Mazda 6. Manual — part 229
M–26
DRIVE SHAFT
Dynamic Damper Assembly Note
1. Install the dynamic damper as shown in the
figure.
Standard length
334.7—340.7 mm {13.2—13.4 in}
2. Install the new boot band onto the dynamic
damper.
Boot Assembly Note
Note
• The wheel side and transaxle side boots are different.
1. Fill the boot (wheel side) with the specified grease.
Caution
• Do not touch grease with your hand. Apply it from the tube to prevent foreign matter from entering
the boot.
Grease amount
90—110 g {3.18—3.88 oz} (L8, LF left side)
105—125 g {3.71—4.40 oz} (L8, LF right side and L3)
2. With the splines of the shaft still wrapped in tape from disassembly, install the boot.
3. Remove the tape.
Cage, Inner Ring, Balls, Snap Ring Assembly Note
1. Align the marks and install the balls and cage to
the inner ring in the direction shown in the figure.
Caution
• Install the cage with the offset facing the
snap ring groove. If incorrectly installed,
the drive shaft may become disengaged.
2. Install a new snap ring.
Outer Ring, Clip Assembly Note
1. Fill the outer ring and boot (transaxle side) with the specified grease.
Caution
• Do not touch grease with your hand. Apply it from the tube to prevent foreign matter from entering
the boot.
Grease amount
105—125 g {3.71—4.40 oz} (L8, LF left side),
120—140 g {4.24—4.93 oz} (L8, LF right side and L3)
2. Align the marks, and install the outer ring on to the shaft.
3. Install a new clip.
4. Install the boot.
5. Set the drive shaft to the standard length.
A6E6316W006
A6E6316W011
DRIVE SHAFT
M–27
M
Standard length
mm {in}
6. Release any trapped air from the boots by
carefully lifting up the small end of each boot with
a cloth wrapped screwdriver.
Caution
• Be careful not to allow the grease to leak.
• Do not damage the boot.
7. Verify that the drive shaft length is within the
specification.
End Of Sie
Left side
Right side
L8, LF
677.7—687.7
{26.69—27.07}
628.6—638.6
{24.75—25.14}
L3
676.6—686.6
{26.64—27.03}
A6E6316W007
N–1
N
N
STEERING SYSTEM
LOCATION INDEX . . . . . . . . . . . . .N-2
STEERING LOCATION INDEX . . . . . . ...N-2
GENERAL PROCEDURES . . . . . . . . . N-3
PRECAUTION (STEERING). . . . . . . . N-3
INSPECTION . . . . . . . . . . . . . N-6
REMOVAL/INSTALLATION . . . . . . . ..N-7
STEERING SHAFT INSPECTION . . . . . ...N-9
STEERING GEAR AND LINKAGE
REMOVAL/INSTALLATION . . . . . . . N-10
DISASSEMBLY. . . . . . . . . . . ...N-12
INSPECTION . . . . . . . . . . . . ..N-16
ASSEMBLY. . . . . . . . . . . . . .N-16
N–2
LOCATION INDEX
STEERING LOCATION INDEX
A6E660001036W01
.
End Of Sie
LOCATION INDEX
A6E0610W010
1
Power steering fluid
(See
2
Steering wheel and column
(See
(See
)
3
Steering shaft
(See
4
Steering gear and linkage
(See
N–10 STEERING GEAR AND LINKAGE
(See
N–12 STEERING GEAR AND LINKAGE
(See
N–16 STEERING GEAR AND LINKAGE
)
(See
N–16 STEERING GEAR AND LINKAGE
5
Power steering oil pump
(See
(See
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст