Mazda CX-9 (2022 year). Manual in english — page 14

When Driving

Parking Sensor System (Mazda Connect (Type A))

Parking Sensor System (Mazda Connect (Type A))*

The parking sensors use ultrasonic sensors which detect obstructions around the vehicle

when the vehicle is driven at low speeds, such as during garage or parallel parking, and a

buzzer sound and detection indicator notify the driver of the approximate distance from the

vehicle to the surrounding obstruction.

Front corner ultrasonic sensor

Rear ultrasonic

sensor

Rear corner ultrasonic sensor

Front ultrasonic sensor

Some models.

WARNING

Do not rely completely on the parking sensor system and be sure to confirm the safety around

your vehicle visually when driving:

This system can assist the driver in operating the vehicle in the forward and backward

directions while parking. The detection ranges of the sensors are limited, therefore, driving the

vehicle while relying only on the system may cause an accident. Always confirm the safety

around your vehicle visually when driving.

NOTE

^ Do not install any accessories within the detection ranges of the sensors. It may affect the

system operation.

^ Depending on the type of obstruction and the surrounding conditions, the detection range

of a sensor may narrow, or the sensors may not be able to detect obstructions.

^ The system may not operate normally under the following conditions:

^ Mud, ice, or snow is adhering to the sensor area (Returns to normal operation when

removed).

^ The sensor area is frozen (Returns to normal operation when the ice is thawed).

^ The sensor is covered by a hand.

^ The sensor is excessively shocked.

^ The vehicle is excessively tilted.

4-260

*Some models.

When Driving

Parking Sensor System (Mazda Connect (Type A))



Under extremely hot or cold weather conditions.

^ The vehicle is driven on bumps, inclines, gravel, or grass covered roads.

^ Anything which generates ultrasound is near the vehicle, such as another vehicle's

horn, the engine sound of a motorcycle, the air brake sound of a large-sized vehicle, or

another vehicle's sensors.

^ The vehicle is driven in heavy rain or in road conditions causing water-splash.

^ A commercially-available fender pole or an antenna for a radio transmitter is installed

to the vehicle.

^ The vehicle is moving towards a tall or square curbstone.

^ An obstruction is too close to the sensor.

^ Obstructions under the bumper may not be detected. Obstructions that are lower than the

bumper or thin which may have been initially detected may no longer be detected as the

vehicle approaches more closely to the obstruction.

^ The following types of obstructions may not be detected:

^ Thin objects such as wire or rope

^ Things which absorb sonic waves easily such as cotton or snow

^ Angular shaped objects

^ Very tall objects, and those which are wide at the top

^ Small, short objects

^ Always have the system inspected at an Authorized Mazda Dealer if any shock is applied

to the bumpers, even in a minor accident. If the sensors are deviated, they cannot detect

obstructions.



(With front ultrasonic sensor and front ultrasonic corner sensor)

The system may have a malfunction if the beep does not operate or the indicator light

does not illuminate when the parking sensor switch is turned on. Consult an Authorized

Mazda Dealer.



(Without front ultrasonic sensor and front ultrasonic corner sensor)

The system may have a malfunction if the beep does not operate. Consult an Authorized

Mazda Dealer.



(With front ultrasonic sensor and front ultrasonic corner sensor)

The system may have a malfunction if the beep sound which indicates a system

malfunction is heard and the indicator light flashes. Consult an Authorized Mazda Dealer.

^ The beeper which indicates a system malfunction may not be heard if the ambient

temperature is extremely cold, or mud, ice, or snow adheres to the sensor area. Remove

any foreign material from the sensor area.

^ When installing a trailer hitch, consult an Authorized Mazda Dealer.

4-261

When Driving

Parking Sensor System (Mazda Connect (Type A))

▼ Sensor Detection Range

The sensors detect obstructions within the following range.

A: About 55 cm (About 21.6 in)

Rear corner ultrasonic sensor detection range

B: About 55 cm (About 21.6 in)

C: About 100 cm (About 39.3 in)

Front ultrasonic sensor detection range

D: About 150 cm (About 59.0 in)

Rear ultrasonic sensor detection range

Front corner ultrasonic sensor detection range

Viewing distance display

Display

Distance between vehicle and obstruction

Without 360° view monitor

Without front ul-

With front ultra-

Front ultrasonic sen-

Rear ultrasonic sen-

With 360° view

trasonic sensor and

sonic sensor and

sor^*/Front corner

sor/Rear Corner ul-

monitor

front corner ultra-

ultrasonic sensor^*

trasonic sensor

sonic sensor

Green

Front ultrasonic sen-

Rear ultrasonic sen-

sor:

Approx. 100―60 cm

Approx. 150―60 cm

(39.4―23.6 in)

(59.1―23.6 in)

4-262

*Some models.

When Driving

Parking Sensor System (Mazda Connect (Type A))

Display

Distance between vehicle and obstruction

Without 360° view monitor

Without front ul-

With front ultra-

Front ultrasonic sen-

Rear ultrasonic sen-

With 360° view

trasonic sensor and

sonic sensor and

sor^*/Front corner

sor/Rear Corner ul-

monitor

front corner ultra-

ultrasonic sensor^*

trasonic sensor

sonic sensor

Yellow

Front ultrasonic sen-

Rear ultrasonic sen-

sor:

Approx. 60―45 cm

(23.6―17.7 in)

Front corner ultrason-

Rear corner ultrasonic

ic sensor:

sensor:

Approx. 55―38 cm

(21.7―14.9 in)

Amber

Front ultrasonic sen-

Rear ultrasonic sen-

sor:

Approx. 45―35 cm

(17.7―13.8 in)

Front corner ultrason-

Rear corner ultrasonic

ic sensor:

sensor:

Approx. 38―25 cm

(15―9.8 in)

Red

Front ultrasonic sen-

Rear ultrasonic sen-

sor:

Within approx. 35 cm

(13.8 in)

Front corner ultrason-

Rear corner ultrasonic

ic sensor:

sensor:

Within approx. 25 cm

(9.8 in)

*Some models.

4-263

When Driving

Parking Sensor System (Mazda Connect (Type A))

▼ Parking Sensor System Operation

With front ultrasonic sensor and front corner ultrasonic sensor

The switch can be activated when the ignition is switched ON, the selector lever is in any

position except reverse (R), and the vehicle speed is about 10 km/h (6 mph) or less.

When the parking sensor switch is pressed, a beep sound is heard, the obstruction detection

indication is displayed in the audio screen, and the indicator light in the switch illuminates.

Indicator light

NOTE

^ If the system is cancelled, it will not restore automatically even when the vehicle speed is

decreased to 10 km/h (6 mph) or less.

^ When the ignition is switched OFF, the system status before it was turned off is

maintained. For example, if the ignition is switched OFF while the parking sensor is

activated, the system will be activated when the ignition is switched ON the next time.

Sensor detection condition

The system can be used when the ignition is switched ON and the parking sensor switch has

been turned on.

The sensors detect obstructions under the following conditions:

Sensor

Condition

The selector lever is in any position except reverse (R), and the vehicle speed is

Front Ultrasonic Sensor

about 10 km/h (6 mph) or less.

Front Corner Ultrasonic

The vehicle speed is about 10 km/h (6 mph) or less.

Sensor

Rear Ultrasonic Sensor

The selector lever is in reverse (R).

Rear Corner Ultrasonic

The selector lever is in reverse (R), and the vehicle speed is about 10 km/h (6 mph)

Sensor

or less.

The system is cancelled under the following conditions:

4-264

When Driving

Parking Sensor System (Mazda Connect (Type A))



The parking sensor switch is pressed while the parking sensor is in operation.

^ The vehicle speed is 10 km/h (6 mph) or more. (Except rear sensor)

Without front ultrasonic sensor and front corner ultrasonic sensor

When the ignition is switched ON and the selector lever is shifted to the reverse (R), the

beep sound activates and the system is enabled for use.

The sensors detect obstructions under the following conditions:

Sensor

Condition

Rear Ultrasonic Sensor

The selector lever is in reverse (R).

Rear Corner Ultrasonic

The selector lever is in reverse (R), and the vehicle speed is about 10 km/h (6 mph)

Sensor

or less.

▼ Obstruction Detection Indication

The position of a sensor which has detected an obstruction is indicated. The gauge

illuminates in different areas depending on the distance to an obstruction detected by the

sensor.

As the vehicle approaches closer to an obstruction, the zone in the gauge closer to the

vehicle illuminates.

Without 360° view monitor

With 360° view monitor

Front ultrasonic

sensor

Left front corner

Right front

Left front corner

Right front

ultrasonic

corner ultrasonic

ultrasonic

corner ultrasonic

sensor

Left rear corner

Right rear

Left rear corner

Right rear

ultrasonic

corner ultrasonic

ultrasonic

corner ultrasonic

sensor

Rear ultrasonic

sensor

Some models

NOTE

The detection indicator can switch between display and non-display.

Refer to the Settings section in the Mazda Connect Owner's Manual.

(Vehicles with 360° View Monitor)

4-265

When Driving

Parking Sensor System (Mazda Connect (Type A))

When the detection indicator is set to “Display”, even with the 360° view monitor not

displayed, if a front ultrasonic sensor or a front corner ultrasonic sensor detects an

obstruction, the 360° view monitor switches automatically to display. When an obstruction

is no longer detected, the display switches to the display before the obstruction was

detected. However, while the 360° view monitor is displayed, it continues to display no

matter if an obstruction is detected or not.

System problem notification

If a problem occurs, the driver is notified of the problem by the following indications.

Detection Indicator

Without 360° view monitor

Without front ultra-

With 360° view moni-

Solution

With front ultrasonic

sonic sensor and front

sensor and front cor-

tor

corner ultrasonic sen-

ner ultrasonic sensor

sor

The system may have a

malfunction. Have the ve-

Discon-

hicle inspected at an Au-

nection

thorized Mazda Dealer as

soon as possible.

The system may have a

System

malfunction. Have the ve-

mal-

hicle inspected at an Au-

function

thorized Mazda Dealer as

soon as possible.

4-266

When Driving

Parking Sensor System (Mazda Connect (Type A))

Detection Indicator

Without 360° view monitor

Without front ultra-

Solution

With front ultrasonic

With 360° view moni-

sonic sensor and front

sensor and front cor-

tor

corner ultrasonic sen-

ner ultrasonic sensor

sor

Foreign matter may be on

the sensor area corre-

sponding to the obstruc-

Frost/

tion detection indication

soiling

shown. If the system does

not recover, have the vehi-

cle inspected at an Author-

ized Mazda Dealer.

▼ Parking Sensor Warning Beep

The beeper sounds as follows while the system is operating.

Front Ultrasonic Sensor^*, Rear Ultrasonic Sensor

Distance detec-

Distance between vehicle and obstruction

Beeper sound^*1

tion area

Front ultrasonic sensor^*

Rear ultrasonic sensor

Approx. 100―60 cm (39.3―23.6

Approx. 150―60 cm (59.0―23.6

in)

Slow intermittent

Farthest distance

sound

Approx. 60―45 cm (23.6―17.7

in)

Medium intermit-

Far distance

tent sound

*Some models.

4-267

When Driving

Parking Sensor System (Mazda Connect (Type A))

Distance detec-

Distance between vehicle and obstruction

Beeper sound

tion area

Front ultrasonic sensor^*

Rear ultrasonic sensor

Approx. 45―35 cm (17.7―13.7

in)

Fast intermittent

Middle distance

sound

Within approx. 35 cm (13.7 in)

Close distance

Continuous sound

^*1

The rate at which the intermittent sound beeps increases as the vehicle approaches the obstruction.

Front Corner Ultrasonic Sensor^*, Rear Corner Ultrasonic Sensor

Distance between vehicle and obstruction

Distance detection area

Front corner ultrasonic^*/Rear corner ultrasonic

Beeper sound^*1

sensor

Approx. 55―38 cm (21.6―14.9 in)

Far distance

Medium intermittent sound

Approx. 38―25 cm (14.9―9.8 in)

Middle distance

Fast intermittent sound

Within approx. 25 cm (9.8 in)

Close distance

Continuous sound

The rate at which the intermittent sound beeps increases as the vehicle approaches the obstruction.

4-268

*Some models.

When Driving

Parking Sensor System (Mazda Connect (Type A))

NOTE

If an obstruction is detected in a zone for 6 seconds or more, the beep sound is stopped

(except for the close-distance zone). If the same obstruction is detected in another zone, the

corresponding beep sound is heard.

▼ When Warning Indicator/Beep is Activated

The system notifies the driver of an abnormality by activating the beep sound and the

indicator light.

Indicator/Beep

How to check

The indicator light flashes when

the parking sensor switch is

The system may have a malfunction. Have the vehicle inspected at an Author-

pressed at a vehicle speed of 10

ized Mazda Dealer as soon as possible.

km/h (6 mph) or less.

The system may have a malfunction. Have the vehicle inspected at an Author-

The beep sound is not heard.

ized Mazda Dealer as soon as possible.

The intermittent sound of the

Remove any foreign material from the sensor area. If the system does not re-

buzzer is heard 5 times.

cover, have the vehicle inspected at an Authorized Mazda Dealer.

A certain obstruction detection

indicator is continuously dis-

Refer to Obstruction Detection Indication on page 4-265.

played.

4-269

When Driving

Parking Sensor System (Mazda Connect (Type B))

Parking Sensor System (Mazda Connect (Type B))*

The parking sensors use ultrasonic sensors which detect obstructions around the vehicle

when the vehicle is driven at low speeds, such as during garage or parallel parking, and a

buzzer sound and detection indicator notify the driver of the approximate distance from the

vehicle to the surrounding obstruction.

Front corner ultrasonic sensor

Rear ultrasonic

sensor

Rear corner ultrasonic sensor

Front ultrasonic sensor

Some models.

WARNING

Do not rely completely on the parking sensor system and be sure to confirm the safety around

your vehicle visually when driving:

This system can assist the driver in operating the vehicle in the forward and backward

directions while parking. The detection ranges of the sensors are limited, therefore, driving the

vehicle while relying only on the system may cause an accident. Always confirm the safety

around your vehicle visually when driving.

NOTE

^ Do not install any accessories within the detection ranges of the sensors. It may affect the

system operation.

^ Depending on the type of obstruction and the surrounding conditions, the detection range

of a sensor may narrow, or the sensors may not be able to detect obstructions.

^ The system may not operate normally under the following conditions:

^ Mud, ice, or snow is adhering to the sensor area (Returns to normal operation when

removed).

^ The sensor area is frozen (Returns to normal operation when the ice is thawed).

^ The sensor is covered by a hand.

^ The sensor is excessively shocked.

^ The vehicle is excessively tilted.

4-270

*Some models.

When Driving

Parking Sensor System (Mazda Connect (Type B))



Under extremely hot or cold weather conditions.

^ The vehicle is driven on bumps, inclines, gravel, or grass covered roads.

^ Anything which generates ultrasound is near the vehicle, such as another vehicle's

horn, the engine sound of a motorcycle, the air brake sound of a large-sized vehicle, or

another vehicle's sensors.

^ The vehicle is driven in heavy rain or in road conditions causing water-splash.

^ A commercially-available fender pole or an antenna for a radio transmitter is installed

to the vehicle.

^ The vehicle is moving towards a tall or square curbstone.

^ An obstruction is too close to the sensor.

^ Obstructions under the bumper may not be detected. Obstructions that are lower than the

bumper or thin which may have been initially detected may no longer be detected as the

vehicle approaches more closely to the obstruction.

^ The following types of obstructions may not be detected:

^ Thin objects such as wire or rope

^ Things which absorb sonic waves easily such as cotton or snow

^ Angular shaped objects

^ Very tall objects, and those which are wide at the top

^ Small, short objects

^ Always have the system inspected at an Authorized Mazda Dealer if any shock is applied

to the bumpers, even in a minor accident. If the sensors are deviated, they cannot detect

obstructions.

^ The system may have a malfunction if the beep does not operate or the indicator light

does not illuminate when the parking sensor switch is turned on. Consult an Authorized

Mazda Dealer.

^ The system may have a malfunction if the beep sound which indicates a system

malfunction is heard and the indicator light flashes. Consult an Authorized Mazda Dealer.

^ The beeper which indicates a system malfunction may not be heard if the ambient

temperature is extremely cold, or mud, ice, or snow adheres to the sensor area. Remove

any foreign material from the sensor area.

^ When installing a trailer hitch, consult an Authorized Mazda Dealer.

4-271

When Driving

Parking Sensor System (Mazda Connect (Type B))

▼ Sensor Detection Range

The sensors detect obstructions within the following range.

A: About 55 cm (About 21.6 in)

Rear corner ultrasonic sensor detection range

B: About 55 cm (About 21.6 in)

C: About 100 cm (About 39.3 in)

Front ultrasonic sensor detection range

D: About 150 cm (About 59.0 in)

Rear ultrasonic sensor detection range

Front corner ultrasonic sensor detection range

Viewing distance display

Display

Distance between vehicle and obstruction

Front ultrasonic sensor^*/

Rear ultrasonic sensor/

Without 360° view moni-

With 360° view monitor

Front corner ultrasonic

Rear corner ultrasonic

tor

sensor^*

Green

Front ultrasonic sensor:

Rear ultrasonic sensor:

Approx. 100―60 cm

Approx. 150―60 cm

(39.3―23.6 in)

(59.0―23.6 in)

4-272

*Some models.

When Driving

Parking Sensor System (Mazda Connect (Type B))

Display

Distance between vehicle and obstruction

Front ultrasonic sensor^*/

Rear ultrasonic sensor/

Without 360° view moni-

With 360° view monitor

Front corner ultrasonic

Rear corner ultrasonic

tor

sensor^*

Yellow

Front ultrasonic sensor:

Rear ultrasonic sensor:

Approx. 60―45 cm

(23.6―17.7 in)

Front corner ultrasonic sen-

Rear corner ultrasonic sen-

sor:

Approx. 55―38 cm

(21.6―14.9 in)

Amber

Front ultrasonic sensor:

Rear ultrasonic sensor:

Approx. 45―35 cm

(17.7―13.7 in)

Front corner ultrasonic sen-

Rear corner ultrasonic sen-

sor:

Approx. 38―25 cm

(14.9―9.8 in)

Red

Front ultrasonic sensor:

Rear ultrasonic sensor:

Within approx. 35 cm (13.7

in)

Front corner ultrasonic sen-

Rear corner ultrasonic sen-

sor:

Within approx. 25 cm (9.8

in)

▼ Parking Sensor System Operation

The switch can be activated when the ignition is switched ON, the selector lever is in any

position except reverse (R), and the vehicle speed is about 10 km/h (6 mph) or less.

*Some models.

4-273

When Driving

Parking Sensor System (Mazda Connect (Type B))

When the parking sensor switch is pressed, a beep sound is heard, the obstruction detection

indication is displayed in the audio screen, and the indicator light in the switch illuminates.

Indicator light

NOTE

^ If the system is cancelled, it will not restore automatically even when the vehicle speed is

decreased to 10 km/h (6 mph) or less.

^ When the ignition is switched OFF, the system status before it was turned off is

maintained. For example, if the ignition is switched OFF while the parking sensor is

activated, the system will be activated when the ignition is switched ON the next time.

Sensor detection condition

The system can be used when the ignition is switched ON and the parking sensor switch has

been turned on.

The sensors detect obstructions under the following conditions:

Sensor

Condition

The selector lever is in any position except reverse (R), and the vehicle speed is

Front Ultrasonic Sensor

about 10 km/h (6 mph) or less.

Front Corner Ultrasonic

The vehicle speed is about 10 km/h (6 mph) or less.

Sensor

Rear Ultrasonic Sensor

The selector lever is in reverse (R).

Rear Corner Ultrasonic

The selector lever is in reverse (R), and the vehicle speed is about 10 km/h (6 mph)

Sensor

or less.

The system is cancelled under the following conditions:

^ The parking sensor switch is pressed while the parking sensor is in operation.

^ The vehicle speed is 10 km/h (6 mph) or more. (Except rear sensor)

4-274

When Driving

Parking Sensor System (Mazda Connect (Type B))

▼ Obstruction Detection Indication

The position of a sensor which has detected an obstruction is indicated. The gauge

illuminates in different areas depending on the distance to an obstruction detected by the

sensor.

As the vehicle approaches closer to an obstruction, the zone in the gauge closer to the

vehicle illuminates.

Without 360°view monitor

Front sensor ultrasonic gauge

Left front corner

Right front corner

ultrasonic sensor gauge

Left rear corner

Right rear corner

ultrasonic sensor gauge

Rear ultrasonic sensor gauge

With 360°view monitor

Front ultrasonic sensor gauge

Left front corner

Right front corner

ultrasonic sensor gauge

Left rear corner

Right rear corner

ultrasonic sensor gauge

Rear sensor ultrasonic gauge

NOTE

The detection indicator can be switched between display and non-display and the buzzer

volume can be changed.

Refer to the Settings section in the Mazda Connect Owner's Manual.

(Vehicles with 360° View Monitor)

When the detection indicator is set to “Display”, even with the 360° view monitor not

displayed, if a front ultrasonic sensor or a front corner ultrasonic sensor detects an

obstruction, the 360° view monitor switches automatically to display. When an obstruction

is no longer detected, the display switches to the display before the obstruction was

detected. However, while the 360° view monitor is displayed, it continues to display no

matter if an obstruction is detected or not.

4-275

When Driving

Parking Sensor System (Mazda Connect (Type B))

System problem notification

The indication displays if the system has a malfunction.

Without 360°view monitor

With 360°view monitor

Check the reason for the indication displaying on the center display or multi-information

display.

Refer to If a Warning Light Turns On or Flashes on page 7-28.

▼ Parking Sensor Warning Beep

The beeper sounds as follows while the system is operating.

4-276

When Driving

Parking Sensor System (Mazda Connect (Type B))

Front ultrasonic sensor, Rear ultrasonic sensor

Distance Detec-

Distance between vehicle and obstruction

Beeper sound^*1

tion area

Front ultrasonic sensor

Rear ultrasonic sensor

Approx. 100―60 cm (39.3―23.6

Approx. 150―60 cm (59.0―23.6

in)

Slow intermittent

Farthest distance

sound

Approx. 60―45 cm (23.6―17.7

in)

Medium intermit-

Far distance

tent sound

Approx. 45―35 cm (17.7―13.7

in)

Fast intermittent

Middle distance

sound

Within approx. 35 cm (13.7 in)

Close distance

Continuous sound

The rate at which the intermittent sound beeps increases as the vehicle approaches the obstruction.

Front corner ultrasonic sensor, Rear corner ultrasonic sensor

Distance between vehicle and obstruction

Distance Detection area

Front corner ultrasonic sensor/Rear corner ultra-

Beeper sound^*1

sonic sensor

Approx. 55―38 cm (21.6―14.9 in)

Far distance

Medium intermittent sound

4-277

When Driving

Parking Sensor System (Mazda Connect (Type B))

Distance between vehicle and obstruction

Distance Detection area

Front corner ultrasonic sensor/Rear corner ultra-

Beeper sound^*1

sonic sensor

Approx. 38―25 cm (14.9―9.8 in)

Middle distance

Fast intermittent sound

Within approx. 25 cm (9.8 in)

Close distance

Continuous sound

The rate at which the intermittent sound beeps increases as the vehicle approaches the obstruction.

NOTE

^ If an obstruction is detected in a zone for 6 seconds or more, the beep sound is stopped

(except for the close-distance zone). If the same obstruction is detected in another zone,

the corresponding beep sound is heard.

▼ When Warning Indicator/Beep is Activated

The system notifies the driver of an abnormality by activating the beep sound and the

indicator light.

Indicator/Beep

How to check

The indicator light flashes when

the parking sensor switch is

The system may have a malfunction. Have the vehicle inspected at an Author-

pressed at a vehicle speed of 10

ized Mazda Dealer as soon as possible.

km/h (6 mph) or less.

The system may have a malfunction. Have the vehicle inspected at an Author-

The beep sound is not heard.

ized Mazda Dealer as soon as possible.

The intermittent sound of the

Remove any foreign material from the sensor area. If the system does not re-

buzzer is heard 5 times.

cover, have the vehicle inspected at an Authorized Mazda Dealer.

A certain obstruction detection

indicator is continuously dis-

Refer to Obstruction Detection Indication on page 4-265.

played.

4-278

Interior Features

Use of various features for ride comfort, including air-conditioning

system and audio system.

Climate Control System

5-2

Mazda Connect Basic

Operating Tips

5-2

Operations

5-37

Vent Operation (Front)

5-3

Connected Service (If

Front Air Conditioner

5-5

applicable)

5-53

Vent Operation (Rear)

5-9

Rear Air Conditioner

5-11

Interior Equipment

5-55

Sunvisors

5-55

Mazda Connect [Mazda Connect

Interior Lights

5-56

(Type A)]

5-14

Accessory Sockets

5-60

What is Mazda Connect ?

5-14

USB Power Outlet*

5-61

Mazda Connect Basic

Wireless Charger (Qi)*

5-64

Operations

5-17

Cup Holder

5-67

Bottle Holder

5-69

Mazda Connect [Mazda Connect

Storage Compartments

5-69

(Type B)]

5-33

Sunshade (Rear Door Window)*

What is Mazda Connect ?

5-33

. . . . . . . . . . . . . 5-75

*Some models.

5-1

Interior Features

Climate Control System

because a special device is required for

Operating Tips

the air conditioner maintenance.

^ Operate the climate control system with

For details, consult an Authorized

the engine running.

Mazda Dealer.

^ To prevent the battery from being

discharged, do not leave the fan control

Label

switch on for a long period of time with

the ignition switched ON when the

engine is not running.

^ Clear all obstructions such as leaves,

snow and ice from the hood and the air

inlet in the cowl grille to improve the

system efficiency.

^ Use the climate control system to defog

the windows and dehumidify the air.

^ The recirculate mode should be used

when driving through tunnels or while

in a traffic jam, or when you would like

to shut off outside air for quick cooling

of the interior.

^ Use the outside air position for

ventilation or windshield defrosting.

^ If the vehicle has been parked in direct

sunlight during hot weather, open the

windows to let warm air escape, then

run the climate control system.

^ Run the air conditioner about 10

minutes at least once a month to keep

internal parts lubricated.

^ Have the air conditioner checked before

the weather gets hot. Lack of refrigerant

may make the air conditioner less

efficient.

The refrigerant specifications are

indicated on a label attached to the

inside of the engine compartment. If the

wrong type of refrigerant is used, it

could result in a serious malfunction of

the air conditioner. Consult a

professional, government certified

repairer for the inspection or repair

5-2

Interior Features

Climate Control System

Side Vents

Vent Operation (Front)

knob

▼ Adjusting the Vents

Directing airflow

To adjust the direction of airflow, move

the adjustment knob.

close open

NOTE

Center Vents

^ When using the air conditioner under

humid ambient temperature conditions,

Knob

the system may blow fog from the vents.

This is not a sign of trouble but a result

of humid air being suddenly cooled.

^ The air vents can be fully opened and

closed by operating the dial. (Side vents

only)

5-3

Interior Features

Climate Control System

▼ Selecting the Airflow Mode

Dashboard Vents

Defroster and Floor Vents

Dashboard and Floor Vents

Defroster Vents

Floor Vents

NOTE

The location airflow exits the air vents and the airflow amount may change depending on

the open or close status of the air vents.

5-4

Interior Features

Climate Control System

Front Air Conditioner

Climate control system information is displayed on the display.

Windshield defroster switch

SYNC (synchronized

Air intake selector

Rear window

AUTO switch

temperature) switch

defogger switch

Power switch

A/C switch

Driver temperature

Fan control

Mode selector

Passenger temperature

control dial

switch

control dial

▼ Control Switches

The functions for switches other than

those operated continue to operate in

AUTO switch

auto control.

By pressing the AUTO switch the

Power switch (Fan On/Off)

following functions will be automatically

controlled in accordance with the selected

The climate control system turns on or off

set temperature:

by pressing the power switch.

^ Airflow temperature

Temperature control dial

^ Amount of airflow

This dial controls temperature. Turn it

^ Selection of airflow mode

clockwise for hot and counterclockwise

^ Outside/Recirculated air selection

for cold.

^ Air conditioner operation

Turn the temperature control dial to adjust

the temperature between 15 °C (60 °F) and

NOTE

29 °C (84 °F).

AUTO switch indicator light

^ When the SYNC switch is on:

^ When on, it indicates auto operation,

Turn the driver temperature control dial

and the system will function

to control the temperature throughout

automatically.

the entire cabin.

^ If any of the following switches are

^ When the SYNC switch is off:

operated while in auto control, the

Turn the driver or front passenger

AUTO switch indicator turns off.

temperature control dial to

^ Mode selector switch

independently control the temperature

^ Fan control switch

on each side of the cabin.

^ Windshield defroster switch

5-5

Interior Features

Climate Control System

NOTE

^ To set the air vent to

, press the

windshield defroster switch.

^ The climate control system changes to

^ In the

position, the air

the individual operation mode (SYNC

conditioner is automatically turned on

switch indicator light turns off) by

and the outside air position is

turning the front passenger temperature

automatically selected to defrost the

control dial even when the SYNC switch

windshield. In the or

position, the

is on, which allows individual control of

outside air position cannot be changed

the set temperature for the driver and

to the recirculated air position.

front passenger.

^ When you set the temperature to the

A/C switch

lower or upper limit, “Lo” or “Hi” is

Pressing the A/C switch while the AUTO

displayed.

switch is turned on will turn off the air

^ The temperature units for the

conditioner (cooling/dehumidifying

temperature setting display can be

functions).

changed in conjunction with the

The on/off of the air conditioner switches

temperature units for the outside

each time the A/C switch is pressed.

temperature display.

(Instrument cluster Type A)

NOTE

Refer to Outside Temperature Display

^ The air conditioner operates when the

on page 4-18.

A/C switch is pressed while the air

(Instrument cluster Type B)

conditioner is turned off.

Refer to Outside Temperature Display

^ The air conditioner may not function

on page 4-35.

when the outside temperature

Fan control switch

approaches 0 °C (32 °F).

The fan has 7 speeds. The selected speed

Air intake selector

will be displayed.

Outside or recirculated air positions can be

Mode selector switch

selected. Press the switch to select outside/

recirculated air positions.

The desired airflow mode can be selected

(page 5-4).

Recirculated air position (indicator light

turns on)

NOTE

Outside air is shut off. Air within the

^ With the airflow mode set to the

vehicle is recirculated. Use this position

position and the temperature control

when going through tunnels, driving in

dial set at a medium temperature,

congested traffic (high engine exhaust

heated air is directed to the feet and air

areas), or when quick cooling is desired.

at a comparably lower temperature will

flow through the central, left and right

vents.

5-6

Interior Features

Climate Control System

Outside air position (indicator light

Interconnection mode (indicator light

turns off)

turns on)

Outside air is allowed to enter the cabin.

The set temperature for the driver and

Use this position for ventilation or

front passenger is controlled

windshield defrosting.

simultaneously.

Individual operation mode (indicator

WARNING

light turns off)

The set temperature can be controlled

Do not recirculate the air in the cabin

individually for the driver and front

during cold or rainy weather:

passenger.

Recirculating the air in the cabin during

cold and rainy weather is dangerous as it

Windshield defroster switch

will cause the windows to fog up. Your

Press the switch to defrost the windshield

vision will be hampered, which could lead

and front door windows.

to a serious accident.

Refer to Windshield Defrosting and

Defogging on page 5-8.

NOTE

Rear window defogger switch

^ The recirculated air position is the

default position whenever the ignition is

Press the rear window defogger switch to

switched ON, the climate control system

defrost the rear window.

is on, and the outside temperature

Refer to Rear Window Defogger on page

exceeds about 73°F (23౯).

4-70.

^ To exit the default recirculated air

▼ Operation of Automatic Air

position, press the air intake selector

Conditioner

switch to select the outside air position.

^ When the air intake selector switch is set

1. Press the AUTO switch. Selection of

to the outside air position and the

the airflow mode, air intake selector

outside temperature exceeds about 73°F

and amount of airflow will be

(23౯), the climate control system may

automatically controlled.

automatically select the recirculated air

2. Use the temperature control dial to

position to improve the efficiency of the

select a desired temperature.

climate control system.

If you want to set the temperature on

the front passenger's side separately

SYNC (Synchronized Temperature)

from the driver's side, turn the front

switch

passenger temperature control dial to

Use the SYNC switch to change the mode

switch the mode automatically to the

between the individual operation (driver

individual operation mode and set the

and passenger) and interconnection

temperature for the front passenger's

(simultaneous) modes.

side.

5-7

Interior Features

Climate Control System

To turn off the system, press the power

NOTE

switch.

Use the temperature control dial to

increase the air flow temperature and

NOTE

defog the windshield more quickly.

^ Set the control dial to the recommended

▼ Sunlight/Interior Temperature

temperature of 22 °C (72 °F), and then

Sensor

adjust it as desired.

^ Setting the temperature to maximum hot

Sunlight sensor

or cold will not provide the desired

Do not place objects on the sunlight

temperature at a faster rate.

sensor. Otherwise, the interior temperature

^ When selecting heat, the system will

may not adjust correctly.

restrict airflow until the engine has

warmed to prevent cold air from

Sunlight sensor

blowing out of the vents.

▼ Windshield Defrosting and

Defogging

Press the windshield defroster switch.

In this position, the outside air position is

automatically selected, and the air

conditioner automatically turns on. The air

conditioner will directly dehumidify the

air to the front windshield and side

windows on page 5-4.

Interior temperature sensor

Airflow amount will be increased.

Do not cover the interior temperature

sensor. Otherwise, the interior temperature

WARNING

may not adjust correctly.

Set the temperature control to the hot or

warm position when defogging (

position):

Using the position with the temperature

control set to the cold position is

dangerous as it will cause the outside of the

windshield to fog up. Your vision will be

hampered, which could lead to a serious

accident.

Interior temperature sensor

5-8

Interior Features

Climate Control System

Vent Operation (Rear)

▼ Adjusting the Vents

Directing airflow

You can direct air flow by moving the adjustment knob.

NOTE

When using the air conditioner, mist may come out from the vents. This is not a sign of

trouble but a result of humid air being suddenly cooled.

knob

5-9

Interior Features

Climate Control System

▼ Selecting the Airflow Mode

Dashboard Vents

Floor Vents

Dashboard and Floor Vents

5-10

Interior Features

Climate Control System

Rear Air Conditioner

Climate control system information is displayed on the display.

REAR switch

AUTO

SYNC

Mode selector display

Airflow display

Temperature setting display

Power switch

AUTO switch

Fan control switch

Mode selector switch

Temperature control

switch

▼ Control Switches

Power switch

Rear switch

The rear climate control system turns on

or off by pressing the power switch.

Press the rear switch to operate the rear air

conditioner.

Temperature control switch

The indicator illuminates to indicate that

This switch controls temperature. Press

the rear air conditioner is operating.

for hot and for cold.

AUTO switch

Operate the temperature control switch to

adjust the temperature between 15 °C

By pressing the AUTO switch the

(60 °F) and 29 °C (84 °F).

following functions will be automatically

controlled in accordance with the set

NOTE

temperature:

When the temperature control switch is set

to the maximum or minimum, “Hi” or

^ Airflow temperature

“Lo” is indicated on the display.

^ Amount of airflow

^ Selection of airflow mode

5-11

Interior Features

Climate Control System

Fan control switch

^ When the rear air conditioner is

controlled to the same temperature

The fan has five speeds. The selected

setting as the front air conditioner

speed will be displayed.

for the driver's side, “SYNC” is

Mode selector switch

displayed on the rear screen.

^ When operating the fan switch of the

The desired airflow mode can be selected.

front air conditioner while the rear

Refer to Selecting the Airflow Mode on

air conditioner is operating

page 5-10.

automatically, the airflow amount of

▼ Operation of Automatic Air

the rear air conditioner may change.

Conditioner

Operation from rear seats

Operation from front seats

Turn the front air conditioner on.

Press the AUTO switch. The selection

Press the rear switch. The rear air

of the airflow mode and airflow

conditioner operates.

amount will be automatically

Selection of the airflow mode, airflow

controlled.

amount and temperature will be

Use the temperature control switch to

automatically controlled to the same

set the desired temperature.

temperature setting as the front air

NOTE

conditioner for the driver's side.

^ Set the control switch to the

NOTE

recommended temperature of 22 °C

^ Set the control dial to the

(72 °F), and then adjust it as

recommended temperature of 22 °C

desired.

(72 °F), and then adjust it as

^ If the AUTO switch is pressed while

desired.

the front A/C switch is off, the rear

^ If the AUTO switch is pressed while

air conditioner operates only to

the front A/C switch is off, the rear

circulate air.

air conditioner operates only to

^ Setting the temperature to the

circulate air.

maximum high or low will not

^ Setting the temperature to the

provide the desired temperature at a

maximum high or low will not

faster rate.

provide the desired temperature at a

^ When selecting heat, the system will

faster rate.

restrict airflow until it has warmed

^ When selecting heat, the system will

to prevent cold air from blowing out

restrict airflow until it has warmed

of the vents.

to prevent cold air from blowing out

^ When the rear air conditioner is

of the vents.

operated automatically, “AUTO” is

displayed on the rear screen.

5-12

Interior Features

Climate Control System



When the rear air conditioner is

controlled to the same temperature

setting as the front air conditioner

for the driver's side, “SYNC” is

displayed on the rear screen.

To turn off the system, press the Power

switch.

5-13

Была ли эта страница вам полезна?

Да!Нет

1 посетитель считают эту страницу полезной.

Mazda CX-9 (2022 year). Manual in english — page 14

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.