Mazda 6. Manual — part 272
FRONT SUSPENSION
R–23
R
STABILIZER CONTROL LINK INSPECTION
A6E741434150W01
1. Remove the stabilizer control link from the vehicle.
2. Inspect for bending and damage.
3. Measure the ball joint starting torque.
(1) Rock the ball joint stud side to side 10 times.
(2) Rotate the ball joint stud 10 times.
(3) Measure the starting torque using a suitable
allen socket and a torque wrench.
Starting torque
0.23—0.47 N·m
{2.4—4.7 kgf·cm, 2.1—4.1 in·lbf}
End Of Sie
FRONT CROSSMEMBER REMOVAL/INSTALLATION
A6E741434800W01
1. Remove the under cover.
2. Remove the splash shield.
3. Remove the front auto leveling sensor.
(See
T–32 FRONT AUTO LEVELING SENSOR REMOVAL/INSTALLATION
.)
4. Remove the transverse member.
(See
R–27 TRANSVERSE MEMBER REMOVAL/INSTALLATION
.)
5. Remove the steering gear and linkage, and pipe assembly installation bolts from the front crossmember, then
suspend the steering gear and linkage with a cable.
Tightening torque
• Steering gear and linkage: 74.4—104.8 N·m {7.857—10.68 kgf·m, 54.88—77.29 ft·lbf}
• Pipe assembly: 7.8—10.8 N·m {79.6—110.0 kgf·cm, 69.1—95.5 in·lbf}
6. Remove in the order indicated in the table.
7. Install in the reverse order of removal.
8. Adjust the headlight zeroset.
(See
.)
9. Inspect the front wheel alignment.
(See
A6E7414W021
R–24
FRONT SUSPENSION
.
A6E7414W100
1
Nut (stabilizer control link)
2
Front lower arm (front) ball joint
(See
R–16 Front Lower Arm (Front) Ball Joint
3
Front lower arm (rear) ball joint
(See
R–19 Front Lower Arm (Rear) Ball Joint
4
Bolt (front shock absorber lower side)
5
No.1 engine mount center bolt
(See
R–25 No.1 Engine Mount Center Bolt Removal
)
6
Crossmember bracket
(See
R–25 Crossmember Bracket Removal Note
7
Crossmember component
8
Stabilizer bracket and bushing
9
Front Stabilizer
10
Front lower arm (front)
11
Front lower arm (rear)
12
Front crossmember
13
Front crossmember bushing
(See
R–25 Front Crossmember Bushing Removal
(See
FRONT SUSPENSION
R–25
R
No.1 Engine Mount Center Bolt Removal Note
1. Suspend the engine using the SST.
2. Remove the No.1 engine mount center bolt.
Crossmember Bracket Removal Note
Warning
• Removing the crossmember is dangerous. The crossmember component could fall and cause
serious injury or death. Verify that the jack securely supports the crossmember component before
removing the crossmember bracket.
1. Support the crossmember component with a jack
and remove the nuts.
2. Remove the crossmember bracket.
Front Crossmember Bushing Removal Note
1. Mark the crossmember as shown in the figure
(rear upper side only).
2. Remove the bushings using screw driver (-),
being care not to damage the front crossmember.
A6E7414W016
A6E7414W036
A6E7414W040
A6E7414W032
R–26
FRONT SUSPENSION
Front Crossmember Bushing Installation Note
1. Set the bushings as shown in the figure.
2. Install the bushing onto the crossmember using
the SSTs.
End Of Sie
A6E7414W041
A6E7414W042
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст