Mazda 6. Manual — part 305
S–114
SEAT
End Of Sie
REMOTE HANDLE LEVER REMOVAL/INSTALLATION
A6E775200166W01
4SD
1. To remove the remote wire, remove the trunk side trim.
2. Remove in the order indicated in the table.
3. Install in the reverse order of removal.
5HB
1. To remove the remote wire, remove the trunk side upper trim and trunk side trim.
2. Remove in the order indicated in the table.
3. Install in the reverse order of removal.
End Of Sie
1
Remote handle lever
2
Remote wire
3
Remote catch
A6E7752W005
1
Remote handle lever
2
Cover
3
Remote wire
A6E7752W011
SEAT
S–115
S
SEAT BACK STRIKER REMOVAL/INSTALLATION
A6E775262361W01
1. Remove the tire house trim.
2. Remove the trunk side upper trim and trunk side lower trim.
3. Remove the bolts.
4. Remove the seat back striker.
5. Install in the reverse order of removal.
End Of Sie
POWER SEAT SWITCH INSPECTION
A6E775257155W01
1. Disconnect the power seat switch connector.
2. Disconnect the rear tilt motor connector.
3. Inspect for continuity between the power seat switch connector terminals using an ohmmeter.
• If not as specified, replace the power seat switch.
A6E7752W016
A6E7752W029
S–116
SEAT
End Of Sie
FRONT TILT MOTOR INSPECTION
A6E775288650W01
1. Disconnect the front tilt motor connector.
2. Inspect the front tilt motor operation when B+ is
applied to the terminals as shown.
• If not as specified, replace the seat cushion
frame.
( ) : R.H.D.
End Of Sie
REAR TILT MOTOR INSPECTION
A6E775288651W01
1. Disconnect the rear tilt motor connector.
2. Inspect the rear tilt motor operation when B+ is
applied to the terminals as shown.
• If not as specified, replace the seat cushion
frame.
( ) : R.H.D.
End Of Sie
SLIDE MOTOR INSPECTION
A6E775288662W01
1. Disconnect the slide motor connector.
2. Inspect the slide motor operation when B+ is
applied to the terminals as shown.
• If not as specified, replace the seat cushion
frame.
End Of Sie
RECLINER MOTOR INSPECTION
A6E775288663W01
1. Disconnect the recliner motor connector.
2. Inspect the recliner motor operation when B+ is
applied to the terminal as shown.
• If not as specified, replace the seat cushion
frame.
End Of Sie
Motor operation
Connection
B+
GND
Up
A
(B)
B
(A)
Down
B
(A)
A
(B)
A6E7752W008
Motor operation
Connection
B+
GND
Up
A
(B)
B
(A)
Down
B
(A)
A
(B)
A6E7752W009
Motor operation
Connection
B+
GND
Forward
A
B
Backward
B
A
A6E7752W010
Motor operation
Connection
B+
GND
Forward
B
A
Backward
A
B
A6E7752W028
SEAT
S–117
S
SEAT WARMER SWITCH REMOVAL/INSTALLATION
A6E775259000W01
1. Disconnect the negative battery cable.
2. Remove the brake boots panel. (See
.)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
Seat Warmer Switch Removal Note
1. Squeeze the tabs of seat warmer switch and pull it forward to remove it.
End Of Sie
SEAT WARMER SWITCH INSPECTION
A6E775259000W02
1. Remove the seat warmer switch.
2. Inspect for continuity between the seat warmer switch terminals using an ohmmeter.
• If not as specified, replace the seat warmer switch.
Driver’s side
Passenger’s side
End Of Sie
1
S–117 Seat Warmer Switch Removal Note
.)
2
Connector
A6E7752W001
A6E7752W024
A6E7752W025
A6E7752W024
A6E7752W026
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст