Mazda 6. Manual — part 192
AUTOMATIC TRANSAXLE
K–13
K
AUTOMATIC TRANSAXLE FLUID (ATF) REPLACEMENT
A6E561401030W04
Warning
• When the transaxle and ATF are hot, they can badly burn you. Turn off the engine and wait until
they are cool before changing the ATF.
1. Remove the oil dipstick.
2. Remove the oil drain plug and washer.
3. Drain the ATF into a container.
4. Install a new washer and the drain plug.
Tightening torque
30—41 N·m {3.0—4.2 kgf·m, 22—30 ft·lbf}
5. Add the specified ATF until ATF level reaches
lower notch of dipstick type of ATF through the oil
filler tube.
ATF type
ATF M-V
6. Ensure that the ATF level is in the HOT range (65
°C{149 °F}).
• Add ATF to the specified level as necessary.
End Of Sie
HOLD SWITCH INSPECTION
A6E561446030W01
Operating Inspection
1. Turn the ignition switch to ON (engine OFF).
2. Verify that the HOLD indicator light is not illuminated. Depress the HOLD switch and verify that the HOLD
indicator light illuminates.
• If not as specified, inspect the terminal voltage of the HOLD switch.
Voltage Inspection
1. Remove the console.
2. Turn the ignition switch to ON (engine OFF).
3. Measure the voltage at the HOLD switch
connector.
• If not as specified, inspect for continuity at the
HOLD switch.
A6E5614W005
HOLD switch
position
Connector terminal
C
D
Normal
B+
0
Depressed
0
0
A6E5614W006
K–14
AUTOMATIC TRANSAXLE
Continuity Inspection of
1. Disconnect the negative battery cable.
2. Remove the console.
3. Disconnect the HOLD switch connector.
4. Inspect continuity at the HOLD switch.
• If the switch is okay, inspect the wiring
harness. (HOLD switch—PCM, HOLD
switch—Body ground)
• If not as specified, replace the HOLD switch.
(See
5. Connect the HOLD switch connector.
6. Install the console.
7. Connect the negative battery cable.
End Of Sie
HOLD SWITCH REMOVAL/INSTALLATION
A6E561446030W02
1. Disconnect the negative battery cable.
2. Remove the console.
3. Disconnect the connector and remove the HOLD switch terminals. (See
4. Remove the selector lever knob component.
5. Remove the HOLD switch.
6. Install the HOLD switch to selector lever knob component.
7. Install selector lever knob component.
Tightening torque
15.68—22.54 N·m {1.599—2.298 kgf·m, 12—16 ft·lbf}
8. Install the HOLD switch terminals and connect the connector.
9. Install the console.
10. Connect the negative battery cable.
End Of Sie
TRANSAXLE RANGE (TR) SWITCH INSPECTION
A6E561419440W01
Operating Inspection
1. Verify that the starter operates only when the ignition switch is at the START position with the selector lever in P
or N position.
• If not as specified, adjust the TR switch.
2. Verify that the back-up lights illuminate when shifted to R position with the ignition switch at the ON position.
• If not as specified, adjust the TR switch.
Continuity Inspection
Caution
• Water or foreign objects entering the connector can cause a poor connection or corrosion. Be
sure not to drop water or foreign objects on the connector when disconnecting it.
1. Disconnect the negative battery cable.
2. Remove the air cleaner component. (See
F–10 INTAKE-AIR SYSTEM REMOVAL/INSTALLATION
A6E5614W007
AUTOMATIC TRANSAXLE
K–15
K
3. Disconnect the TR switch connector.
4. Inspect for continuity at the TR switch.
• If not as specified, adjust the TR switch and
go to Step 4.
5. Reinspect for continuity at TR switch.
• If not as specified, replace the TR switch.
(See
6. Connect the TR switch connector.
7. Install the air cleaner component. (See
INTAKE-AIR SYSTEM REMOVAL/
INSTALLATION
8. Connect the negative battery cable.
End Of Sie
TRANSAXLE RANGE (TR) SWITCH REMOVAL/INSTALLATION
A6E561419440W02
1. Disconnect the negative battery cable.
2. Remove the air cleaner component. (See
F–10 INTAKE-AIR SYSTEM REMOVAL/INSTALLATION
Caution
• Water or foreign objects entering the connector can cause a poor connection or corrosion. Be
sure not to drop water or foreign objects on the connector when disconnecting it.
3. Disconnect the TR switch connector.
4. Remove the clip and disconnect the selector
cable.
Caution
• Do not use an impact wrench. Hold the
manual shaft lever when removing the
manual shaft nut, or the transaxle may be
damaged.
5. Set the adjustable wrench as shown to hold the
manual shaft lever.
6. Remove the manual shaft nut and washer.
A6E5614W008
A6E5614W010
A6E5614W011
A6E5614W100
K–16
AUTOMATIC TRANSAXLE
7. Remove the manual shaft lever.
8. Remove the TR switch.
9. Rotate the manual shaft to the converter housing
side fully, then return 2 notches to set the N
position.
10. Turn the protrusion at resistance between the
terminals B and C become 750 ohms.
11. Install the TR switch while aligning the protrusion
and groove as shown.
12. Hand-tighten the TR switch mounting bolts.
A6E5614W012
A6E5614W013
A6E5614W014
A6E5614W010
A6E5614W016
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст