Mazda 6. Manual — part 107
CYLINDER HEAD GASKET, FRONT OIL SEAL
B–21
B
Camshaft Installation Note
1. Set the cam position of the No.1 cylinder at the
top dead center (TDC) and install the camshaft.
2. Temporarily tighten the camshaft bearing caps in
two or three even movements.
3. Tighten the camshaft cap bolts in the order shown
using the following two steps.
(1) Tighten to 5.0—9.0 N·m {51.0—91.7 kgf·cm,
44.6—79.5 in·lbf}
(2) Tighten to 14.0—17.0 N·m {1.5—1.7 kgf·m,
10.4—12.5 ft·lbf}
End Of Sie
FRONT OIL SEAL REPLACEMENT
A6E222010602W01
1. Disconnect the negative battery cable.
2. Remove the spark plugs. (See
G–10 SPARK PLUG REMOVAL/INSTALLATION
3. Remove the Cylinder head cover. (See
B–17 Cylinder Head Cover Installation Note
.)
4. Remove the drive belt. (See
5. Remove the front drive shaft (RH) from the joint shaft. (See
M–17 DRIVE SHAFT REMOVAL/INSTALLATION
6. Remove the CKPsensor.(See
F–54 CRANKSHAFT POSITION (CKP) SENSOR REMOVAL/INSTALLATION
7. Remove in the order indicated in the table.
8. Install in the reverse order of removal.
.
AME2212W009
FRONT OIL SEAL
AME2220W001
1
Crankshaft pulley lock bolt
(See
B–22 Crankshaft Pulley Lock Bolt Removal
B–23 Crankshaft Pulley Lock Bolt Installation
2
Crankshaft pulley
3
Front oil seal
(See
B–22 Front Oil Seal Removal Note
(See
B–23 Front Oil Seal Installation Note
)
B–22
FRONT OIL SEAL
Crankshaft Pulley Lock Bolt Removal Note
1. Remove the cylinder block lower blind plug.
2. Install the SST.
3. Turn the crankshaft clockwise the crankshaft is in
the No.1 cylinder TDC position.
4. Hold the crankshaft pulley by using the SSTs.
Front Oil Seal Removal Note
1. Cut the oil seal lip using a razor knife.
2. Remove the oil seal using a screwdriver protected
with a rag.
AME2212W004
AME2215W002
AME2220W002
FRONT OIL SEAL
B–23
B
Front Oil Seal Installation Note
1. Apply clean engine oil to the oil seal lip.
2. Push the oil seal slightly in by hand.
3. Tap the oil seal in evenly using the SST and a
hammer.
Crankshaft Pulley Lock Bolt Installation Note
1. Install the SST to the camshaft as shown.
European countries
Except European countries
AME2215W009
AME2215W010
AME2212W010
AME2212W011
B–24
FRONT OIL SEAL
2. Install the M6 x 1.0 bolt in by hand.
3. Turn the crankshaft clockwise the crankshaft is in
the No.1 cylinder TDC position.
4. Hold the crankshaft pulley by using the SSTs.
5. Tighten the crankshaft pulley lock bolt in the order
shown using the following two steps.
(1) Tighten to 96—104 N·m {9.8—10.6 kgf·m,
70.9—76.7 ft·lbf}
(2) Tighten 87
°—93°
6. Remove the M6 x 1.0 bolt.
7. Remove the SST from the camshaft.
8. Remove the SST from the cylinder block lower
blind plug.
9. Rotate the crankshaft clockwise two turns until
the TDC position.
• If not aligned, loosen the crankshaft pulley
lock bolt and repeat from Step 1.
10. Install the cylinder block lower blind plug.
Tightening torque:
18—22 N·m {1.9—2.2 kgf·m, 13.3—16.2 ft·lbf}
End Of Sie
AME2215W013
AME2215W002
AME2212W012
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст