Lexus SC300 / Lexus SC400. Manual — part 364
(c) Remove the bolt, 2 nuts, the EGR valve, vacuum modulator
assembly and gasket.
14. REMOVE EGR VALVE ADAPTOR
(a) Disconnect the EGR gas temperature sensor connector.
(b) Disconnect the PCV hose from the cylinder head.
(c) Remove the 2 bolts, 2 nuts, EGR adaptor and gasket.
15. REMOVE IAC VALVE
(a) Disconnect the IAC valve connector.
(b) Disconnect the water bypass hose from the IAC valve.
(c) Remove the 2 nuts, IAC valve and gasket.
–
1UZ–FE ENGINE
ENGINE MECHANICAL
EG–79
16. REMOVE HEATER WATER VALVE FROM BODY
(a) Disconnect the VSV connector.
(b) Disconnect the bolt holding the engine wire clamp to the
water valve bracket.
(c) Remove the 2 bolts, and disconnect the water valve and
bracket assembly.
17. REMOVE THROTTLE BODY
(a) Disconnect the following connectors:
(1) Throttle position sensor connector
(2) w/
TRAC:
Sub–throttle position sensor connector
(3) w/
TRAC:
Sub–throttle actuator connector
(b) Remove the 2 bolts and 2 nuts, and disconnect the throttle
body from the air intake chamber.
(c) Disconnect the following hoses, and remove the throttle
body:
(1) PCV hose from throttle body
(2) Water bypass hose from throttle body
(d) Remove the throttle body gasket.
18. REMOVE AIR INTAKE CHAMBER
(a) Disconnect the following hoses:
(1) Brake booster vacuum hose from union on air intake
chamber
(2) Vacuum
hose (from VSV for heater water valve) from air
intake chamber
EG–80
–
1UZ–FE ENGINE
ENGINE MECHANICAL
(b) Remove the bolt, stud bolt and accelerator bracket.
(c) Remove the union bolt, union and 2 gaskets.
(d) Disconnect the following connectors:
•
Cold start injector connector
•
VSV connector for fuel pressure control
•
Except California:
VSV connector for EGR
(e) Remove the union bolt and 2 gaskets, and disconnect the
cold start injector tube from the RH delivery pipe.
CAUTION:
•
Put a shop towel under the delivery pipe.
•
Slowly loosen the union bolt.
(f) Remove the 2 bolts and gasket, and disconnect the EGR
pipe from the air intake chamber.
(g) Remove the 4 bolts, 8 nut and following parts:
(1) VSV for fuel pressure
(2) Except
California:
VSV for EGR
(3) Transmission throttle cable bracket
(h) Disconnect the DLC1 from the air intake chamber.
(i)
Remove the air intake chamber and 4 gaskets.
–
1UZ–FE ENGINE
ENGINE MECHANICAL
EG–81
(j)
Remove the 3 bolts, the cold start injector, tube, lead wire
assembly and gasket.
19. DISCONNECT
HEATER
WATER
HOSES
Disconnect the following hoses:
(1) Water hose from water bypass pipe
(2) Water hose from rear water bypass joint
20. DISCONNECT
FUEL INLET HOSE FROM DELIVERY PIPE
Remove the pulsation damper and 2 gaskets, and discon-
nect the fuel inlet hose from the delivery pipe.
CAUTION:
•
Put a shop towel under the delivery pipe.
•
Slowly loosen the union bolts.
21. DISCONNECT FUEL RETURN HOSE FROM FUEL
RETURN PIPE
22. DISCONNECT EGR PIPE FROM RH CYLINDER HEAD
Remove the bolt holding the EGR pipe to the RH cylinder
head, and disconnect the EGR pipe.
23. DISCONNECT ENGINE WIRE FROM INTAKE MANIFOLD
Remove the 2 bolts, and disconnect the engine wire protector
from the intake manifold.
EG–82
–
1UZ–FE ENGINE
ENGINE MECHANICAL
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст