Mazda 6. Manual — part 315
T–20
POWER SYSTEM
FUSE BLOCK REMOVAL/INSTALLATION
A6E811066730W01
1. Disconnect the negative battery cable.
2. Remove the left-side front side trim. (See
S–88 FRONT SIDE TRIM REMOVAL/INSTALLATION
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
End Of Sie
IGNITION SWITCH REMOVAL/INSTALLATION
A6E811066151W01
1. Disconnect the negative battery cable.
2. Remove the column cover. (See
S–84 COLUMN COVER REMOVAL/INSTALLATION
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
End Of Sie
IGNITION SWITCH INSPECTION
A6E811066151W02
1. Disconnect the negative battery cable.
2. Remove the column cover. (See
S–84 COLUMN COVER REMOVAL/INSTALLATION
3. Disconnect the ignition switch connectors.
4. Inspect for continuity between the ignition switch
terminals using an ohmmeter.
• If not as specified, replace the ignition switch.
End Of Sie
1
Connector
2
Bolt
3
Fuse block
A6E8110W107
1
Connector
2
Screw
3
Ignition switch
A6E8110W101
A6E8110W116
A6E8110W114
POWER SYSTEM
T–21
T
KEY REMINDER SWITCH REMOVAL/INSTALLATION
A6E811066152W01
1. Disconnect the negative battery cable.
2. Remove the column cover.
3. Disconnect the key reminder switch connector.
4. Remove the key reminder switch.
5. Install in the reverse order of removal.
End Of Sie
KEY REMINDER SWITCH INSPECTION
A6E811066152W02
1. Disconnect the negative battery cable.
2. Remove the column cover. (See
S–84 COLUMN COVER REMOVAL/INSTALLATION
3. Disconnect the key reminder switch connector.
4. Inspect for continuity between the key reminder
switch terminals using an ohmmeter.
• If not as specified, replace the key reminder
switch.
End Of Sie
CIGARETTE LIGHTER REMOVAL/INSTALLATION
A6E811067000W01
1. Disconnect the negative battery cable.
2. Remove in the order indicated in the table.
3. Install in the reverse order of removal.
A6E8110W102
A6E8110W117
A6E8110W115
1
Cigarette lighter plug
2
Connector
3
)
4
)
A6E8110W103
T–22
POWER SYSTEM
Socket Removal Note
1. Insert a tape-wrapped screwdriver into the socket
hole, then press against the ring protrusion to lift
the socket toward you.
2. As shown in the figure, lift out the socket until the
ring protrusion locks into the lower socket hole.
3. Remove the boot panel.
4. From behind the boot panel, slide a tape-wrapped
screwdriver in between the socket and the ring
protrusion..
5. While twisting the ring protrusion with the
screwdriver, push out and remove the socket.
Ring Removal Note
1. Pull the ring forward while compressing the
hooks.
End Of Sie
CIGARETTE LIGHTER INSPECTION
A6E811067000W02
1. Turn the ignition switch to ACC position.
2. Verify that the cigarette lighter comes out within 10—20 seconds, after pressing the plug into the socket.
• If the cigarette lighter does not operate normally, replace the cigarette lighter plug and socket.
End Of Sie
A6E8110W104
A6E8110W106
A6E8110W201
A6E8110W105
POWER SYSTEM
T–23
T
RELAY LOCATION
A6E811067730W01
.
End Of Sie
A6E8110T102
1
Cooling fan relay No.2
2
Horn relay
3
Cooling fan relay No.3
4
Stater relay
5
Cooling fan relay No.4
6
Woofer relay
7
Rear window defroster relay
8
Rear fog light relay
9
A/C relay
10
Main relay
11
Headlight relay
12
TNS relay
13
Cooling fan relay No.1
14
Headlight cleaner relay
15
Front fog light relay
16
Fuel pump relay
17
Blower relay
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст