Mazda CX 7. Manual — part 216
PARKING BRAKE SYSTEM
04-12–9
04-12
8. Inspect the rear wheel alignment. (See 02-11-4 REAR WHEEL ALIGNMENT.)
.
11
13
16
15
18
19
20
14
17
21
24
23
22
7
2
10
8
H
H
D
78.4—101.9
{8.0—10.3, 57.9—75.1}
18.6—25.5
{1.90—2.60,
13.8—18.8}
18.6—25.5
{1.90—2.60, 13.8—18.8}
18.6—25.5
{1.90—2.60,
13.8—18.8}
18.6—25.5
{1.90—2.60,
13.8—18.8}
98—120
{10—12, 73—88}
A
B
E
E
C
F
G
A
B
4
3
1
6
C
N·m {kgf·m, ft·lbf}
9.8—14.7
N·m
{100—149 kgf·cm,
87—130 in·lbf}
12
3—6
N·m
{40—60 kgf·cm,
30—50 in·lbf}
3—6
N·m
{40—60 kgf·cm,
30—50 in·lbf}
7.8—10.8
N·m
{80—110 kgf·cm,
70—95 in·lbf}
9
5
G
D
F
18.6—25.5
{1.90—2.60,
13.8—18.8}
20
acxuuw00001873
1
Parking brake switch connector
2
Adjusting nut
3
Parking brake switch
4
Parking brake pedal
5
Spring
6
Clip
7
End cable
(See 04-12-10 End Cable Removal Note.)
(See 04-12-13 End Cable Installation Note.)
8
Rear parking brake cable
9
Front Parking brake cable, equalizer
10
Brake caliper component
(See 04-12-10 Brake Caliper Component Removal
Note)
11
Plug
12
Screw
(See 04-12-12 Disc Plate, Screw Installation Note)
13
Disc plate
(See 04-12-10 Disc Plate Removal Note)
(See 04-12-12 Disc Plate, Screw Installation Note)
14
Spring
15
Parking brake shoe
(See 04-12-11 Parking Brake Shoe Removal Note)
(See 04-12-11 Parking Brake Shoe Installation
Note)
16
Rear wheel hub component
17
Shoe stopper
18
Backing plate
19
Parking brake plate
20
Adjuster bolt and nut, tappet
(See 04-12-11 Operation lever, Pin, Adjuster Bolt
and Nut, Tappet Installation Note)
21
Pin
(See 04-12-11 Operation lever, Pin, Adjuster Bolt
and Nut, Tappet Installation Note.)
22
Operation lever
(See 04-12-11 Operation lever, Pin, Adjuster Bolt
and Nut, Tappet Installation Note.)
23
Plate
24
Dust boot
1871-1U-06B(04-12).fm 9 ページ 2006年3月15日 水曜日 午前11時15分
PARKING BRAKE SYSTEM
04-12–10
End Cable Removal Note
1. Remove the end cable installation bolts.
2. Disconnect the end cable from the operation lever.
3. Bend the end cable tab (rear parking brake cable
side) in the direction shown in the figure.
4. Move the rear parking brake cable end in the
direction shown in the figure and disconnect it
from the end cable.
5. Remove the end cable.
Brake Caliper Component Removal Note
1. Remove the brake caliper assembly from the trailing link and suspend it with a cable so it does not interfere.
Disc Plate Removal Note
1. If any disc plate is difficult to remove, perform the following steps to remove it.
(1) Insert a flathead screwdriver into the service
hole and turn the adjuster in the direction of
the arrow to compress the parking brake
shoe.
(2) Remove the disc plate.
1
2
END CABLE
REAR PARKING BRAKE CABLE
TAB
acxuuw00001902
LEFT SIDE
RIGHT SIDE
acxuuw00001050
1871-1U-06B(04-12).fm 10 ページ 2006年3月15日 水曜日 午前11時15分
PARKING BRAKE SYSTEM
04-12–11
04-12
Parking Brake Shoe Removal Note
1. Pull the parking brake shoe downward and
disengage it from the shoe stopper.
2. Press the adjuster bolt and tappet by hand, and
slowly remove the parking brake shoe.
Note
• When removing the parking brake shoe,
firmly press the adjuster bolt and tappet by
hand and slowly remove the parking brake
shoe to prevent the adjuster bolt, tappet,
operation lever and other parts from flying
off.
Operation lever, Pin, Adjuster Bolt and Nut, Tappet Installation Note
1. Install the operation lever, pin, adjuster bolt and
nut, and tappet so that the adjuster nut is facing
toward the vehicle front.
2. Completely tighten the adjuster bolt and nut.
3. Move the operation lever by hand and verify that it
operates properly.
• If proper operation cannot be verified,
reinstall.
Parking Brake Shoe Installation Note
1. Measure the parking brake lining thickness with a
vernier caliper or measuring scale.
• If it is less than the minimum thickness, install
a new parking brake shoe.
Minimum parking brake shoe thickness
1.0 mm {0.04 in}
2. After installing the opening of the parking brake
shoe to the adjuster bolt and tappet, push the
brake shoe upward and attach it to the shoe
stopper.
SHOE STOPPER
PARKING BRAKE SHOE
acxuuw00001051
TAPPET
PIN
FRONT
OPERATION LEVER
ADJUSTER BOLT
ADJUSTER NUT
acxuuw00001052
acxuuw00001053
SHOE STOPPER
PARKING BRAKE SHOE
BACKING
PLATE
SHOE STOPPER
PARKING BRAKE SHOE
acxuuw00001054
1871-1U-06B(04-12).fm 11 ページ 2006年3月15日 水曜日 午前11時15分
PARKING BRAKE SYSTEM
04-12–12
Disc Plate, Screw Installation Note
1. Measure the inner diameter of the disc plate with
a vernier caliper.
• If it exceeds the maximum diameter, install
the new disc plate.
Maximum rear disc plate inner diameter
191.0 mm {7.52 in}
2. Install the disc plate and screw.
3. Perform the following steps to adjust the shoe
clearance after installing the disc plate and the
screws.
(1) Insert a flathead screwdriver into the service
hole and turn the adjuster in the direction of
the arrow to expand the parking brake shoe
until the disc plate cannot rotate.
(2) Return the adjuster 13—17 notches in the
direction of the arrow.
Note
• Shoe clearance can be adjusted to 0.15 mm
{0.006 in} by returning the adjuster 15
notches.
(3) Rotate the disc plate and make sure it does
not drag.
acxuuw00001055
LEFT SIDE
RIGHT SIDE
acxuuw00001056
LEFT SIDE
RIGHT SIDE
acxuuw00001057
1871-1U-06B(04-12).fm 12 ページ 2006年3月15日 水曜日 午前11時15分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст