Mazda 6. Manual — part 278
LOCATION INDEX
S–7
S
Rear
.
21
S–116 RECLINER MOTOR INSPECTION
22
S–115 POWER SEAT SWITCH INSPECTION
23
Seat warmer unit
(See
S–118 SEAT WARMER UNIT INSPECTION
A6E7700W004
1
)
S–61 REARVIEW MIRROR INSTALLATION
)
)
)
2
S–81 SUNROOF SWITCH INSPECTION
3
S–98 SUNVISOR REMOVAL/INSTALLATION
4
S–97 SHOCK ABSORBING PAD REMOVAL/
5
S–88 B-PILLAR UPPER TRIM REMOVAL/
6
Headliner
(See
)
7
Front seat belt
(See
S–100 FRONT SEAT BELT REMOVAL/
)
(See
)
8
B-pillar lower trim
(See
S–88 B-PILLAR LOWER TRIM REMOVAL/
)
9
Power window subswitch
(See
S–25 POWER WINDOW SWITCH REMOVAL/
)
(See
)
10
Assist handle
(See
)
S–8
LOCATION INDEX
End Of Sie
11
Rear door trim
(See
12
C-pillar trim
(See
13
Rear buckle
(See
14
Trunk side trim
(See
Trunk side upper trim
(See
15
Trunk end trim
(See
16
Rear center seat belt
(See
)
(See
17
Tire house trim
(See
18
Rear scuff plate
(See
S–89 REAR SCUFF PLATE REMOVAL/
)
19
Front floor covering
(See
S–99 FRONT FLOOR COVERING REMOVAL/
)
20
Child restraint seat anchor
(See
S–104 CHILD RESTRAINT SEAT ANCHOR
21
Rear seat
(See
)
(See
22
Remote handle lever
(See
S–114 REMOTE HANDLE LEVER REMOVAL/
)
23
Rear package trim
(See
S–92 REAR PACKAGE TRIM REMOVAL/
)
24
Transmitter
(See
(See
)
LOCATION INDEX
S–9
S
DOOR
A6E770001086W03
.
End Of Sie
A6E7700WH01
1
2
3
S–16 FRONT DOOR GLASS REMOVAL/
4
5
6
7
Front door latch and lock actuator
(See
S–19 FRONT DOOR LATCH AND LOCK
)
8
Rear door latch and lock actuator
(See
)
9
Front outer handle
(See
S–21 FRONT OUTER HANDLE REMOVAL/
)
10
Rear outer handle
(See
S–21 FRONT OUTER HANDLE REMOVAL/
)
11
Front door key cylinder
(See
(See
)
12
Inner handle
(See
)
13
Regulator handle
(See
S–22 REGULATOR HANDLE INSTALLATION
)
14
Power window regulator
(See
)
15
Power window motor
(See
S–29 POWER WINDOW MOTOR REMOVAL/
)
(See
)
S–10
BONNET
BONNET REMOVAL/INSTALLATION
A6E771001084W01
Warning
• Removing the bonnet without supporting can be dangerous. The bonnet may fall and injure you.
Always perform the following procedure with at least another person.
1. Disconnect the windshield washer hose.
2. To remove the bonnet hinge, remove the front
fender panel.
3. To remove the bonnet lock, remove the radiator
grille.
4. To remove the bonnet release cable, remove the
driver-side mud guard.
5. Remove in the order indicated in the table.
6. Install in the reverse order of removal.
7. Adjust the bonnet. (See
Bonnet Release Lever Removal Note
1. Pull the lever.
2. While pushing the tab in the direction of the arrow
using a tape-wrapped, small flathead screwdriver,
disengage it from the dashboard.
Caution
• Remove the bonnet release lever while
taking care not to damage the bonnet
release cable with the flathead
screwdriver.
3. Under the condition in Step 2, pull the bonnet
release lever outward, then remove it from the
lower panel.
End Of Sie
BONNET ADJUSTMENT
A6E771001084W02
Gap Adjustment
1. Remove the front fender.
2. Loosen the bonnet hinge installation bolts and
reposition the bonnet.
3. Tighten the bolts.
BONNET
1
Bonnet insulator
2
Shroud seal weatherstrip
3
Parting seal weatherstrip
4
Bonnet
5
Bonnet hinge
6
Bonnet stay
7
Bonnet switch connector (With theft-deterrent
system)
8
Bonnet lock
9
Bonnet release lever
(See
S–10 Bonnet Release Lever Removal Note
)
10
Bonnet release cable
A6E7710W001
CROSS-SECTIONAL VIEW
LOWER PANEL
TAB
TAB
ADA7710W100
A6E7710W002
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст