Lexus SC300 / Lexus SC400. Manual — part 351
V01868
–
1UZ–FE ENGINE
ENGINE MECHANICAL
EG–25
23. REINSTALL THEFT DETERRENT HORN
(a) Install the theft deterrent horn with the bolt.
(b) Connect the connector.
24. REINSTALL RH CYLINDER HEAD COVER
(a) Remove any old packing (FIPG) material.
(b) Apply seal packing to the cylinder head as shown in the
illustration.
Seal packing:
Part No. 08826–00080 or equivalent
(c) Install the gasket to the cylinder head cover.
(d) Install the seal washer to the bolt.
(e) Install the cylinder head cover with the 8 bolts.
Torque: 5.9 N
⋅
m (60 kgf
⋅
cm, 52 in.
⋅
lbf)
(f) Connect the 4 high–tension cords to the spark plugs.
(g) Connect the front high–tension cord clamp to the lower
high–tension cord cover.
(h) Place the front high–tension cord clamp to the rear
high–tension cord clamp.
(i) Install
the 2 bolts holding the high–tension cord clamps to the
cylinder head cover.
(j) Connect
the 5 high–tension cords to the front side of the front
high–tension cord clamp.
(k) Connect
the No. 2 high–tension cord to the cord clamp on the
front high–tension cord clamp.
EG–26
–
1UZ–FE ENGINE
ENGINE MECHANICAL
25. REINSTALL LH CYLINDER HEAD COVER
(a) Remove any old packing (FIPG) material.
(b) Apply seal packing to the cylinder head as shown in the
illustration.
Seal packing:
Part No. 08826–00080 or equivalent
(c) Install the gasket to the cylinder head cover.
(d) Install the seal washer to the bolt.
(e) Install the cylinder head cover with the 8 bolts.
Torque: 5.9 N
⋅
m (60 kgf
⋅
cm, 52 in.
⋅
lbf)
(f) Connect the 2 engine wire connectors.
(g) Connect the 4 injector connectors.
(h) Install the engine wire protector to the 2 brackets on the
delivery pipe.
(i)
Connect the 4 high–tension cords to the spark plugs.
(j) Connect the front high–tension cord clamp to the lower
high–tension cord cover.
(k) Place the front high–tension cord clamp to the rear
high–tension cord clamp.
(l) Install
the 2 bolts holding the high–tension cord clamps to the
cylinder head cover.
(m) Connect the 5 high–tension cords to the front side of the front
high–tension cord clamp.
–
1UZ–FE ENGINE
ENGINE MECHANICAL
EG–27
(n) Connect
the No. 1 high–tension cord to the cord clamp on the
front high–tension cord clamp.
26. REINSTALL THROTTLE BODY
(a) Disconnect the following hoses:
(1) PCV hose to throttle body
(2) Water bypass hose to throttle body
(b) Install a new gasket and throttle body with the 2 bolts and 2
nuts.
Torque: 18 N
⋅
m (185 kgf
⋅
cm, 13 ft
⋅
lbf)
(c) Install the water bypass pipe (from the rear bypass joint) to
the clamp on the engine wire cover.
(d) Connect the following hoses:
(1) Water bypass hose to IAC valve
(2) California:
Vacuum hose from throttle body
(3) Except
California:
3 vacuum hoses from throttle body
EG–28
–
1UZ–FE ENGINE
ENGINE MECHANICAL
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст