Mercedes-Benz ML320. Manual — part 317
8. Separate green lead (gn) from CAN bus adapter connector (8).
9. Tie TrafficStar (4) wiring harness on at height of shift gate and pull out green lead (gn).
Fig. 329: Identifying CAN Bus Adapter Connector And Trafficstar Wiring Harness
10. Route green lead (gn) to back-up lamp switch (S16/2).
11. Connect lower gray lead (gr) from connector with assignment 2 for back-up lamp switch (S16/2) to green
lead (gn) using solder connector.
The connector for the back-up lamp switch (S16/2) has two gray leads, the lower of the two leads is
for the switched back-up lamp signal.
Fig. 330: Identifying Back-Up Lamp Switch And Green Lead
12. Connect connector (8) and lead (6) to CAN bus adapter (5).
13. Install center console.
2001 Mercedes-Benz ML320
1998-2005 ACCESSORIES & BODY, CAB Electrical System - Body - 163 Chassis
me
Fig. 331: Identifying CAN Bus Adapter And Lead
14. Connect brown and black wire (br, sw) from GPS antenna lead (3) with brown and black lead (br, sw)
from TrafficStar wiring harness (4) and slide flat plug insulations together.
15. Attach flat plug connectors and GPS antenna lead (3) to TrafficStar wiring harness (4) with felt.
Fig. 332: Identifying GPS Antenna Connector And GPS Antenna Lead
16. Install counter plug (7) from TrafficStar wiring harness (4) to radio connector (A2) and wrap with felt (c).
Fig. 333: Identifying Radio Connector And Counter Plug
17. Connect radio connector (A) and GPS antenna connector (C3) with TrafficStar radio and navigation
system (1).
18. Connect radio antenna.
2001 Mercedes-Benz ML320
1998-2005 ACCESSORIES & BODY, CAB Electrical System - Body - 163 Chassis
me
19. Install TrafficStar (1) radio and navigation system.
Fig. 334: Identifying GPS Antenna Connector And Sound Connector
CARRYING OUT START-UP AND FUNCTION CHECK - AZ82.61-P-0001-04A
Models 129, 140, 163, 168, 170, 202, 208, 210
System description
Fig. 335: Identifying Trafficstar Display Field, Automatic Button And Mode Button
Step 5 for initial start-up only applies for equipment which has already been installed in a vehicle and on
which initial calibration has been performed.
Start-up step
Entry with TrafficStar
keys
Feedback on TrafficStar
display field
1
Start engine
2
Switch on TrafficStar
Enter code (see CODE
card) with
multifunction buttons
below the numbers on
the display field.
CODE 1 2 3 4 5 6 7 8
3
Insert navigation CD
into TrafficStar
Loading time approx. 1
min.
2001 Mercedes-Benz ML320
1998-2005 ACCESSORIES & BODY, CAB Electrical System - Body - 163 Chassis
me
4
Activate service mode
Press mode button (M)
repeatedly until
NAVIGATE appears
NAVIGATE
Press automatic button
(A) repeatedly until
CONFIG appears
CONFIG 1 2 3 4 5 6 7 8*
Confirm CONFIG with
multifunction button
below (*)
SYSTEM 1 2 3 4 5 6 7 8*
Confirm SYSTEM
with multifunction
button (GHI) and
(MNO)
MODULE *
5
Erase initial calibration
Applies only when
initial calibration has
been performed on the
unit
Press automatic button
(A) repeatedly until
NEW CAL appears
NEW CAL *
Confirm NEW CAL
with multifunction
button below (*)
CAUTION CALIBRATION
WILL BE ERASED
Hold multifunction
button below (*)
depressed until the
following message
appears
Initial calibration is
then erased and the
unit can be
recalibrated.
CALIBRATION ERASED
Press multifunction
button (<--)
NEW CAL *
Press automatic button
(A) repeatedly until
MODUL T appears
MODULE T *
6
Perform module test
Confirm MODUL T
with multifunction
button below (*) Press
multifunction button (<-
-)
MODULE OK
MODULE T *
7
Perform voice test
Press automatic button
(A) repeatedly until
VOICE T appears
VOICE T *
Confirm VOICE T
Voice output
2001 Mercedes-Benz ML320
1998-2005 ACCESSORIES & BODY, CAB Electrical System - Body - 163 Chassis
me
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст