Mazda 6. Manual — part 125
F–36
EXHAUST SYSTEM
.
A6E3914W002
EXHAUST SYSTEM
F–37
F
HO2S Removal Note
1. Remove the HO2S using the SST before
removing the exhaust manifold.
Exhaust Manifold Installation Note
1. Tighten the exhaust manifold installation nuts in
the order shown.
End Of Sie
1
Main silencer
2
Middle pipe
3
TWC
4
Exhaust manifold insulator (upper)
5
Bracket
6
F–37 Exhaust Manifold Installation Note
)
7
Exhaust manifold gasket
8
Exhaust manifold insulator (lower)
9
HO2S (front)
(See
10
HO2S (rear)
(See
A6J3914W004
A6E3914W003
F–38
EMISSION SYSTEM
CHARCOAL CANISTER INSPECTION
A6E391613970W01
1. Remove the charcoal canister.
2. Plug the atmosphere side port and purge solenoid valve side port of the charcoal canister.
3. Blow air into the charcoal canister from the fuel tank side port and verify that there is no air leakage.
• If there is air leakage, replace the charcoal canister.
End Of Sie
EVAPORATIVE GAS CHECK VALVE (ONE-WAY) INSPECTION (L.H.D.)
A6E391613988W01
1. Remove the evaporative gas check valve (one-way).
2. Apply pressure to port A, and verify that there is no airflow.
• If there is airflow, replace the evaporative gas check valve (one-way).
3. Apply negative pressure to port A, and verify that there is air flow.
• If there is no airflow, replace the evaporative gas check valve (one-way).
End Of Sie
PURGE SOLENOID VALVE REMOVAL/INSTALLATION
A6E391618740W01
1. Disconnect the negative battery cable.
2. Remove in the order indicated in the table.
3. Install in the reverse order of removal.
Vacuum Hose Installation Note
1. Attach the vacuum hose onto the purge solenoid valve until it contacts the stopper.
Evaporative Hose Installation Note
1. Attach the evaporative hose onto the purge solenoid valve until it contacts the stopper.
End Of Sie
EMISSION SYSTEM
A6E3916W002
A6E3916W001
1
Evaporative hose (to charcoal canister)
(See
F–38 Evaporative Hose Installation Note
2
Vacuum hose (to intake manifold)
(See
F–38 Vacuum Hose Installation Note
3
Purge solenoid valve
A6E3916W024
EMISSION SYSTEM
F–39
F
PURGE SOLENOID VALVE INSPECTION
A6E391618740W02
Airflow Inspection
Note
• Perform the following test only when directed.
1. Disconnect the negative battery cable.
2. Remove the purge solenoid valve. (See
F–38 PURGE SOLENOID VALVE REMOVAL/INSTALLATION
3. Inspect airflow between the ports under the following conditions.
• If not as specified, replace the purge solenoid valve.
• If as specified, carry out the “Circuit Open/Short Inspection”.
Circuit Open/Short Inspection
1. Disconnect the PCM connector. (See
.)
2. Inspect the following wiring harness for open or
short (continuity check).
Open circuit
• If there is no continuity, the circuit is open.
Repair or replace the harness.
— Purge solenoid valve terminal A
(harness-side) and PCM terminal 4U
— Purge solenoid valve terminal B
(harness-side) and main relay terminal C
(harness-side)
Short circuit
• If there is continuity, the circuit is shorted.
Repair or replace the harness.
— Purge solenoid valve terminal A
(harness-side) and body GND
— Purge solenoid valve terminal B (harness-side) and power supply
End Of Sie
EGR VALVE REMOVAL/INSTALLATION
A6E391620300W01
1. Disconnect the negative battery cable.
2. Disconnect the EGR valve connector.
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
Water Hose Removal Note
• Drain the engine coolant. (See
EGR Valve Removal Note
)
2. Remove the upper radiator hose. (See
E–6 RADIATOR REMOVAL/INSTALLATION
.)
End Of Sie
A6E3916W004
A6E3916W005
A6E3916W006
1
)
2
)
A6E3916W008
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст