Lexus SC300 / Lexus SC400. Manual — part 393
11. CONNECT ENGINE WIRE TO CABIN
(a) Push in the engine wire through the cowl panel.
NOTICE: Be careful not to damage the engine wire. Tape
the engine wire.
(b) Install the engine wire retainer with the 3 bolts.
(c) Connect the following connectors:
(1) 2 connectors to ECM
(2) Connector to ABS & TRAC ECU
(3) 2 connectors to TRAC ECU
(4) 4 connectors to connector cassette
(5) Connector to A/C control assembly
–
1UZ–FE ENGINE
ENGINE MECHANICAL
EG–195
(d) Install the ECM with the nut.
(e) Install the ECM protector with the 2 nuts.
(f) Install the floor carpet.
(g) Install the scuff plate.
(h) Connect the connectors.
(i) Install the lower instrument panel finish panel and glove
compartment door assembly with the 4 screws.
(j)
Install the instrument panel under cover with the 2 clips.
EG–196
–
1UZ–FE ENGINE
ENGINE MECHANICAL
12. INSTALL CHARCOAL CANISTER
(a) Install the charcoal canister.
(b) Connect the vacuum hose and air hose to the charcoal
canister.
13. CONNECT HOSES
Connect the following hoses and ground strap:
(1)
Heater water hose to water bypass hose
(2)
Heater water hose to heater water valve
(3)
Brake booster hose to union on air intake chamber
(4)
Vacuum hose (from VSV for heater water valve) to air in-
take chamber
(5)
Ground strap to bracket on body
(6)
Fuel inlet hose to fuel tube
SST 09278–54012
Torque: 30 N
⋅
m (310 kgf
⋅
cm, 22 ft
⋅
lbf)
HINT: Use a torque wrench with a fulcrum length of 30 cm
(11.81 in.).
(7)
Fuel return hose to return pipe
14. INSTALL AIR CONDITIONING (A/C) COMPRESSOR
(a) Install the A/C compressor, compressor stay and ground
cable with the nut and 3 bolts.
Torque:
49 N
⋅
m (500 kgf
⋅
cm, 36 ft
⋅
lbf) for bolt
29 N
⋅
m (300 kgf
⋅
cm, 22 ft
⋅
lbf) for nut
(b) Connect the A/C compressor connector.
–
1UZ–FE ENGINE
ENGINE MECHANICAL
EG–197
15. INSTALL POWER STEERING (PS) PUMP
(a) Install the PS pump with the nut and 3 bolts. Alternately
tighten the bolts and nut.
Torque:
39 N
⋅
m (400 kgf
⋅
cm, 29 ft
⋅
lbf) for bolt
43 N
⋅
m (440 kgf
⋅
cm, 32 ft
⋅
lbf) for nut
16. INSTALL POWER STEERING (PS) RESERVOIR TANK
AND BRACKET
Install the reservoir tank and bracket assembly with the 3
bolts.
17. INSTALL POWER STEERING (PS) TUBES
Install the PS tube clamp with the bolt.
18. INSTALL
GENERATOR
(a) Install the generator and transmission oil cooler pipe bracket
with the bolt and nut.
Torque: 37 N
⋅
m (380 kgf
⋅
cm, 27 ft
⋅
lbf)
(b) Connect the generator connector.
(c) Connect the generator wire with the nut and cap.
19. INSTALL WIRE CLAMP (FOR GENERATOR) AND VSV
(FOR EVAP)
(a) Install the wire clamp to the VSV bracket.
(b) Install the VSV with the 2 bolts.
EG–198
–
1UZ–FE ENGINE
ENGINE MEHANICAL
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст