Lexus SC300 / Lexus SC400. Manual — part 494
9. INSPECT
HEATER
RESISTANCE OF SUB–OXYGEN
SENSORS
Using an ohmmeter, measure the resistance between the ter-
minals +B and HT.
Resistance: 5.1–6.3
at 20
°
C (68
°
F)
If the resistance is not as specified, replace the sensor as
follows:
•
Disconnect the grommet from the floor panel, and
pull out the wire of the sub–oxygen sensor from the
floor panel.
•
Remove the sub–oxygen sensor.
•
Install a new sub–oxygen sensor.
Torque: 44 N
⋅
m (450 kgf
⋅
cm, 33 ft
⋅
lbf)
•
Run the wire of the sub–oxygen sensor through the
hole in the floor panel.
10. RECONNECT SUB–OXYGEN SENSOR CONNECTORS
11. REINSTALL
RADIO
(a) Connect the wiring connectors and antenna cable.
(b) Install the radio with the five bolts.
12. REINSTALL UPPER REAR CONSOLE PANEL
(a) Fit the console panel to the console box with five clips.
(b) Install the console panel with the six screws.
FI–120
EFI SYSTEM – Electronic Control System (Sub–Oxygen Sensors)
13. REINSTALL UPPER CONSOLE PANEL
Fit the console panel to the console box with the four clips.
14. REINSTALL CUP HOLDER
Fit the cup holder to the console box.
15. REINSTALL TRANSMISSION SHIFT LEVER KNOB
(a) Slide the lever cover on the lever shaft.
(b) Install the shift lever knob with the two screws.
(c) Attach the lever cover to the lower side of the lever knob.
16. RECONNECT CABLE TO NEGATIVE TERMINAL OF
BATTERY
FI–121
EFI SYSTEM – Electronic Control System (Sub–Oxygen Sensors)
Preparation
SST (SPECIAL SERVICE TOOLS)
Illustration
Part No.
Part Name
Note
09268–41045
Injection Measuring
Tool Set
(90268–41070)
No. 4 Union
Injector
(09268–41080)
No. 6 Union
Cold start Injector
(09268–52010)
Injection Measuring
Attachment
Injector
09268–45012
EFI Fuel Pressure
Gauge
09612–24014
Steering Gear
Housing Overhaul
Tool Set
(09617–24011)
Steering Rack Wrench
Fuel pressure pulsation damper
09631–22020
Power Steering
Hose Nut 14 X 17 mm
Wrench Set
Fuel line flare nut
09816–30010
Oil Pressure
Switch Socket
Knock sensor
09842–30055
Wire “G”
EFI Inspection
Cold start Injector
09842–30070
Wire “F”
EFI Inspection
Injector
09843–18020
Diagnosis Check
Wire
0990–01000
Engine Control
Computer
Check Harness “A”
FI–10
– Preparation
EFI SYSTEM
RECOMMENDED TOOLS
Illustration
Part No.
Part Name
Note
09082–0015
TOYOTA
Electrical Tester
09200–00010
Engine Adjust
Kit
09258–00030
Hose Plug Set
Plug for the Vacuum hose, fuel hose ect.
EQUIPMENT
Part Name
Note
Graduated cylinder
Injector
Tachometer
Torque wrench
SSM (SERVICE SPECIAL MATERIALS)
Part Name
Part No.
Use etc.
Seal packing 1282B,
08826–00100
Water inlet housing
Three bond 1282B or equivalent
FI–11
EFI SYSTEM – Preparation
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст