Lexus RC-F (2022 year). Manual in english — page 2
44
1-2. Child safety
Points to remember: P.44
When using a child restraint system:
P.45
Child restraint system compatibility for
each seating position: P.48
Child restraint system installation
method: P.53
• Fixed with a seat belt: P.53
• Fixed with an ISOFIX lower anchor-
age: P.55
• Using a top tether anchorage: P.56
Prioritize and observe the warn-
ings, as well as the laws and regula-
tions for child restraint systems.
Use a child restraint system until the
child becomes large enough to
properly wear the vehicle’s seat belt.
Choose a child restraint system
appropriate to the age and size of
the child.
Note that not all child restraint sys-
tems can fit in all vehicles.
Before using or purchasing a child
restraint system, check the compati-
bility of the child restraint system
with seat positions.
Child restraint systems
Before installing a child restraint
system in the vehicle, there are pre-
cautions that need to be observed,
different types of child restraint sys-
tems, as well as installation meth-
ods, etc., written in this manual.
Use a child restraint system when
riding with a small child that can-
not properly use a seat belt. For
the child’s safety, install the child
restraint system to a rear seat. Be
sure to follow the installation
method that is in the operation
manual enclosed with the
restraint system.
The use of a Lexus genuine child
restraint system is recom-
mended, as it is safer to use in this
vehicle. Lexus genuine child
restraint systems are made specif-
ically for Lexus vehicles. They can
be purchased at a Lexus dealer.
Table of contents
Points to remember
WARNING
■
When a child is riding
Observe the following precautions.
Failure to do so may result in death or
serious injury.
●
For effective protection in automobile
accidents and sudden stops, a child
must be properly restrained, using a
seat belt or child restraint system
which is correctly installed. For installa-
tion details, refer to the operation man-
ual enclosed with the child restraint
system. General installation instruction
is provided in this manual.
●
Lexus strongly urges the use of a
proper child restraint system that con-
forms to the weight and size of the
child, installed on the rear seat.
According to accident statistics, the
child is safer when properly restrained
in the rear seat than in the front seat.
45
1
1-2. Child safety
For safety and security
■
When installing a child restraint
system to a front passenger seat
For the safety of a child, install a child
restraint system to a rear seat. When
installing child restraint system to a
front passenger seat is unavoidable,
adjust the seat as follows and install the
child restraint system.
Move the front seat fully rearward.
Adjust the seat height to the upper
most position.
Adjust the seatback angle to the
most upright position.
When installing a forward-facing child
seat, if there is a gap between the child seat
and the seatback, adjust the seatback
angle until good contact is achieved.
WARNING
●
Holding a child in your or someone
else’s arms is not a substitute for a child
restraint system. In an accident, the
child can be crushed against the wind-
shield or between the holder and the
interior of the vehicle.
■
Handling the child restraint system
If the child restraint system is not prop-
erly fixed in place, the child or other pas-
sengers may be seriously injured or even
killed in the event of sudden braking, sud-
den swerving, or an accident.
●
If the vehicle were to receive a strong
impact from an accident, etc., it is pos-
sible that the child restraint system has
damage that is not readily visible. In
such cases, do not reuse the restraint
system.
●
Depending on the child restraint sys-
tem, installation may be difficult or
impossible. In those cases, check
whether the child restraint system is
suitable for installment in the vehicle.
(
P.48) Be sure to install and
observe the usage rules after carefully
reading the child restraint system fixing
method in this manual, as well as the
operation manual enclosed with the
child restraint system.
●
Keep the child restraint system prop-
erly secured on the seat even if it is not
in use. Do not store the child restraint
system unsecured in the passenger
compartment.
●
If it is necessary to detach the child
restraint system, remove it from the
vehicle or store it securely in the trunk.
When using a child restraint sys-
tem
WARNING
■
When installing a child restraint sys-
tem
Observe the following when installing
child restraint system to the front passen-
ger seat if it is unavoidable. The front pas-
senger SRS airbag inflates with
considerable speed and force that if not
observed may lead to death or serious
injury to the child.
46
1-2. Child safety
WARNING
●
Never use a rear-facing child restraint
system on the front passenger seat
when the airbag manual on-off switch
is on. (
P.42)
The force of the rapid inflation of the
front passenger airbag can cause
death or serious injury to children in
the event of an accident.
●
There is a label(s) on the passenger
side sun visor, indicating it is forbidden
to attach a rear-facing child restraint
system to the front passenger seat.
Details of the label(s) are shown in the
illustration below.
47
1
1-2. Child safety
For safety and security
WARNING
WARNING
●
Only put a forward-facing child
restraint system on the front seat when
unavoidable. When installing a for-
ward-facing child restraint on the front
passenger seat, move the seat as far
back as possible. Failing to do so may
result in death or serious injury if the
airbags deploy (inflate).
●
Do not allow the child to lean his/her
head or any part of his/her body
against the door or the area of the seat,
front pillars or roof side rails from
which the SRS side airbags or SRS
curtain shield airbags deploy even if
the child is seated in the child restraint
system. It is dangerous if the SRS side
and curtain shield airbags inflate, and
the impact could cause death or seri-
ous injury to the child.
●
When a junior seat is installed, always
ensure that the shoulder belt is posi-
tioned across the center of the child’s
shoulder. The belt should be kept away
from the child’s neck, but not so that it
could fall off the child’s shoulder.
●
Use child restraint system suitable to
the age and size of the child and install
it to the rear seat.
48
1-2. Child safety
■
Child restraint system compatibil-
ity for each seating position
Compatibility of each seating position
with child restraint systems (
P.49)
displays the type of child restraint sys-
tems that can be used and possible
seating positions for installation using
symbols. Also, the recommended child
restraint system that is suitable for your
child can be selected.
Otherwise, check [Recommended
child restraint systems and Compatibil-
ity table] for recommended child
restraint systems. (
P.52)
Check the selected child restraint sys-
tem together with the following
[Before confirming the compatibility of
each seating position with child
restraint systems].
■
Before confirming the compatibil-
ity of each seating position with
child restraint systems
1
Checking the child restraint system
standards.
Use a child restraint system that
conforms to UN(ECE) R44
*1
or
UN(ECE) R129
*1, 2
.
The following approval mark is dis-
played on child restraint systems
which are conformed.
Check for an approval mark
attached to the child restraint sys-
tem.
Example of the displayed regulation Num-
ber
UN(ECE) R44 approval mark
*3
The weight range of the child who is
applicable for an UN(ECE) R44
approval mark is indicated.
UN(ECE) R129 approval mark
*3
The height range of the child who is
applicable as well as available
weights for an UN(ECE) R129
WARNING
●
If the driver’s seat interferes with the
child restraint system and prevents it
from being attached correctly, attach
the child restraint system to the
right-hand rear seat (left-hand drive
vehicles) or the left-hand rear seat
(right-hand drive vehicles). (
P.52)
●
Adjust the front passenger seat so that
it does not interfere with the child
restraint system.
Child restraint system compati-
bility for each seating position
A
B
49
1
1-2. Child safety
For safety and security
approval mark is indicated.
2
Checking the category of the child
restraint system.
Check the approval mark of the
child restraint system for which of
the following categories the child
restraint system is suitable.
Also, if there are any uncertainties,
check the user’s guide included
with the child restraint system or
contact the retailer of the child
restraint system.
• “universal”
• “semi-universal”
• “restricted”
• “vehicle specific”
*1
: UN(ECE) R44 and UN(ECE) R129
are U.N. regulations for child restraint
systems.
*2
: The child restraint systems mentioned in
the table may not be available outside of
the EU area.
*3
: The displayed mark may differ depend-
ing on the product.
■
Compatibility of each seating posi-
tion with child restraint systems
Left-hand drive vehicles
Right-hand drive vehicles
*1, 2
*3
50
1-2. Child safety
*1
: Move the front seat fully rearward. If the
passenger seat height can be adjusted,
move it to the upper most position.
*2
: Adjust the seatback angle to the most
upright position. When installing a for-
ward-facing child seat, if there is a gap
between the child seat and the
seatback, adjust the seatback angle
until good contact is achieved.
*3
: Use only a front-facing child restraint
system when the airbag manual on-off
switch is on.
■
Detail information for child restraint systems installation
Suitable for “universal” category
child restraint system fixed with
the seat belt.
Suitable for child restraint systems
given on recommended child
restraint systems and compatibility
table (
P.52)
Suitable for ISOFIX child restraint
system.
Includes a top tether anchorage
point.
Never use a rear-facing child
restraint system on the front pas-
senger seat when the airbag man-
ual on-off switch is on.
Seating position
Seat position number
Airbag manual on-off
switch
ON
OFF
Seating position suitable for uni-
versal belted (Yes/No)
Yes
Forward
facing only
Yes
Yes
Yes
i-Size seating position (Yes/No)
No
No
No
No
Seating position suitable for lateral
fixture (L1/L2/No)
No
No
No
No
Suitable rearward facing fixture
(R1/R2X/R2/R3/No)
No
No
R1
*
R1
*
51
1
1-2. Child safety
For safety and security
*
: Adjust the position of the front seat as far forward as possible.
ISOFIX child restraint systems are divided into different “fixture”. The child
restraint system can be used in the seating positions for “fixture” mentioned in the
table above. For kind of “fixture” relation, confirm the following table.
If your child restraint system has no kind of “fixture” (or if you cannot find informa-
tion in the table below), please refer to the child restraint system “vehicle list” for
compatibility information or ask the retailer of your child seat.
Suitable forward facing fixture
(F2X/F2/F3/No)
No
No
F2X, F2
F2X, F2
Suitable junior seat fixture
(B2/B3/No)
No
No
No
No
Fixture
Description
F3
Full-height, forward-facing child restraint systems
F2
Reduced-height forward-facing child restraint systems
F2X
Reduced-height forward-facing child restraint systems
R3
Full-size, rearward-facing child restraint systems
R2
Reduced-size, rearward-facing child restraint systems
R2X
Reduced-size, rearward-facing child restraint systems
R1
Rearward-facing infant seat
L1
Left lateral-facing (carrycot) infant seat
L2
Right lateral-facing (carrycot) infant seat
B2
Junior seat
B3
Junior seat
Seating position
Seat position number
Airbag manual on-off
switch
ON
OFF
52
1-2. Child safety
■
Recommended child restraint systems and Compatibility table
The child restraint systems mentioned in the table may not be available outside the
EU area.
When installing a child restraint in
the rear seats, adjust the front seat
so that it does not interfere with the
child or child restraint system.
When installing a child seat with
support base, if the child seat inter-
feres with the seatback when latch-
ing it into the support base, adjust
the seatback rearward until there is
no interference.
If the seat belt shoulder anchor is
ahead of the child seat belt guide,
move the seat cushion forward.
When installing a junior seat, if the
child in your child restraint system is
in a very upright position, adjust the
seatback angle to the most comfort-
able position. And if the seat belt
shoulder anchor is ahead of the
child seat belt guide, move the seat
cushion forward.
Mass groups
Recommended Child
Restraint System
Seating position
Airbag manual
on-off switch
ON
OFF
0, 0+
Up to 13 kg (28 lb.)
G0+, BABY SAFE PLUS
(Yes/No)
No
Yes
Yes
Yes
G0+ BABY SAFE PLUS
with SEAT BELT FIXATION,
BASE PLATFORM
(Yes/No)
No
Yes
Yes
Yes
I
9 to 18 kg (20 to
39 lb.)
LEXUS DUO PLUS
(Yes/No)
Yes
Belt fix
only
Yes
Belt fix
only
Yes
Yes
53
1
1-2. Child safety
For safety and security
Confirm with the operation manual enclosed with the child restraint system about
the installation of the child restraint system.
■
Installing child restraint system
using a seat belt
Install the child restraint system in
accordance to the operation manual
enclosed with the child restraint sys-
tem.
If the child restraint system on hand is
not within the “universal” category (or
the necessary information is not in the
Child restraint system installation method
Installation method
Page
Seat belt attachment
P.53
ISOFIX lower anchorage
attachment
P.55
Top tether anchorage
attachment
P.56
Child restraint system fixed with
a seat belt
54
1-2. Child safety
table), refer to the “Vehicle List” pro-
vided by the child restraint system
maker for various possible installation
positions, or check the compatibility
after asking the retailer of the child
seat. (
P.48, 49)
1
If installing the child restraint sys-
tem to the front passenger seat is
unavoidable, refer to P.45for the
front passenger seat adjustment.
2
Run the seat belt through the child
restraint system and insert the plate
into the buckle. Make sure that the
belt is not twisted. Securely fix the
seat belt to the child restraint sys-
tem in accordance to the directions
enclosed with the child restraint
system.
3
If your child restraint system is not
equipped with a lock-off (a seat belt
locking feature), secure the child
restraint system using a locking clip.
4
After installing the child restraint
system, rock it back and forth to
ensure that it is installed securely.
(
P.55)
■
Removing a child restraint system
installed with a seat belt
Press the buckle release button and
fully retract the seat belt.
When releasing the buckle, the child
restraint system may spring up due to the
rebound of the seat cushion. Release the
buckle while holding down the child
restraint system.
Since the seat belt automatically reels itself,
slowly return it to the stowing position.
■
When installing a child restraint system
You may need a locking clip to install the
child restraint system. Follow the instruc-
tions provided by the manufacturer of the
system. If your child restraint system does
not provide a locking clip, you can purchase
the following item from any authorized
Lexus retailer or Lexus authorized repairer,
or any reliable repairer: Locking clip for
child restraint system (Part No.
73119-22010)
55
1
1-2. Child safety
For safety and security
■
ISOFIX lower anchorages
(ISOFIX child restraint system)
Lower anchorages are provided for the
each rear seats. (Mark displaying the
location of the anchorages are
attached to the seats.)
■
Installation with ISOFIX lower
anchorage (ISOFIX child restraint
system)
Install the child restraint system in
accordance to the operation manual
enclosed with the child restraint sys-
tem.
If the child restraint system on hand is
not within the “universal” category (or
the necessary information is not in the
table), refer to the “Vehicle List” pro-
vided by the child restraint system
maker for various possible installation
positions, or check the compatibility
after asking the retailer of the child
seat. (
P.48, 49)
WARNING
■
When installing a child restraint sys-
tem
Observe the following precautions.
Failure to do so may result in death or
serious injury.
●
Do not allow children to play with the
seat belt. If the seat belt becomes
twisted around a child’s neck, it may
lead to choking or other serious inju-
ries that could result in death. If this
occurs and the buckle cannot be
unfastened, scissors should be used to
cut the belt.
●
Ensure that the belt and plate are
securely locked and the seat belt is not
twisted.
●
Shake the child restraint system left
and right, and forward and backward
to ensure that it has been securely
installed.
●
After securing a child restraint system,
never adjust the seat.
●
When a junior seat is installed, always
ensure that the shoulder belt is posi-
tioned across the center of the child’s
shoulder. The belt should be kept away
from the child’s neck, but not so that it
could fall off the child’s shoulder.
●
Follow all installation instructions pro-
vided by the child restraint system
manufacturer.
Child restraint system fixed with
an ISOFIX lower anchorage
56
1-2. Child safety
1
Check the positions of the exclu-
sive fixing bars, and install the child
restraint system to the seat.
2
After installing the child restraint
system, rock it back and forth to
ensure that it is installed securely.
(
P.55)
■
Top tether anchorages
Top tether anchorages are provided
for the each rear seat.
Use top tether anchorages when fixing
the top strap.
Top tether anchorages
Top strap
■
Fixing the top strap to the top
tether anchorages
Install the child restraint system in
accordance to the operation manual
enclosed with the child restraint sys-
tem.
Open the anchor bracket cover, latch
the hook onto the anchor bracket and
tighten the top strap.
Make sure the top strap is securely latched.
(
P.55)
WARNING
■
When installing a child restraint sys-
tem
Observe the following precautions.
Failure to do so may result in death or
serious injury.
●
After securing a child restraint system,
never adjust the seat.
●
When using the lower anchorages, be
sure that there are no foreign objects
around the anchorages and that the
seat belt is not caught behind the child
restraint system.
●
Follow all installation instructions pro-
vided by the child restraint system
manufacturer.
Using a top tether anchorage
A
B
57
1
1-2. Child safety
For safety and security
Top strap
Hook
WARNING
■
When installing a child restraint sys-
tem
Observe the following precautions.
Failure to do so may result in death or
serious injury.
●
Firmly attach the top strap and make
sure that the belt is not twisted.
●
Do not attach the top strap to anything
other than the top tether anchorage.
●
After securing a child restraint system,
never adjust the seat.
●
Follow all installation instructions pro-
vided by the child restraint system
manufacturer.
NOTICE
■
Top tether anchorages
When not in use, make certain to close
the lid. If it remains open, the lid may be
damaged.
A
B
58
1-3. Theft deterrent system
1-3.Theft deterrent system
The indicator light flashes after the
engine switch has been turned off to
indicate that the system is operating.
The indicator light stops flashing after
the engine switch has been turned to
ACCESSORY or IGNITION ON
mode to indicate that the system has
been canceled.
■
System maintenance
The vehicle has a maintenance-free type
engine immobilizer system.
■
Conditions that may cause the system to
malfunction
●
If the grip portion of the key is in contact
with a metallic object
●
If the key is in close proximity to or touch-
ing a key registered to the security sys-
tem (key with a built-in transponder chip)
of another vehicle
Engine immobilizer system
The vehicle’s keys have built-in
transponder chips that prevent the
engine from starting if a key has not
been previously registered in the
vehicle’s on-board computer.
Never leave the keys inside the
vehicle when you leave the vehicle.
This system is designed to help pre-
vent vehicle theft but does not
guarantee absolute security
against all vehicle thefts.
Operating the system
NOTICE
■
To ensure the system operates cor-
rectly
Do not modify or remove the system. If
modified or removed, the proper opera-
tion of the system cannot be guaranteed.
59
1
1-3. Theft deterrent system
For safety and security
■
Setting
Turn the engine switch off, have all the
passengers exit the vehicle and ensure
that both side doors are closed.
Using the entry function: Touch the
sensor area on the outside door handle
twice within 5 seconds.
Using the wireless remote control:
Press
twice within 5 seconds.
■
Canceling
Using the entry function: Hold the out-
side door handle.
Using the wireless remote control:
Press .
Double locking system
Unauthorized access to the vehicle
is prevented by disabling the door
unlocking function from both the
interior and exterior of the vehicle.
Vehicles employing this system
have labels on the side windows.
Setting/canceling the double
locking system
WARNING
■
Double locking system precaution
Never activate the double locking sys-
tem when there are people in the vehicle
because both side doors cannot be
opened from inside the vehicle.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст