Mazda 6. Manual — part 132
F–50
CONTROL SYSTEM
PCM CONFIGURATION
A6E394018880W03
1. Connect the WDS to DLC-2.
2. Set up the WDS (including the vehicle
recognition.)
3. Select “Module programming.”
4. Select “Programmable module installation.”
5. Select “PCM” and perform procedures according
to directions on the WDS screen.
Note
• If “PCM CONFIGURATION” is successful,
the PCM stores the DTC P0602 and
illuminates the MIL. (System is normal.)
Clear the DTC P0602 using WDS or
equivalent after “PCM CONFIGURATION.”
Note
• MIL goes off after three drive cycles with no failure. (DTCs remain in PCM.)
6. Retrieve DTC’s by the WDS or equivalent, then verify that there in no DTC present.
• If DTC is present, perform applicable DTC inspection.
End Of Sie
INTAKE AIR TEMPERATURE (IAT) SENSOR INSPECTION
A6E394018845W01
Resistance Inspection
Note
• Perform the following inspection only when directed.
1. Disconnect MAF/IAT sensor.
2. Measure the resistance between the MAF/IAT
sensor terminals D and E using an ohmmeter.
• If not as specified, replace the MAF/IAT
sensor.
• If the MAF/IAT sensor is okay, but the IAT PID
are out of specification, perform the “Circuit
Open/Short Inspection”.
Specification
Circuit Open/Short Inspection
1. Disconnect the PCM connector. (See
2. Inspect the following wiring harnesses for open or
short. (Continuity check)
Open circuit
• If there is no continuity, the circuit is open. Repair
or replace the harness.
— MAF/IAT sensor terminal D (harness-side)
and PCM terminal 2E (harness-side)
— MAF/IAT sensor terminal E (harness-side)
and PCM terminal 2H (harness-side)
Short circuit
• If there is continuity, the circuit is shorted. Repair
or replace the harness.
— MAF/IAT sensor terminal E (harness-side) and power supply
— MAF/IAT sensor terminal D (harness-side) and power supply
— MAF/IAT sensor terminal D (harness-side) and body GND
End Of Sie
DLC-2
A6E3970W002
Ambient temperature (
°C {°F})
Resistance (kilohm)
–20 {–4}
13.6—18.4
20 {68}
2.21—2.69
60 {140}
0.493—0.667
A6E3940W005
A6E3940W006
CONTROL SYSTEM
F–51
F
MASS AIR FLOW (MAF) SENSOR INSPECTION
A6E394013210W01
Voltage Inspection
Note
• Perform the following inspection only when directed.
1. Visually inspect for the following on the MAF sensor.
• Damage
• Cracks
• Terminal bends
• Terminal rust
— If any of the above are found, replace the MAF sensor.
— If the MAF PID value is out of specification, carry out the “Circuit Open/Short Inspection”.
Circuit Open/Short Inspection
1. Disconnect the PCM connector. (See
2. Disconnect the MAF sensor connector.
3. Inspect the following wiring harnesses for open or
short. (Continuity check)
Open circuit
• If there is no continuity, the circuit is open. Repair
or replace the harness.
— MAF sensor terminal A (harness-side) and
main relay terminal C (harness-side)
— MAF sensor terminal B (harness-side) and
PCM terminal 2AC (harness-side)
— MAF sensor terminal C (harness-side) and
PCM terminal 1P (harness-side)
Short circuit
• If there is continuity, the circuit is shorted. Repair or replace the harness.
— MAF sensor terminal A (harness-side) and body GND
— MAF sensor terminal C (harness-side) and power supply
— MAF sensor terminal C (harness-side) and body GND
— MAF sensor terminal B (harness-side) and power supply
End Of Sie
THROTTLE POSITION (TP) SENSOR INSPECTION
A6E394018910W01
Note
• Perform the following inspection only when directed.
Resistance Inspection
1. Perform the following test only when directed.
• If as specified but TP PID value is out of specification, inspect resistance of TP sensor.
• If not as specified, inspect the following:
— Accelerator cable free play (See
F–16 ACCELERATOR CABLE INSPECTION/ADJUSTMENT
2. Disconnect the TP sensor connector.
3. Verify that the resistance between TP sensor
terminals A and B changes smoothly while
opened and closed the throttle valve slowly.
• If not verified, replace TP sensor.
4. Measure the resistance between TP sensor
terminals A and C using an ohmmeter.
• If not as specified, replace the TP sensor.
• If as specified, but TP PID value is out of
specification, perform the “Circuit Open/Short
Inspection”.
Specification
3.2—4.8 kilohms
A6E3940W006
A6E3940W007
F–52
CONTROL SYSTEM
Circuit Open/Short Inspection
1. Disconnect the PCM connector. (See
2. Inspect the following wiring harnesses for open or
short. (Continuity check)
Open circuit
• If there is no continuity, the circuit is open. Repair
or replace the harness.
— TP sensor terminal A (harness-side) and
PCM terminal 2H (harness-side)
— TP sensor terminal B (harness-side) and
PCM terminal 2A (harness-side)
— TP sensor terminal C (harness-side) and
PCM terminal 2K (harness-side)
Short circuit
• If there is continuity, the circuit is shorted. Repair or replace the harness.
— TP sensor terminal C (harness-side) and power supply
— TP sensor terminal C (harness-side) and body GND
— TP sensor terminal B (harness-side) and power supply
— TP sensor terminal B (harness-side) and body GND
— TP sensor terminal A (harness-side) and power supply
End Of Sie
MANIFOLD ABSOLUTE PRESSURE (MAP) SENSOR INSPECTION
A6E394018211W01
Note
• Perform the following inspection only when directed.
• The following vacuum values are indicated by relative pressure from the MAP sensor.
1. Connect the SSTs (WDS or equivalent) to the DLC-2.
2. Turn the ignition switch to ON (Engine OFF).
3. Select MAP PID on the SSTs (WDS or equivalent).
4. Verify that the MAP PID (pressure) and barometric pressure are practically equal.
• If not as verified, perform the “Circuit Open/Short Inspection”.
— If there is no open or short circuit, replace the MAP sensor.
• If as verified, go to next step.
5. Apply vacuum of –25.0 kPa {–187 mmHg, –7.38 inHg} to the MAP sensor, and verify that the MAP variation
from that of Step 4 is approx. 25.0 kPa {187 mmHg, 7.38 inHg}.
• If not as verified, perform the “Circuit Open/Short inspection”.
— If there is no open or short circuit, replace the barometric pressure sensor.
Circuit Open/Short Inspection
1. Disconnect the PCM connector. (See
2. Inspect the following wiring harness for open or
short. (Continuity check)
Open circuit
• If there is no continuity, the circuit is open. Repair
or replace the harness.
— MAP sensor terminal A (harness-side) and
PCM terminal 2H
— MAP sensor terminal D (harness-side) and
PCM terminal 1J
— MAP sensor terminal C (harness-side) and
PCM terminal 2K
Short circuit
• If there is continuity, the circuit is shorted. Repair or replace the harness.
— MAP sensor terminal C (harness-side) and power supply.
— MAP sensor terminal C (harness-side) and body GND.
— MAP sensor terminal D (harness-side) and power supply.
— MAP sensor terminal D (harness-side) and body GND
End Of Sie
A6E3940W008
A6E3940W009
CONTROL SYSTEM
F–53
F
ENGINE COOLANT TEMPERATURE (ECT) SENSOR REMOVAL/INSTALLATION
A6E394018840W01
Warning
• When the engine is hot, it can badly burn. Turn off the engine and wait until it is cool before
removing the ECT sensor.
1. Drain the engine coolant. (See
E–3 COOLING SYSTEM SERVICE WARNINGS
.)
2. Disconnect the ECT sensor connector.
3. Remove the ECT sensor.
4. Install in the reverse order of removal.
Tightening torque
10—14 N·m
{1.02—1.42 kgf·m, 7.38—10.32 ft·lbf}
5. Refill the engine coolant. (See
End Of Sie
ENGINE COOLANT TEMPERATURE (ECT) SENSOR INSPECTION
A6E394018840W02
Note
• Perform the following inspection only when directed.
ECT Sensor Resistance Inspection
1. Drain the engine coolant. (See
E–3 COOLING SYSTEM SERVICE WARNINGS
.)
2. Remove the ECT sensor (located above the starter).
3. Place the ECT sensor in water with a thermometer, and heat the water gradually.
4. Measure the resistance between the ECT sensor terminals A and B using an ohmmeter.
• If not as specified, replace the ECT sensor.
• If the ECT sensor is okay, but ECT PID value is out of specification, perform the “Circuit Open/Short
Inspection”.
Specification
Circuit Open/Short Inspection
1. Disconnect the PCM connector. (See
2. Inspect the following wiring harnesses for open or
short. (Continuity check)
Open circuit
• If there is no continuity, the circuit is open. Repair
or replace the harness.
— ECT sensor terminal A (harness-side) and
PCM terminal 1M (harness-side)
— ECT sensor terminal B (harness-side) and
PCM terminal 2H (harness-side)
Short circuit
• If there is continuity, the circuit is shorted. Repair
or replace the harness.
— ECT sensor terminal A (harness-side) and power supply
— ECT sensor terminal A (harness-side) and body GND
A6E3940W010
Water temperature (
°C {°F})
Resistance (kilohms)
20 {68}
35.48—39.20
70 {158}
5.07—5.60
80 {176}
3.65—4.02
A6E3940W011
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст