Mercedes-Benz Sprinter / Dodge Sprinter. Manual — part 6
TEST
ACTION
APPLICABILITY
6
Measure the resistance of the Airbag Warning Lamp Driver circuit between the
Airbag Control Module Adaptor and ground.
Is the resistance below 5.0 ohms?
All
Yes
→ Repair the Airbag Warning Indicator Driver circuit shorted to
ground.
Perform AIRBAG VERIFICATION TEST - VER 1.
No
→ Go To 7
7
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN IGNITION
OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BEFORE
PROCEEDING.
WARNING: IF THE AIRBAG CONTROL MODULE IS DROPPED AT ANY
TIME, IT MUST BE REPLACED. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND PERSONAL INJURY OR DEATH.
If there are no possible causes remaining, view repair.
All
Repair:
Replace the Airbag Control Module in accordance with the Service
Information.
Perform AIRBAG VERIFICATION TEST - VER 1.
8
With the DRBIII
t, record and erase all DTC’s from all Airbag modules.
If equipped with Passenger Airbag On - Off switch, read the DTC’s in all switch
positions.
If any ACTIVE codes are present they must be resolved before diagnosing any stored
codes.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Look for chaffed, pierced, pinched, or partially broken wires and broken, bent, pushed
out, spread, corroded, or contaminated terminals.
The following additional checks may assist you in identifying a possible intermittent
problem.
Reconnect any disconnected components and harness connector.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION ON, THEN RECONNECT THE BATTERY.
With the DRBIII
t monitor active codes as you work through the following steps.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, MAINTAIN A SAFE
DISTANCE FROM ALL AIRBAGS WHILE PERFORMING THE FOLLOWING
STEPS.
Wiggle the wiring harness and connectors of the related airbag circuit or component.
If codes are related to the Driver circuits, rotate the steering wheel from stop to stop.
You have just attempted to simulate the condition that initially set the trouble code
message.
Did the DTC become active?
All
Yes
→ Select appropriate symptom from Symptom List.
No
→ No problem found at this time. Erase all codes before returning
vehicle to customer.
21
AIRBAG
AIRBAG WARNING INDICATOR - DRIVER LOW —
Continued
Symptom List:
DRIVER SEAT BELT TENSIONER - INCORRECT FEEDBACK
DRIVER SQUIB 1 - INCORRECT FEEDBACK
INTERNAL 1
INTERNAL 2
INTERNAL 3
PASSENGER SEAT BELT TENSIONER - INCORRECT FEEDBACK
PASSENGER SQUIB 1 - INCORRECT FEEDBACK
STORED ENERGY FIRING 1
STORED ENERGY FIRING 2
Test Note:
All symptoms listed above are diagnosed using the same tests.
The title for the tests will be DRIVER SEAT BELT TEN-
SIONER - INCORRECT FEEDBACK.
When Monitored and Set Condition:
INTERNAL 1
When Monitored:
With the ignition on, the module on board diagnostics continuously
performs internal circuit tests.
Set Condition:
This DTC will set if the module identifies an out of range internal circuit.
INTERNAL 2
When Monitored:
With the ignition on, the module on board diagnostics continuously
performs internal circuit tests.
Set Condition:
This DTC will set if the module identifies an out of range internal circuit.
INTERNAL 3
When Monitored:
With the ignition on, the module on board diagnostics continuously
performs internal circuit tests.
Set Condition:
This DTC will set if the module identifies an out of range internal circuit.
STORED ENERGY FIRING 1
When Monitored:
With the ignition on, the module on board diagnostics continuously
performs internal circuit voltage tests.
Set Condition:
This DTC will set if the ACM identifies an internal high voltages
condition.
22
AIRBAG
STORED ENERGY FIRING 2
When Monitored:
With the ignition on, the module on board diagnostics continuously
performs internal voltage tests.
Set Condition:
This DTC will set if the ACM identifies an internal low voltages condition.
POSSIBLE CAUSES
AIRBAG CONTROL MODULE - ACM
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
NOTE: Ensure the battery is fully charged.
NOTE: For the purpose of this test, the AECM and ORC modules will be
referred to as an ACM.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, IF THE MODULE IS
DROPPED AT ANY TIME, IT MUST BE REPLACED.
Select the appropriate module and DTC type combination:
All
ACM - ACTIVE DTC
Replace the Airbag Control Module in accordance with Service
Instructions.
Perform AIRBAG VERIFICATION TEST - VER 1.
ACM - STORED DTC
Replace the Airbag Control Module in accordance with Service
Instructions.
Perform AIRBAG VERIFICATION TEST - VER 1.
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
23
AIRBAG
DRIVER SEAT BELT TENSIONER - INCORRECT FEEDBACK —
Continued
Symptom:
DRIVER SEAT BELT TENSIONER CIRCUIT OPEN
When Monitored and Set Condition:
DRIVER SEAT BELT TENSIONER CIRCUIT OPEN
When Monitored:
With the ignition on the ACM monitors the resistance of the Driver
Seat Belt Tensioner circuits.
Set Condition:
The ACM has detected an open circuit or high resistance on the Driver
Seat Belt Tensioner circuits.
POSSIBLE CAUSES
DRIVER SEAT BELT TENSIONER CIRCUITS OPEN
DRIVER SEAT BELT TENSIONER LINE 1 OR LINE 2 CIRCUIT OPEN
ACM, DRIVER SEAT BELT TENSIONER CIRCUIT OPEN
STORED CODE OR INTERMITTENT CONDITION
ACTIVE CODE PRESENT
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
NOTE: Ensure the battery is fully charged.
NOTE: For the purpose of this test, the AECM and ORC modules will be
referred to as an ACM.
SELECT ACTIVE or STORED DTC:
All
ACM - ACTIVE DTC
ACM - STORED DTC
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
2
NOTE: Ensure the battery is fully charged.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN IGNITION
OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BEFORE
PROCEEDING.
Disconnect the Driver Seat Belt Tensioner connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool to the Driver Seat Belt Tensioner connector.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN IGNITION
ON, THEN RECONNECT THE BATTERY.
With the DRBIII
t, read active Airbag Control Module DTC’s.
Does the DRBIII
t display DRIVER SBT CIRCUIT OPEN?
All
Yes
→ Go To 3
No
→ Replace Driver Seat Belt Tensioner in accordance with the Service
Information.
Perform AIRBAG VERIFICATION TEST - VER 1.
24
AIRBAG
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст