Lexus SC300 / Lexus SC400. Manual — part 831
(i)
Install the 2 bolts.
Torque: 7.8 N
⋅
m (80 kgf
⋅
cm, 69 in.
⋅
lbf)
2.
INSTALL PARKING BRAKE SHOE
(See page
3.
INSTALL ABS SPEED SENSOR
Install the sensor to the axle carrier with the bolt.
Torque: 7.8 N
⋅
m (80 kgf
⋅
cm, 69 in.
⋅
lbf)
4.
INSTALL DRIVE SHAFT
(See page
)
5.
INSTALL BRAKE DISC AND BRAKE CALIPER
(a) Align the matchmarks and install the brake disc.
(b) Install the brake caliper with the 2 bolts.
Torque: 104 N
⋅
m (1,065 kgf
⋅
cm, 77 ft
⋅
lbf)
6.
INSTALL DRIVE SHAFT LOCK NUT
(a) Torque the nut while applying the brakes.
Torque: 289 N
⋅
m (2,950 kgf
⋅
cm, 213 ft
⋅
lbf)
(b) Install the lock cap and a new cotter pin.
SA–60
–
SUSPENSION AND AXLE
REAR AXLE HUB
7. STABILIZE
SUSPENSION
(a) Install the rear wheel and lower the vehicle.
Torque: 103 N
⋅
m (1,050 kgf
⋅
cm, 76 ft
⋅
lbf)
(b) Bounce
the vehicle up and down several times to stabilize the
suspension.
8.
TORQUE BOLT AND NUTS
(a) Jack up the vehicle and remove the rear wheel.
(b) Support the axle carrier with jack.
(c) Torque the bolt and nuts.
Torque: 184 N
⋅
m (1,880 kgf
⋅
cm, 136 ft
⋅
lbf)
9.
INSTALL REAR WHEEL AND LOWER VEHICLE
Torque: 103 N
⋅
m (1,050 kgf
⋅
cm, 76 ft
⋅
lbf)
10. CHECK REAR WHEEL ALIGNMENT
(See page
)
HUB BOLT REPLACEMENT
SA03E–04
1.
JACK UP VEHICLE AND REMOVE REAR WHEEL
2.
REMOVE REAR BRAKE CALIPER AND BRAKE DISC
(See page
)
3.
REMOVE HUB BOLT
Using SST, remove the hub bolt.
SST 09628–10011
4.
INSTALL HUB BOLT
Install washer and nut to the hub bolt, as shown in the illustra-
tion, and install the hub bolt with torquing the nut.
5.
INSTALL REAR BRAKE DISC AND BRAKE CALIPER
(See page
)
6.
INSTALL REAR WHEEL AND LOWER VEHICLE
Torque: 103 N
⋅
m (1,050 kgf
⋅
cm, 76 ft
⋅
lbf)
–
SUSPENSION AND AXLE
REAR AXLE HUB
SA–61
REAR DRIVE SHAFT
DESCRIPTION
SA0S2–03
The drive shaft has cross–groove type joints on the differential side and on the wheel side.
SA–62
–
SUSPENSION AND AXLE
REAR DRIVE SHAFT
PREPARATION
SST (SPECIAL SERVICE TOOLS)
SA06B–02
RECOMMENDED TOOLS
SA06C–02
EQUIPMENT
SA06D–01
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
Torque wrench
ÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑ
–
SUSPENSION AND AXLE
REAR DRIVE SHAFT
SA–63
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст