.
In some circumstances, downshifting may not be possible even when the paddle shift
switch is operated. (A buzzer will sound twice.)
■
If the "S" indicator does not come on or the "D" indicator is displayed even after
changing the shift position to S position
This may indicate a malfunction in the hybrid transmission system. Have the vehicle
inspected by your Lexus dealer immediately. (In this situation, the hybrid transmission will
operate in the same manner as when the shift position is in D.)
2-2. Driving procedures
174
Parking the vehicle
When parking the vehicle
Precautions for when the vehicle is stopped or parked
WARNING
■
When the vehicle is parked
●
Always apply the parking brake, shift the shift position to P, stop the hybrid system and
lock the vehicle. Do not leave the vehicle unattended while the "READY" indicator is
illuminated.
If the vehicle is parked with the shift position in P but the parking brake is not set, the
vehicle may start to move, possibly leading to an accident.
●
Never leave a child unattended in the vehicle. A child may accidentally release the
parking brake and the vehicle may move, possibly leading to an accident.
●
Do not leave glasses, cigarette lighters, spray cans or carbonated drink cans in the
vehicle when it is parked in the sun. If left in the vehicle, the following may occur:
•
Gas may leak from a cigarette lighter or spray can, and may lead to a fire.
•
The temperature inside the vehicle may cause the plastic lenses and plastic material
of glasses to deform or crack.
•
Soft drink cans may explode, dirtying the interior and possibly causing a short in
electronic components.
●
Do not store cigarette lighters in the vehicle storage features or leave them inside the
vehicle.
When luggage is loaded or a seat is adjusted, a lighter may be unintentionally lit,
possibly leading to a fire.
●
Do not attach suction cups to the glass parts of the vehicle. Also, do not place air
fresheners or other clear containers on the instrument panel or dashboard. Suction
cups and clear containers may act as a lens, possibly leading to a fire inside the vehicle.
●
Do not leave a door or window open if the curved glass is coated with a metallized film
such as a silver-colored one.
Reflected sunlight may cause the glass to act as a lens, causing a fire.
●
Do not touch the exhaust pipes while the "READY" indicator is illuminated or immedi-
ately after turning the hybrid system off. Doing so may cause burns.
■
When taking a nap in the vehicle
Always turn the hybrid system off. If the "READY" indicator remains illuminated while
taking a nap, you may unintentionally operate the shift lever or accelerator pedal, possibly
leading to an accident or a fire from the hybrid system overheating. Additionally, if the
vehicle is parked in a poorly ventilated area, exhaust gases may accumulate and enter the
vehicle.
2-3. Parking the vehicle
175
2
Driving the v
ehicle
Exhaust gas precautions
Harmful substance to the human body is contained in exhaust gases if inhaled.
WARNING
Exhaust gases contain harmful carbon monoxide (CO), which is colorless and odorless.
Observe the following precautions.
Failure to do so may cause exhaust gases to enter the vehicle. This may cause light-head-
edness, possibly leading to an accident, death or a serious health hazard.
●
Keep the back door closed while driving.
If you smell exhaust gases in the vehicle even when the back door is closed, open the
windows and have the vehicle inspected by your Lexus dealer as soon as possible.
●
If the vehicle is in a poorly ventilated area or a closed area, such as a garage, stop the
hybrid system.
●
Do not leave the vehicle with the hybrid system on for a long time. If such a situation
cannot be avoided, park the vehicle in an open space and ensure that exhaust fumes
do not enter the vehicle interior.
●
Do not leave the hybrid system operating in an area with snow build-up, or where
it is snowing. If snowbanks build up around the vehicle while the hybrid system is
operating, exhaust gases may collect and enter the vehicle.
●
The exhaust system needs to be checked periodically. Check for the following. If any
are found, have the vehicle inspected by your Lexus dealer.
•
Holes or cracks in the exhaust pipes due to corrosion
•
Damage at the joining parts of the exhaust pipes
•
Abnormal noise from the exhaust
2-3. Parking the vehicle
176
Stopping
1
Depress the brake pedal.
WARNING
●
Drive more carefully than normal when the brakes are wet. When the brakes are
wet, the braking distance will increase. Also, the brakes will be difficult to apply
and, depending on the situation, braking performance may differ between the left
and right sides. Additionally, the parking brake may not be able to be securely
applied.
●
If the electronically controlled brake system does not operate, do not follow other
vehicles closely and avoid hills or sharp turns that require braking.In this case,
braking is still possible, but the brake pedal should be depressed more firmly than
usual. Also, the braking distance will increase. Have your brakes fixed immediately.
●
If the brake hydraulic system malfunctions, have it repaired immediately. The brake
system consists of 2 or more independent systems and if 1 hydraulic system fails,
the other systems will operate. In this situation, it will be necessary to depress the
brake pedal more than normal and braking distance will be increased.
NOTICE
Do not use the accelerator pedal or depress the accelerator and brake pedals at the
same time to hold the vehicle on a hill.
2
If necessary, set the parking brake.
If the vehicle is to be stopped for an extended period of time, shift the shift position to P.
WARNING
■
When the vehicle is stopped
●
Do not depress the accelerator pedal unnecessarily.
If the vehicle is in any gear other than P or N, the vehicle may accelerate suddenly
and unexpectedly, causing an accident.
●
In order to prevent accidents due to the vehicle rolling away, always keep depress-
ing the brake pedal while stopped with the "READY" indicator is illuminated, and
apply the parking brake as necessary.
●
If the vehicle is stopped on an incline, in order to prevent accidents caused by the
vehicle rolling forward or backward, always depress the brake pedal and securely
apply the parking brake as needed.
●
Avoid revving or racing the engine. Running the engine at high speed while the
vehicle is stopped may cause the exhaust system to overheat, which could result in
a fire if combustible material is nearby.
2-3. Parking the vehicle
177
2
Driving the v
ehicle
Parking the vehicle
1
Depress the brake pedal to stop the vehicle completely.
2
If the parking brake is released, set the parking brake.
3
Shift the shift position to P.
Check that the shift position indicator shows P and the parking brake indicator is
illuminated.
WARNING
Always set the parking brake, and shift the shift position to P. Failure to do so may
cause the vehicle to move or the vehicle may accelerate suddenly if the accelerator
pedal is accidentally depressed.
4
Press the power switch to stop the hybrid system.
5
Slowly release the brake pedal.
6
Lock the door, making sure that you have the electronic key on your person.
If parking on a hill, block the wheels as needed.
Related Links
Parking brake operation
The parking brake can be applied or released automatically (automatic mode)
or manually (manual mode). In automatic mode, the parking brake is applied
or released automatically according to the operation of the shift lever. Also, in
automatic mode the parking brake can be applied or released manually.
WARNING
■
When parking the vehicle
Do not leave a child in the vehicle alone. The parking brake may be released unintention-
ally by a child and there is the danger of the vehicle moving that may lead to an accident
resulting in death or serious injury.
■
Parking brake switch
Do not set any objects near the parking brake switch. Objects may interfere with the
switch and may lead the parking brake to unexpectedly operate.
2-3. Parking the vehicle
179
2
Driving the v
ehicle
NOTICE
■
When the vehicle is parked
●
Always apply the parking brake, shift the shift position to P, stop the hybrid system and
lock the vehicle. Do not leave the vehicle unattended while the "READY" indicator is
illuminated.
If the vehicle is parked with the shift position in P but the parking brake is not set, the
vehicle may start to move, possibly leading to an accident.
■
When the system malfunctions
Stop the vehicle in a safe place and check the warning messages.
■
When the vehicle 12-volt battery is discharged
The parking brake system cannot be activated.
■
When the parking brake cannot be released due to a malfunction
Driving the vehicle with the parking brake set will lead to brake components overheating,
which may affect braking performance and increase brake wear. Have the vehicle
inspected by your Lexus dealer a immediately if this occurs.
INFORMATION
■
Parking brake automatic release function
When all of the following conditions are met, the parking brake can be released by
depressing the accelerator pedal.
●
The driver’s door is closed
●
The driver is wearing the seat belt
●
The shift lever is in a forward driving position or reverse driving position
●
The malfunction indicator lamp and brake system warning light are not illuminated
When depressing the accelerator pedal, depress it slowly. If the parking brake is not
released when the accelerator pedal is depressed, release the parking brake manually.
Automatic mode: When the shift position is shifted from P, the parking brake will be
released automatically.
■
Parking brake operation sound
When the parking brake operates, a motor sound (whirring sound) may be heard. This
does not indicate a malfunction.
■
Parking brake indicator light
●
Depending on the power switch mode, the parking brake indicator light will turn on
and stay on as described below:
ON: Comes on until the parking brake is released.
2-3. Parking the vehicle
180
Not in ON: Stays on for approximately 15 seconds.
●
When the power switch is turned off with the parking brake set, the parking brake
indicator light will stay on for about 15 seconds. This does not indicate a malfunction.
■
When the parking brake switch malfunctions
Automatic mode (automatic brake setting and releasing) will be turned on automatically.
■
Parking brake engaged warning buzzer
A buzzer will sound if the vehicle is driven with the parking brake engaged. "Parking
Brake ON" is displayed on the multi-information display (with the vehicle reaching a
speed of 3 mph [5 km/h]).
Automatic applying/releasing of the parking brake (auto mode)
While the vehicle is stopped, pull and hold the parking brake switch until "EPB Shift
Interlock Function Activated" will be displayed on the multi-information display.
When the automatic mode is turned on, the parking brake operates as follows.
●
When the shift position is shifted from P: The parking brake will be released, and
the parking brake indicator light will turn off.
●
When the shift position is shifted to P: The parking brake will be set, and the
parking brake indicator light will turn on.
Operate the shift lever with the brake pedal depressed.
The auto function may not operate if the shift lever is moved extremely quickly. In
this situation, apply the parking brake manually.
With the vehicle stopped, press and hold the parking brake switch until a buzzer
sounds and "EPB Shift Interlock Function Deactivated" is displayed. Automatic
mode will be turned off.
INFORMATION
■
Parking brake operation
●
When the power switch is not in ON, the parking brake cannot be released using the
parking brake switch.
●
When the power switch is not in ON, automatic mode (automatic brake setting and
releasing) is not available.
Manual applying/releasing of the parking brake (manual mode)
The parking brake can be set and released manually.
2-3. Parking the vehicle
181
2
Driving the v
ehicle
A
Parking brake indicator (U.S.A.)
B
Parking brake indicator (Canada)
1
Pull the switch to set the parking brake.
The parking brake indicator light will turn on.
Pull and hold the parking brake switch if an emergency occurs and it is necessary to
operate the parking brake while driving.
2
Press the switch to release the parking brake.
●
Operate the parking brake switch while depressing the brake pedal.
●
The parking brake can be released by depressing the accelerator pedal,
through the parking brake automatic release function.
Parking brake automatic release function
Make sure that the parking brake indicator light and the parking brake switch
indicator turn off.
If the parking brake indicator light flash, operate the switch again.
Garage door opener and its performance
The garage door opener can be programmed using the HomeLink
®
to operate
garage doors, gates, entry doors, door locks, home lighting systems, security
systems, and other devices.
INFORMATION
■
HomeLink
®
programming procedure
The programming procedures can also be found at the following URL.
2-3. Parking the vehicle
182
Website:
For support, contact customer support at the follow-
ing.
Help Line: 1-800-355-3515
System components
The HomeLink
®
wireless control system in your vehicle has 3 buttons which can
be programmed to operate 3 different devices.
▶
Vehicles with auto anti-glare inside rear view mirror
A
HomeLink
®
indicator light
B
Garage door operation indicators
C
HomeLink
®
icon
Illuminates while HomeLink
®
is operating.
D
Buttons
▶
Vehicles with Digital Rearview Mirror
A
HomeLink
®
logo
Appears while HomeLink
®
is operating. When
the menu button is pressed, the logo disappears
even while the HomeLink
®
is operating.
B
Garage door operation indicators
C
HomeLink
®
indicator lights
Illuminates above each button selected.
D
Buttons
WARNING
Do not use the HomeLink
®
compatible transceiver with any garage door opener or
device that lacks safety stop and reverse features as required by federal safety standards.
This includes any garage door that cannot detect an interfering object. A door or device
without these features increases the risk of death or serious injury.
2-3. Parking the vehicle
183
2
Driving the v
ehicle
INFORMATION
■
Codes stored in the HomeLink
®
memory
●
The registered codes are not erased even if the 12-volt battery cable is disconnected.
●
If learning fails when registeing a code to a previously registered HomeLink
®
button,
the registered code will not be erased.
Program the HomeLink
®
Before programming the HomeLink
®
, perform the following:
●
During programming, it is possible that garage doors, gates, or other devices
may operate. For this reason, make sure that people and objects are clear of the
garage door or other devices to prevent injury or other potential harm.
●
It is recommended that a new battery be placed in the remote control transmit-
ter for more accurate programming.
The battery side of the transmitter must be pointed away from the HomeLink
®
buttons.
●
Garage door opener motors manufactured after 1995 may be equipped with
rolling code protection. If this is the case, you may need a stepladder or other
sturdy, safe device to reach the “learn” or “smart” button on the garage door
opener motor.
WARNING
●
The garage door or other device may operate, so ensure people and objects are out
of danger to prevent potential harm.
●
Never allow a child to operate or play with the HomeLink
®
buttons.
Steps
must be performed within 60 seconds. Otherwise the indicator
light will stop flashing and programming will not be able to be completed.
1
Press and release the HomeLink
®
button you want to program and check that
the HomeLink
®
indicator light flashes orange.
2-3. Parking the vehicle
184
2
Point the remote control transmitter for the
device at the rear view mirror, 1 to 3 in. (25 to
75 mm) from the HomeLink
®
buttons.
Keep the HomeLink
®
indicator light in view while
programming.
3
Program a device.
●
Programming a device other than an entry gate (for U.S.A. owners):
▶
Vehicles with auto anti-glare
inside rear view mirror
▶
Vehicles with Digital Rearview
Mirror
▶
Vehicles with auto anti-glare
inside rear view mirror
▶
Vehicles with Digital Rearview
Mirror
2-3. Parking the vehicle
185
2
Driving the v
ehicle
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст