Mercedes-Benz ML320. Manual — part 770
AR94.30-P-5400GH
Remove/install noise encapsulation
16.8.01
MODEL
163.113 /128
P94.30-2011-12
1
Noise encapsulation, front section
2
Headless setscrew
3
Plastic clip
4
Noise encapsulation, center section
5
Noise encapsulation, rear section
Remove, install
Installation
Inspect headless setscrews and plastic clips,
replace if necessary.
1
Remove headless setscrews (2) and plastic
clips (3) from noise encapsulation front
section (4)
6 headless setscrews and plastic clips.
2
Remove noise encapsulation front section (1)
3
Remove headless setscrews (2) and plastic
clips (3) from noise encapsulation center
section (4)
4 headless setscrews and plastic clips.
4
Remove (4) noise encapsulation center section
5
Remove headless setscrews (2) and plastic
clips (3) from noise encapsulation rear section
(5)
8 headless setscrews and plastic clips.
6
Remove noise encapsulation rear section (5)
7
Install in reverse order
Copyright DaimlerChrysler AG 12.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorded by Modification services.
Page 1
AR94.30-P-5500GH
Modify noise encapsulation
12.9.01
MODEL
163.113
P94.30-2012-11
1
Noise encapsulation, front section
2
Insulation cubes
3
Scribe line, horizontal
4
Scribe line, vertical
5
Area to be removed
r
10 mm
Remove
1
Remove noise encapsulation front section (1)
Do NOT remove other encapsulation
sections.
AR94.30-P-5400GH
Modify
2
Flatten insulation cubes (2)
3
Scribe two 38 mm vertical lines (4) forward
from rear edge of encapsulation
Vertical scribe lines should be flush with
outside edges of rear cutout in encapsulation.
4
Scribe a straight, horizontal line (3) between
vertical lines
5
Radius forward corners of scribe lines to 10
mm (r)
6
Remove area (5) of encapsulation bordered
by scribe lines
Install
7
Reinstall noise encapslation front section (1)
AR94.30-P-5400GH
Copyright DaimlerChrysler AG 17.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorded by Modification services.
Page 1
AR94.30-P-5400GH
Remove/install noise encapsulation
16.8.01
MODEL
163.113 /128
P94.30-2011-12
1
Noise encapsulation, front section
2
Headless setscrew
3
Plastic clip
4
Noise encapsulation, center section
5
Noise encapsulation, rear section
Remove, install
Installation
Inspect headless setscrews and plastic clips,
replace if necessary.
1
Remove headless setscrews (2) and plastic
clips (3) from noise encapsulation front
section (4)
6 headless setscrews and plastic clips.
2
Remove noise encapsulation front section (1)
3
Remove headless setscrews (2) and plastic
clips (3) from noise encapsulation center
section (4)
4 headless setscrews and plastic clips.
4
Remove (4) noise encapsulation center section
5
Remove headless setscrews (2) and plastic
clips (3) from noise encapsulation rear section
(5)
8 headless setscrews and plastic clips.
6
Remove noise encapsulation rear section (5)
7
Install in reverse order
Copyright DaimlerChrysler AG 17.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorded by Modification services.
Page 1
AH00.00-N-0001-01A
Notes on self-locking nuts and bolts
All models
Important repair information
Bolts with locking splines, micro-encapsulated bolts and self-
locking nuts must always be replaced after being used once.
There is an increased risk of injury when unscrewing micro-
encapsulated bolts due to the sudden breakaway torque.
Before new micro-encapsulated bolts are screwed in, the mating
thread must be re-cut in order to remove all the residue of the old bolt
locking compound.
Copyright DaimlerChrysler AG 06.07.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorded by Modification services.
Page 1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст