Great Wall Hover. Manual — part 4
Fuel supply system
N
m: specified torque
adjustment nut
throttle pull wire
accelerator pedal assembly
carbon tank exhaust rubber tube
snap fitting
steel strip type elastic hoop
generator oil-in rubber tube
generator of return rubber tube
soft tube fixing clipper
carbon
tank
carbon tank
air inlet
rubber tube
b type
worm drive
type hoop
vaporizer tube 2
back part of fuel tank
oil-out tube
back part of fuel tank
oil return tube
fuel filter
filter rubber tube
for gas out
hard tube bracket
vaporizer soft tube 2
cleaner bracket
filter rubber
tube for gas-in
fuel tank vaporizer
rubber tube
front part of the oil-out
tube of fuel tank
vaporizer soft
tube1
vaporizer tube1
fuel tank gland
the middle connection rubber
tube of the oil return tube
front taps of fuel tank
fuel pump
fuel tank gland
fuel tank protection plate
seal packing
ring
fuel tank assembly
fuel tank oil return tube
fuel tank lock
r e f i l l o p e n i n g c u s h i o n
pressing board
refill opening cushion
oil filing port assembly
steel strip type elastic hoop
fuel tank protection plate
Caution: When maintaining the fuel supply system, if the oil
path needs to be removed, the pressure of the fuel system must
be released to avoid the ejection of high pressure fuel.
Disassembly of the fuel tank
1. First remove the oil-in and oil return hard tube of the
generator, the oil return hard tube of fuel tank, and the
connection rubber tube between the back parts of hard vaporizer
tube. Release the pressure of oil path system slowly, block the
joints with cotton cloth, lest there is ejection of high pressure
oil.
2. Remove the oil filling port at the back of the fuel tank and the
clip of the connection rubber tube of ventilation tube, there are
two clips altogether.
3.
Remove the bolts fixing the fuel tank, there are 6 bolts
altogether;
4. Remove the oil-in and oil-out tube from the fuel tank, remove
the vaporizer tube joints and line bundle connector;
The disassembly and installation of the fuel pump
Removal of components of fuel supply system
Gasoline filter disassembly
1. Firstly, use the straight screwdriver to remove the hose clamp
and remove the connecting rubber hose on both sides of gasoline
filter;
2. Loose the bolt on the gasoline filter bracket, then
remove the gasoline filter for complete replacement.
Removal of carbon tank
The disassembly of the fuel filler pipe
Removal of fuel pipe
1. Remove the connection between the in/return fuel connector of
engine fuel track and the fuel supply pipe:
a. Remove the elastic hoop firstly;
b. Remove the package connector; press down the button of package
connector by hand, then pull it out outwardly.
c. Remove the three-line plastic clip.
2. Removal of front section of fuel hard pipe
b. Pull out the fuel pipe form the clip fixing base, then remove the
hard pipe;
c. Remove the fixing base on the longitudinal beam if necessary
rotate the fixing base for 90 degree in clockwise or anticlockwise,
the take out it.
3. Removal of rear section of fuel hard pipe
a. Remove the connecting elastic hoop of two ends of rear section
of fuel hard pipe;
b. Pull out the fuel pipe form the clip fixing base, then remove the
hard pipe ;
Removal and adjustment of throttle control system
1. Removal of accelerator pedal
Remove the two fixed bolts which fix the pedal ;
2. Removal of throttle pull-wire
a. Firstly, disconnect the connection on motor, then loose the fixed
bolt ;
b. Remove the plastic clip of throttle pull-wire on pedal, remove the
end of throttle pull-wire;
c. Use the pliers to clamp the clip on the side of engine compartment
to remove the fixing base of pull-wire on the fa ade of engine
compartment.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст