Lexus SC300 / Lexus SC400. Manual — part 121
11. INSTALL FRONT PILLAR GARNISH
(a) Insert front side of the garnish to the pillar to install the
clip.
(b) Install the garnish by tapping.
(c) Install two screws and the assist grip.
12. INSTALL ASSIST GRIP
BO–126
–
BODY
Trim, Assist Grip and Visor
BODY DIMENSIONS
Description
1. BASIC
DIMENSIONS
(a) There are two types of dimensions in the diagram.
(Three–dimensional distance)
•
Straight–line distance between the centers of two
measuring points.
(Two–dimensional distance)
•
Horizontal distance in forward/rearward between the
centers of two measuring points.
•
The height from an imaginary standard line.
(b) In cases in which only one dimension is given, left and
right are symmetrical.
(c) The dimensions in the following drawing indicate actual
distance. Therefore, please use the dimensions as a
reference.
2. MEASURING
(a) Basically, all measurements are to be done with a
tracking gauge. For portions where it is not possible to
use a tracking gauge, a tape measure should be used.
(b) Use only a tracking gauge that has no looseness in the
body, measuring plate, or pointers.
HINT:
1.
The height of the left and right pointers must be equal.
2.
Always calibrate the tracking gauge before measuring
or after adjusting the pointer height.
3.
Take care not to drop the tracking gauge or otherwise
shock it.
4.
Confirm that the pointers are securely in the holes.
(c) When using a tape measure, avoid twists and bends in
the tape.
(d) When tracking a diagonal measurement from the front
spring support inner hole to the suspension member
upper rear installation hole, measure along the front
spring support panel surface.
–
BODY
Body Dimensions (Description)
BO–127
Body Dimension Drawings
ENGINE COMPARTMENT
(Three–Dimensional Distance)
mm (in.)
B06846
B06860
Symble
Name
Hole dia.
Symble
Name
Hole dia.
A,a
Front fender apron standard hole
10 (0.39)
L,l
Front fender installation nut
6 (0.24) screw
B,b
Front spring support hole – front
11 (0.43)
M,n
Hood hinge installation nut – rear
8 (0.31) screw
C,c
Cowl side panel standard hole
10 (0.39)
N,n
Front fender installation nut – rear
6 (0.24) screw
D
Cowl top panel center mark
O,o
Headlight installation nut
6 (0.24) screw
E,e
Front side member working hole
18 (0.71)
P,p
Headlight installation nut
6 (0.24) screw
F,f
Front side member working hole
18 (0.71)
Q,q
Headlight installation nut
6 (0.24) screw
G,g
Radiator support standard hole
10 (0.39)
R,r
Headlight installation nut
6 (0.24) screw
H,h
Radiator support standard hole
10 (0.39)
S,s
Headlight installation hole
11 (0.43)
I,i
Front fender apron standard hole
10 (0.39)
T,t
Headlight installation hole
10 (0.39)
J,j
Front side member standard hole
8 (0.31)
U,u
Headlight installation hole
10 (0.39)
K,k
Front fender installation nut – front
6 (0.24) screw
BO–128
–
BODY
Body Dimensions (Body Dimension Drawings)
UNDER BODY
(Three–Dimensional Distance)
–
BODY
Body Dimensions (Body Dimension Drawings)
BO–129
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст