Mazda 6. Manual — part 223
M–2
LOCATION INDEX
FRONT AXLE/DRIVE SHAFT LOCATION INDEX
A6E630004000W01
.
End Of Sie
LOCATION INDEX
A6E0612W106
1
Hub bolt
(See
M–4 WHEEL HUB BOLT REPLACEMENT
2
Wheel hub, steering knuckle
(See
M–4 WHEEL HUB, STEERING KNUCKLE
)
(See
M–5 WHEEL HUB, STEERING KNUCKLE
)
3
Joint shaft
(See
M–12 JOINT SHAFT PRE-INSPECTION
)
(See
(See
)
4
Drive shaft
(See
M–16 DRIVE SHAFT PRE-INSPECTION
(See
)
(See
M–19 DRIVE SHAFT (ATX) DISASSEMBLY/
(See
LOCATION INDEX, GENERAL PROCEDURES
M–3
M
REAR AXLE LOCATION INDEX
A6E630005000W01
.
End Of Sie
PRECAUTION (FRONT AND REAR AXLE)
A6E631001018W01
Wheel and Tire Removal/Installation
1. The removal and installation procedures for the wheels and tires are not mentioned in this section. When a
wheel is removed, tighten it to 88—118 N·m {9.0—12.0 kgf·m, 65.0—87.0 ft·lbf}
Brake Line Disconnection/Connection
Caution
• Brake fluid will damage painted surfaces. If brake fluid gets on a painted surface, wipe it off
immediately.
1. Tighten the brake pipe flare nut using the SST (49 0259 770B). Be sure to modify the brake pipe flare nut
tightening torque to allow for use of a torque wrench-SST combination. (See
2. If any brake line has been disconnected any time during the procedure, add brake fluid, bleed the brakes, and
inspect for leakage after the procedure has been completed.
Suspension Arm Removal/Installation
1. Tighten any part of the suspension that uses rubber bushings only after vehicle has been lowered and
unloaded.
Note
• Unloaded: Fuel tank is full. Engine coolant and engine oil are at specified level. Spare tire, jack, and tools
are in designated position.
End Of Sie
A6E0312W016
1
M–9 WHEEL HUB, HUB SPINDLE PRE-
)
GENERAL PROCEDURES
M–4
FRONT AXLE
WHEEL HUB, STEERING KNUCKLE PRE-INSPECTION
A6E631204000W01
Wheel Bearing Play Inspection
1. Position a dial indicator against the wheel hub.
2. Push and pull the wheel hub by hand in the axial
direction and measure the wheel bearing play.
Maximum wheel bearing play
0.05 mm {0.002 in}
3. If the bearing play exceeds the specification,
replace and tighten the locknut to the specified
torque and retest.
• Replace the wheel bearing as necessary.
End Of Sie
WHEEL HUB BOLT REPLACEMENT
A6E631233060W01
1. Remove the hub bolt using the SSTs.
Note
• If the dust cover interferes with the wheel
hub bolt and the wheel hub bolt cannot be
removed, tap the part shown in the figure
with a chisel lightly and bend the processing
point back to the steering knuckle side.
2. Install the hub bolt into the wheel hub and install a
washer and hub nut on the hub bolt.
3. Tighten the hub nut while holding the wheel hub
using a brass bar.
End Of Sie
FRONT AXLE
A6E0311W010
A6E0311W011
A6E0311W012
FRONT AXLE
M–5
M
WHEEL HUB, STEERING KNUCKLE REMOVAL/INSTALLATION
A6E631204000W02
Caution
• Performing the following procedures without first removing the ABS wheel-speed sensor may
possibly cause an open circuit in the harness if it is pulled by mistake. Before performing the
following procedures, remove the ABS wheel-speed sensor (axle side) and fix it to an appropriate
place where the sensor will not be pulled by mistake while the vehicle is being serviced.
1. Remove in the order indicated in the table.
2. Install in the reverse order of removal.
3. After installation, inspect the front wheel alignment. (See
.
A6E0612W075
1
)
2
Brake caliper component
3
4
N–11 Tie-rod End Ball Joint Removal Note
5
Bolt
6
Front lower arm (front) ball joint
(See
R–16 Front Lower Arm (Front) Ball Joint
7
Front lower arm (rear) ball joint
(See
R–19 Front Lower Arm (Rear) Ball Joint
8
Front upper arm ball joint
(See
R–13 Front Upper Arm Ball Joint Removal
9
Wheel hub, steering knuckle, dust cover
10
Wheel hub component
(See
M–6 Wheel Hub Component Removal Note
(See
M–8 Wheel Hub Component Installation Note
11
Retaining ring
12
Wheel bearing
(See
M–6 Wheel Bearing Removal Note
(See
M–8 Wheel Bearing Installation Note
13
Dust cover
(See
)
(See
M–8 Dust Cover Installation Note
14
Steering knuckle
15
Hub bolt
(See
(See
M–7 Hub Bolt Installation Note
)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст