Mazda CX 7. Manual — part 399
SECURITY AND LOCKS
09-14–31
09-14
1D
keyless
antenna
(exterior, RF)(-)
keyless antenna
(exterior, RF)
Under any condition: Inspect
for continuity to keyless
antenna.
Continuity
detected
keyless antenna (exterior, RF)
1E
keyless
antenna
(exterior,
rear)(+)
keyless antenna
(exterior, rear)
Under any condition: Inspect
for continuity to keyless
antenna.
Continuity
detected
keyless antenna (exterior, rear)
1F
keyless
antenna
(exterior,
rear)(-)
keyless antenna
(exterior, rear)
Under any condition: Inspect
for continuity to keyless
antenna.
Continuity
detected
keyless antenna (exterior, rear)
1G
GND
Body ground
Under any condition: Inspect
for continuity to ground.
Continuity
detected
GND
1H
GND
Body ground
Under any condition: Inspect
for continuity to ground.
Continuity
detected
GND
1I
keyless
antenna
(interior,
rear)(+)
keyless antenna
(interior, rear)
Under any condition: Inspect
for continuity to keyless
antenna.
Continuity
detected
keyless antenna (interior, rear)
1J
keyless
antenna
(interior, rear)(-
)
keyless antenna
(interior, rear)
Under any condition: Inspect
for continuity to keyless
antenna.
Continuity
detected
keyless antenna (interior, rear)
1M
keyless
antenna
(interior,
middle)(+)
keyless antenna
(interior, middle)
Under any condition: Inspect
for continuity to keyless
antenna.
Continuity
detected
keyless antenna (interior,
middle)
1N
keyless
antenna
(interior,
middle)(-)
keyless antenna
(interior, middle)
Under any condition: Inspect
for continuity to keyless
antenna.
Continuity
detected
keyless antenna (interior,
middle)
1O
keyless
antenna
(interior,
front)(+)
keyless antenna
(interior, front)
Under any condition: Inspect
for continuity to keyless
antenna.
Continuity
detected
keyless antenna (interior, front)
1P
keyless
antenna
(interior,
front)(-)
keyless antenna
(interior, front)
Under any condition: Inspect
for continuity to keyless
antenna.
Continuity
detected
keyless antenna (interior, front)
2A
Power supply
ROOM 15 A fuse
Under any condition
B+
ROOM 15 A FUSE
2B
GND
Body ground
Under any condition: Inspect
for continuity to ground.
Continuity
detected
GND
2C
IG1
IG1 10 A fuse
Ignition switch is at ON
position
B+
IG1 10 A fuse
Ignition switch is at LOCK or
ACC position
1.0 or less
2E
ACC
METER 7.5 A
fuse
Ignition switch is at ACC
position
B+
METER 7.5 A fuse
Ignition switch is at LOCK or
ON position
1.0 or less
2K
Beeper
Keyless beeper
Beeper operated
1.0 or less
Keyless beeper
Other
5.0
3A
Power supply
(keyless
receiver)
Keyless receiver
Under any condition
B+
Keyless receiver
3C
Communicatio
n (keyless
receiver)
Keyless receiver
Under any condition: Inspect
for continuity to keyless
receiver.
Continuity
detected
Keyless receiver
3E
Start knob
(push switch)
Steering lock unit
Start knob is Pushed
B+
Steering lock unit
Other
1.0 or less
Terminal
Signal name
Connected to
Measured condition
Voltage (V)/
Continuity
Inspection item(s)
SECURITY AND LOCKS
09-14–32
End Of Sie
KEYLESS CONTROL MODULE CONFIGURATION[ADVANCED KEYLESS SYSTEM]
id0914008068b1
1. Connect the M-MDS to the DLC-2 connector.
2. After the vehicle is identified, select the following
items from the initialization screen of the M-MDS.
• When using the IDS (notebook PC)
1. Select “Module Programming”.
• When using the PDS (pocket PC)
1. Select “Programming”.
2. Select “Module Programming”.
3. Then, select items from the screen menu in the
following order.
1. Select “Programmable Module Installation”.
2. Select “RKE”.
4. Perform the configuration according to the
directions on the screen.
End Of Sie
WM: KEYLESS ENTRY SYSTEM
3F
Key reminder
switch
Steering lock unit
Key reminder switch is ON
B+
Steering lock unit
Other
1.0 or less
3H
Communicatio
n (steering lock
unit)
Steering lock unit
Under any condition: Inspect
for continuity to steering lock
unit.
Continuity
detected
Steering lock unit
3E
Request switch
input
(passenger-
side)
Request switch
input (passenger-
side)
Passenger-side request
switch is ON: Inspect for
continuity to ground.
Continuity
detected
Request switch input
(passenger-side)
Passenger-side request
switch is OFF: Inspect for
continuity to ground.
No continuity
3K
Request switch
input (driver-
side)
Request switch
input (driver-side)
Driver-side request switch is
ON: Inspect for continuity to
ground.
Continuity
detected
Request switch input (driver-
side)
Driver-side request switch is
OFF: Inspect for continuity
to ground.
No continuity
3M
Request switch
input (liftgate)
Request switch
input (liftgate)
Liftgate request switch is
ON: Inspect for continuity to
ground.
Continuity
detected
Request switch input (liftgate)
Liftgate request switch is
OFF: Inspect for continuity
to ground.
No continuity
3N
Lock signal
input
Door lock-link
switch
Driver-side door is locked:
Inspect for continuity to
ground.
No continuity
Door lock-link switch
Driver-side door is unlocked:
Inspect for continuity to
ground.
Continuity
detected
3Q
Communicatio
n (BCM)
BCM
Under any condition: Inspect
for continuity to BCM.
Continuity
detected
BCM
3U
Tx-SKE
Coil antenna
Ignition switch is at ON
position
B+
Coil antenna
Ignition switch is at LOCK or
ACC position
1.0 or less
3V
Rx-SKE
Coil antenna
Ignition switch is at ON
position
B+
Coil antenna
Ignition switch is at LOCK or
ACC position
1.0 or less
3W
HS-CAN+
PCM
Under any condition: Inspect
for continuity to PCM.
Continuity
detected
-
3X
HS-CAN-
PCM
Under any condition: Inspect
for continuity to PCM.
Continuity
detected
-
Terminal
Signal name
Connected to
Measured condition
Voltage (V)/
Continuity
Inspection item(s)
DLC-2
acxuuw00002506
SECURITY AND LOCKS
09-14–33
09-14
CARD KEY ID CODE REGISTRATION[ADVANCED KEYLESS SYSTEM]
id0914008071b1
Caution
• Do not place the following devices in the vehicle while programming, otherwise programming
cannot be performed.
— M-MDS
— Personal computer
— Device that can send/receive radio waves
• Verify that the other transmitter is not being operated around the servicing area during card key
programming.
Note
• Use the M-MDS and start programming if the condition corresponds to the following:
— One or No Programmed Card Keys
— Keyless control module is replaced
• If six card keys are already programmed, the programming mode does not activate. If programming is
needed, use the M-MDS to erase the unnecessary card key programming.
With two programmed card keys
1. Bring the programmed card keys (2) and a unprogrammed card key into the vehicle.
2. Close all doors.
3. Insert the supplementary key into the ignition key cylinder.
Note
• Complete the procedures up to Step 7 within 30 s after the supplementary key is inserted.
4. Turn the ignition switch to the ON position.
5. Press the UNLOCK button on card key 1.
6. Press the UNLOCK button on card key 2.
7. From the ignition switch in the ON position, switch the ignition switch in the order indicated below.
— ACC
→ON→ACC→ON→ACC→ON
8. Open the driver-side front door, press the door switch twice, and then close the door.
Note
• After Step 3 is completed and the card key programming mode is activated, the door lock actuator
operates to lock, and then operates to unlock.
• If the door lock actuator does not operate, repeat the procedure from Step 2.
9. Press the UNLOCK button on the unprogrammed card key twice.
Note
• After Step 8 is completed and the card key is programmed, the door lock actuator operates to lock, and
then operates to unlock.
10. If programming more card keys, remove the supplementary key once, and then repeat the procedure from Step
2.
Using M-MDS
1. Fully lower the driver-side door glass.
2. Connect the M-MDS to the DLC-2.
3. Pull out the M-MDS cable from the door glass
opening and set the M-MDS outside the vehicle.
Caution
• Protect the cable and body contact area
with a clean rag, otherwise they could be
damaged.
DLC-2
acxuuw00002508
SECURITY AND LOCKS
09-14–34
4. After the vehicle is identified, select the following items from the initialization screen of the M-MDS.
• When using the IDS (notebook PC)
1. Select “Body”.
2. Select “Security”.
• When using the PDS (pocket PC)
1. Select “Programming”.
5. Then, select items from the screen menu in the following order.
1. Select “PATS functions”.
2. Select “Program Additional Card Key”.
6. Security access begins and the M-MDS displays the “OUT-CODE“.
Note
• When “OUT-CODE“ is first displayed, turning the ignition switch from the LOCK to the ON position 5 times
will change the “OUT-CODE”.
7. Input the “IN-CODE“ that corresponds to the “OUT-CODE “ displayed on the M-MDS screen.
8. Select “CARD KEY PROGRAMMING“ from the M-MDS screen menu.
Note
• After Step 8 is completed and the card key programming is activated, the door lock actuator operates to
lock, and then operates to unlock.
9. Press the unprogrammed card key UNLOCK button twice.
Note
• After Step 9 is completed and the card key is programmed, the door lock actuator operates to lock, and
then operates to unlock.
10. If programming more card keys, remove the supplementary key once, and then repeat the procedure from Step
7 by following the instructions on the M-MDS screen.
End Of Sie
CLEARING CARD KEY[ADVANCED KEYLESS SYSTEM]
id0914008072b1
1. Fully lower the driver-side door glass.
2. Connect the M-MDS to the DLC-2.
3. Pull out the M-MDS cable from the door glass
opening and set the M-MDS outside the vehicle.
Caution
• Protect the cable and body contact area
with a clean rag, otherwise they could be
damaged.
4. After the vehicle is identified, select the following
items from the initialization screen of the M-MDS.
• When using the IDS (notebook PC)
1. Select “Body”.
2. Select “Security”.
• When using the PDS (pocket PC)
1. Select “Programming”.
5. Then, select items from the screen menu in the following order.
1. Select “PATS functions”.
2. Select “Card Key Code Erase”.
6. Security access begins and the M-MDS displays the “OUT-CODE“.
Note
• When “OUT-CODE“ is first displayed, turning the ignition switch from the LOCK to the ON position 5 times
will change the “OUT-CODE”.
7. Input the “IN-CODE“ that corresponds to the “OUT-CODE“ displayed in the M-MDS screen.
8. Select “CARD KEY CLEARING“ from the M-MDS screen menu.
End Of Sie
DLC-2
acxuuw00002509
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст