Lexus SC300 / Lexus SC400. Manual — part 213
(c) Turn the defogger switch ON and check that the test bulb and
indicator light turn ON, then turn OFF after about 15 minutes.
If operation is not as specified, replace the air conditioner control
panel assembly.
(Defogger Relay)
INSPECTION OF DEFOGGER RELAY
INSPECT RELAY CONTINUITY AND OPERATION
If continuity is not as specified, replace the relay.
(Defogger Wires)
INSPECTION AND REPAIR OF
DEFOGGER WIRES
1.
INSPECT DEFOGGER WIRES
NOTICE:
•
When cleaning the glass, use a soft, dry cloth, and wipe
the glass in the direction of the wire. Take care not to
damage the wires.
•
Do not use detergents or glass cleaners with abrasive
ingredients.
•
When measuring voltage, wind a piece of tin foil around
the top of the negative probe and press the foil against
the wire with your finger as shown.
(a) Turn the ignition switch ON.
(b) Turn the defogger switch ON.
(c) Inspect the voltage at the center of each heat wire as
shown.
ÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑ
Voltage
ÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑ
Criteria
ÑÑÑÑÑÑÑÑÑÑ
Approx. 5 V
ÑÑÑÑÑÑÑÑÑÑ
Okay (No break in wire)
ÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑ
Approx. 10 V or 0 V
ÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑ
Broken wire
HINT: If there is approximately 10 volts, the wire is broken be-
tween the center of the wire and the positive (+) end. If there
is no voltage, the wire is broken between the center of the
wire and ground.
–
BODY ELECTRICAL SYSTEM
Defogger System
BE–53
(d) Place the voltmeter positive (+) lead against the defogger
positive (+) terminal.
(e) Place
the voltmeter negative (–) lead with the foil strip against
the heat wire at the positive (+) terminal end and slide it
toward the negative (–) terminal end.
(f) The point where the voltmeter deflects from zero to several
volts is the place where the heat wire is broken.
HINT: IF the heat wire is not broken, the voltmeter indicates 0 volts
at the positive (+) end of the heat wire but gradually increases to
about 12 volts as the meter probe is moved to the other end.
2.
REPAIR DEFOGGER WIRES
(a) Clean the broken wire tips with a grease, wax and
silicone remover.
(b) Place the masking tape along both sides of the wire to
be repaired.
(c) Thoroughly mix the repair agent (Dupont paste No.
4817).
(d) Using a fine tip brush, apply a small amount to the wire.
(e) After a few minutes, remove the masking tape.
(f) Allow the repair to stand at least 24 hours.
(Mirror Defogger)
REMOVAL AND INSTALLATION OF
MIRROR ASSEMBLY
(See Outside Rear View Mirror on Pub. No. RM260U2, page
BO–42
)
BE–54
–
BODY ELECTRICAL SYSTEM
Defogger System
INSPECTION OF MIRROR DEFOGGER
INSPECT MIRROR DEFOGGER
(a) Connect
the positive (+) lead from the battery to terminal 7 (4)
and the negative (–) lead to terminal 8 (5).
(b) Check that the mirror becomes warm.
HINT: It will take a short time for the mirror to become warm.
If the mirror does not become warm, replace the mirror as-
sembly.
( ): w/o Driving Position Memory
Troubleshooting
You will find the cause of trouble more easily using the table shown below. In this table, the number indicate
the order priority of the causes in trouble. Check each part in the order shown. If necessary, replace the parts.
Refer to 1992 LEXUS SC300 Repair Manual (Pub. No. RM260U2)
See page
BE–4
,
20
BE–4
,
20
BE–4
,
22
BE–172
BE–173
BE–173
BE–174
–
BODY ELECTRICAL SYSTEM
Defogger System
BE–55
(TAILLIGHT SYSTEM)
Description – Taillight System
The component parts of this system and their function are as shown in the following table.
ÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
Parts Name
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
Function
ÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
Light Control Switch
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
Grounds current from the taillight control relay via the integration relay, switching each relay
and supplying current to the appropriate bulbs accordance with the switch position.
ÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
Taillight Control Relay
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
Turned on by signals from the light control switch and supplies current to each bulb.
ÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
Integration Relay
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
Carries out ”Light Auto Turn–Off” of the headlights, fog lights and taillights and cuts off cur-
rent to the light control switch in accordance with signals from the GAUGE fuse and door
courtesy switch.
ÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
Light Failure Sensor
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
This sensor senses when a bulb in rear combination light is burnt out and lights up a warning
light.
ÑÑÑÑÑÑÑÑ
Integration Relay
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
Integration Relay
(Daytime Running
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
Refer to
ÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
(
y
g
Light Relay: CANADA)
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
PARTS LOCATION – Taillight System
–
BODY ELECTRICAL SYSTEM
Lighting System
BE–53
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст