Mercedes-Benz ML320. Manual — part 794
AR91.18-P-1850GI
Remove and install cover on rear seat cushion
6.5.99
MODELS 163.136 /154 /172 as of 1.9.99,
163.113 /128 /157 /174 /175
P91.18-2031-09
1
Paneling of horizontal adjustment
handle
2
Horizontal adjustment handle
3
Rear seat cushion frame
8
Rear seat cushion
4
Lower cover
5
Rear seat upholstery side lip
6
Velcro closure
7
Rear seat cover
Remove/Install
1
Remove rear cargo space floor flaps
See Operating Instructions
2
Remove outer cover from rear seat
Do not remove remaining covers.
AR91.12-P-1100GH
3
Detach lateral curtain at bottom
4
Remove paneling of horizontal adjustment
handle (1)
Risk of breakage!
Unscrew screw and press paneling of
horizontal adjustment handle forwards in
order to unhook the retaining lugs.
5
Remove side cover on rear backrest fitting
6.1
Remove lower cover (4)
Only with 3rd seat row, code 847.
7
Detach rear seat cover (7) and Velcro closure
(6) at the outside of the rear seat cushion
frame (3)
8.1
Turn ignition key to "0" position
Only with side airbag in left and right rear,
code 293. To avoid fault codes.
9.1
Disconnect connector of electrical line of rear
side seat belt buckle and move out of
retaining clip
Only with side airbag in the rear
(left and right), code 293.
10.1
Carefully lift up rear seat cover and unscrew
bolt from belt end fitting
Do not damage rear seat cover.
Only 60% rear seat.
*BA91.40-P-1001-01D
Torx bit set
*000589011000
11.1
Remove belt end fitting together with rear
seat seat belt buckle though the rear seat
cushion
Do not damage rear seat cover.
Only 60% rear seat.
12
Remove rear seat cushion (8) from rear seat
cushion frame (3)
13
Pull off rear seat upholstery (7) until the
stapled wire rings become visible
14
Bend stapled wire rings up
Copyright DaimlerChrysler AG 14.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorded by Modification services.
Page 1
15
Detach the staple wires from the opened wire
rings at rear seat cover (7)
16
Remove rear seat cover (7) from rear seat
upholstery (8)
17
Install in the reverse order
Seat belts/emergency tensioning retractors
Number
Designation
Model
163 as of
09/99
BA91.40-P-1001-01D
Screw on belt end fitting
Nm
35
Torx bit set
000 589 01 10 00
Copyright DaimlerChrysler AG 14.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorded by Modification services.
Page 2
AR91.12-P-1110GH
Remove and install rear seat cushion frame
23.5.00
MODELS 163.136 /154 /172 as of 1.9.99,
163.113 /128 /157 /174 /175
P91.12-2205-01
P91.12-2206-01
P91.12-2257-01
P91.12-2258-01
P91.12-2259-01
1
Retaining strap bolt
2
Rear seat cushion frame mounting
screws
3
Rear seat cushion frame
4
Screw
10
Clip
11
Cover
12
Rubber grommet
13
Handle locking device
5
Vertical adjustment handle
6
Vertical adjustment cable
7
Clip
8
Horizontal adjustment cable
9
Clip
Remove/install
1.1
Loosen Velcro lock in the left rear corner of
the rear seat cushion frame
Only 60% rear seat
2.1
Unscrew screw of retaining strap (1)
Only 60% rear seat
*BA91.12-P-1009-03A
Torx bit set
*000589011000
3
Remove paneling of horizontal adjustment
handle
Risk of breakage!
Unscrew screw and press paneling of
horizontal adjustment handle forwards in
order to unhook the retaining lugs.
4
Remove outer cover from rear seat
Do not remove the remaining covers.
AR91.12-P-1100GH
5
Remove curtain from the front and side of the
rear seat
6
Remove fold-down rear backrest
AR91.12-P-1720GI
7
Unhook the front of the rear seat covering on
both sides and at the back of the rear seat
cushion frame
8
Remove rear seat covering and rear seat
cushion from the rear seat cushion frame
Installation: if a new rear seat cushion
frame is used for the 60% rear seat, the
center Velcro closure must be glued on.
9.1
Remove locking mechanism for automatic
front seat adjustment for easy entry to the rear
Only 40% rear seat for the 3rd seat row,
code 847.
AR91.12-P-1120GH
10
Detach cover (11) from vertical adjustment
handle (5)
11
Unscrew bolt (4) and detach vertical
adjustment handle (5) from rear seat cushion
frame
Press unlocking device and pull vertical
adjustment handle forwards. Observe
installed position of spring!
12
Unhook vertical adjustment cable (6) from
clips (7, 9)
Risk of breakage!
Clip (7) is concealed behind adhesive tape.
Installation: glue on adhesive tape again
Copyright DaimlerChrysler AG 14.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorded by Modification services.
Page 1
13
Unhook vertical adjustment cable (6) from
vertical adjustment handle (5)
14
Guide vertical adjustment cable (6) through
grommet (12)
Installation: If a new rear seat cushion
frame is used, the grommet must be installed
in the new rear seat cushion frame.
15
Remove handle locking device (13) from rear
seat cushion frame
16
Unhook horizontal adjustment cable (8) at clip
(10) and at front of rear seat cushion frame
Risk of breakage!
17
Unscrew bolts from horizontal adjustment
handle
18
Detach horizontal adjustment cable (8) from
horizontal adjustment handle
Risk of breakage!
Pull out horizontal adjustment handle.
19
Remove rear seat seat belt buckle
40% rear seat without side airbag in left
and right rear, code 293.
AR91.40-P-1516GH
40% rear seat with side airbag in left and
right rear, code 293.
AR91.40-P-1516GK
60% rear seat outer seat.
AR91.40-P-1516GJ
20
Unscrew mounting screws for rear seat
cushion frame (2)
Installation: Replace damaged shims at
the diagonal supports of the rear seat.
*BA91.12-P-1010-03A
21
Remove rear seat cushion frame (3)
Remove rear seat cushion frame through
tailgate
22
Install in the reverse order
Rear seats
Number
Designation
Model
163 as of
09/99
BA91.12-P-1009-03A
Bolt for clamping band to seat frame
Nm
45
BA91.12-P-1010-03A
Screw for bracket to seat frame
Nm
23
Torx bit set
000 589 01 10 00
Copyright DaimlerChrysler AG 14.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorded by Modification services.
Page 2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст