Lexus SC300 / Lexus SC400. Manual — part 517
INSPECTION OF INJECTORS
1. INSPECT
INJECTOR
INJECTION
CAUTION: Keep injector clear of sparks during the test.
(a) Remove the two bolts and fuel hose clamp.
(b) Disconnect the fuel inlet hose from the fuel tube.
(c) Connect SST (hose) to the fuel inlet tube with SST
(union). Tighten the flare nut on the fuel tube.
SST 09268–41045 (90405–52010)
Torque: 30 N
⋅
m (310 kgf
⋅
cm, 22 ft
⋅
lbf)
HINT: Use SST. (See page
)
SST 09631–22020
(d) Install a new O–ring to the fuel inlet of the pressure
regulator.
(e) Connect SST (hose) to the fuel inlet of the pressure
regulator with SST (union) and the two bolts.
SST 09268–41045 (09268–41090)
(f) Connect the fuel return hose to the fuel outlet of the
pressure regulator with SST (union), two new gaskets
and union bolt.
SST 09268–41045 (90405–09015)
FI–30
–
EFI SYSTEM
Fuel System (Injectors)
(g) Install the grommet and a new O–ring to the injector.
(h) Connect SST (hose) to the injector with SST (union),
and hold the injector and union with SST (clamp).
SST 09268–41045
(i)
Put the injector into the graduated cylinder.
HINT: Install a suitable vinyl hose onto the injector to prevent
gasoline from splashing out.
(j)
Using SST, connect terminals +B and FP of the check
(”DIAGNOSIS”) connector.
SST 09843–18020
(k) Reconnect the cable to negative (–) terminal of battery.
(l)
Turn the ignition switch ON.
NOTICE: Do not start the engine.
(m) Connect SST (wire) to the injector and battery for 15
seconds, and measure the injection volume with a
graduated cylinder. Test each injector two or three
times.
SST 09842–30070
Volume: 70–88 cm
3
(4.3–5.4 cu in.) per 15 sec.
Difference between each injector:
9 cm
3
(0.5 cu in.) or less
If the injection volume is not as specified, replace the injector.
2. INSPECT
LEAKAGE
(a) In the condition above, disconnect the test probes of
SST (wire) from the battery and check the fuel leakage
from the injector.
SST 09842–30070
Fuel drop: One drop or less per minute
(b) Disconnect the battery negative (–) cable.
(c) Remove
SST.
SST 09268–41045 and 09843–18020
(d) Reconnect the fuel inlet hose to the fuel tube.
SST 09631–22020
Torque: 30 N
⋅
m (310 kgf
⋅
cm, 22 ft
⋅
lbf)
HINT: Use a torque wrench with a fulcrum length of 30 cm
(11.81 in.).
–
EFI SYSTEM
Fuel System (Injectors)
FI–31
(e) Install the fuel hose clamp with the two bolts.
INSTALLATION OF INJECTORS
(See Components on page
)
1.
INSTALL INJECTORS AND DELIVERY PIPE
(a) Install the grommet to each injector.
(b) Apply a light coat of gasoline to a new O–ring and install
it to each injector.
(c) While turning the injector clockwise and
counterclockwise, push it to the delivery pipe. Install the
six injectors.
(d) Position the injector connector outward.
(e) Place the six insulators and three spacers in position on
the intake manifold.
(f)
Place the six injectors together with the delivery pipe in
position on the cylinder head.
FI–32
–
EFI SYSTEM
Fuel System (Injectors)
(g) Temporarily install the three bolts holding the delivery
pipe to the cylinder head.
(h) Check that the injectors rotate smoothly.
HINT: If injectors do not rotate smoothly, the probable cause
is incorrect installation of O–rings. Replace the O–rings.
(i)
Position the injector connector upward.
(j)
Tighten the three bolts holding the delivery pipes to the
intake manifold.
Torque: 21 N
⋅
m (210 kgf
⋅
cm, 15 ft
⋅
lbf)
2.
INSTALL CONTROL VALVE ACTUATOR
(a) Install the actuator with the two bolts.
Torque: 6.8 N
⋅
m (70 kgf
⋅
cm, 61 in.
⋅
lbf)
(b) Inspect the IACV. (See page
3. CONNECT
INJECTOR
CONNECTORS
HINT: The No. 1, No. 3 and No. 5 injector connectors are gray,
and the No. 2, No. 4 and No. 6 injector connectors are dark
gray.
4.
CONNECT VACUUM SENSING HOSE
–
EFI SYSTEM
Fuel System (Injectors)
FI–33
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст