Great Wall service chassis and body Manual — part 34
SA-32
(h)
Bend one tooth of the lock plate inside and other teeth
outside to lock the steering knuckle nut.
5.
Mount on the liner and the steering knuckle outer flange
cap.
Fastening torque
(23-29)Nm
6.
Mount the brake caliper
(a)
Mount the brake caliper on the steering knuckle and
screw up the bolts according to the specified torque.
Fastening torque
123Nm
(b)
Connect the Bundy tube.
Fastening torque
(20-22)Nm
7.
Check the height of the brake liquid level and add the
brake liquid as requirement, exhaust the gas in the
braking system.
Steering knuckle
Dismantle of Steering Knuckle
1.
Tear down the brake caliper, front wheel and the front
brake disc.
2.
Tear down the dust cover, and the brake shell.
3.
Tear down the steering knuckle arm from the steering
knuckle.
Suspension System and Automobile Axle (SF/2WD)
Front Wheel Hub and Steering Knuckle (Steering Knuckle)
SA-33
4.
Tear down the vibration damper from the lower arm.
5.
Tear down the transverse stabilizer rod from the lower
arm.
6.
Tear down the steering knuckle;
(a)
Tear down the split pin and groove nut of upper ball stud.
(b)
Take apart the steering knuckle from the upper ball stud
with special service tool.
(c)
Tear down the split pin and groove of the lower ball stud.
(d)
Take apart the steering knuckle from the lower ball stud
with special service tool.
(e)
Press down the lower arm to tear down the steering
knuckle.
Suspension System and Automobile Vehicle (SF/2WD)
Front Wheel Hub and Steering Knuckle (Steering Knuckle)
SA-34
7.
Tear down the lower ball stud assembly from the steering
knuckle.
Inspection on and Change of Steering
Knuckle
1.
Check the steering knuckle.
Check the steering knuckle with the dye penetration agent to
see whether there is crack or not.
If crack is found, the steering knuckle is required to be changed.
Mount of Steering Knuckle
1.
Mount the lower ball stud on the steering knuckle.
Connect the lower ball stud and steering knuckle with bolts,
which are tightened according to the specified torque.
Fastening torque
(70-90)Nm
2.
Mount on the steering knuckle
(a)
Press down the lower arm to mount on the steering
knuckle.
(b)
Mount on the lower ball stud, groove nut and screw up the
nuts according to the specified torque and then mount on
the split pin.
Fastening torque
(132-152)Nm
Suspension System and Automobile Axle (SF/2WD)
Front Wheel Hub and Steering Knuckle (Steering Knuckle)
SA-35
(c)
Mount on the upper ball stud and the groove nut that are
screwed up according to the specified torque, and then
split pin.
Fastening torque
(132-152)Nm
3.
Mount the stabilizer rod on the lower arm.
Fastening torque
(20-26)Nm
4.
Mount the vibration damper on the lower arm.
Fastening torque
(127-147)Nm
5.
Mount the steering knuckle arm and the brake oil pipe
bracket on the steering knuckle.
Coat the sealing agent 1271 on the bolt thread.
Fastening torque
180Nm
6.
Mount the dust cover and brake shell, and align the
locating hole of the dust cover with the groove of the
steering knuckle to ensure that the dust cover is concen-
tric with the steering knuckle.
Fastening torque
(25-29)Nm
7.
Mount the front wheel hub and the front brake disc as well
as the brake caliper.
8.
Check the height of brake liquid level and add the brake
liquid as requirement, then exhaust the gas in the brak-
ing system.
Suspension System and Automobile Axle (SF/2WD)
Front Wheel Hub and Steering Knuckle (Steering Knuckle)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст