Mazda CX 7. Manual — part 415
INTERIOR TRIM
09-17–25
09-17
SUB TRUNK BOX REMOVAL/INSTALLATION
id091700805200
1. Remove the screws.
2. Remove the sub trunk box.
3. Install in the reverse order of removal.
End Of Sie
WM: LIFTGATE TRIM
LIFTGATE UPPER TRIM REMOVAL/INSTALLATION
id091700803600
1. Pull the liftgate upper trim and detach clips A and
B, pin C.
2. Remove the liftgate upper trim.
3. Install in the reverse order of removal.
End Of Sie
LIFTGATE SIDE TRIM REMOVAL/INSTALLATION
id091700803700
1. Remove the liftgate upper trim. (See 09-17-25 LIFTGATE UPPER TRIM REMOVAL/INSTALLATION.)
2. Remove the fastener.
3. Pull the liftgate side trim toward you, then
disengage the clip A and pin B from the body.
4. Remove the tab C, E and clip D.
5. Remove the liftgate side trim.
6. Install in the reverse order of removal.
End Of Sie
SCREW
SCREW
SCREW
LH
RH
SCREW
acxuuw00000921
A
A
CLIP A
CLIP B
PIN C
B
B
C
acxuuw00000868
CLIP A
CLIP D
TAB E
TAB C
FASTENER
LIFTGATE
LOWER
TRIM
LIFTGATE LOWER
TRIM
PIN B
A
A
B
C D
E
acxuuw00000869
INTERIOR TRIM
09-17–26
LIFTGATE LOWER TRIM REMOVAL/INSTALLATION
id091700803800
1. Remove the liftgate upper trim. (See 09-17-25 LIFTGATE UPPER TRIM REMOVAL/INSTALLATION)
2. Remove the liftgate side trim. (See 09-17-25 LIFTGATE SIDE TRIM REMOVAL/INSTALLATION)
3. Pull the recess toward you, then remove it.
4. Remove the fasteners.
5. Pull the liftgate lower trim toward you, then
disengage the clips A, B and pins C from the
body.
6. Remove the liftgate lower trim.
7. Install in the reverse order of removal.
End Of Sie
WM: HEADLINER
SUNVISOR REMOVAL/INSTALLATION
id091700801700
1. Remove the screw, then the sunvisor.
A
A
B
B
TAB A
RECESS
TAB B
acxuuw00000870
FASTENER
A
A
A
A
A
A
A
A
B
B
C
C
C
CLIP B
CLIP A
PIN C
acxuuw00000871
SCREW
SUNVISOR
acxuuw00000674
INTERIOR TRIM
09-17–27
09-17
2. Disengage the center adapter (sunvisor stopper)
from the body using a fastener remover.
3. Install in the reverse order of removal.
End Of Sie
ASSIST HANDLE REMOVAL/INSTALLATION
id091700801800
1. Insert a screwdriver into the assist handle notch
and remove the assist handle cover.
2. Pull the assist handle outward, then remove the
assist handle.
3. Install in the reverse order of removal.
End Of Sie
HEADLINER REMOVAL/INSTALLATION
id091700801600
1. Disconnect the negative battery cable.
2. Partially peel back the seaming welt.
3. Remove the following parts:
(1) A-pillar lower trim (See 09-17-16 A-PILLAR LOWER TRIM REMOVAL/INSTALLATION.)
(2) A-pillar trim (See 09-17-15 A-PILLAR TRIM REMOVAL/INSTALLATION.)
(3) Front scuff plate inner (See 09-17-19 FRONT SCUFF PLATE REMOVAL/INSTALLATION.)
(4) Rear scuff plate inner (See 09-17-19 REAR SCUFF PLATE REMOVAL/INSTALLATION.)
(5) B-pillar lower trim (See 09-17-16 B-PILLAR LOWER TRIM REMOVAL/INSTALLATION.)
(6) Front seat belt upper anchor installation bolt (See 08-11-2 FRONT SEAT BELT REMOVAL/
INSTALLATION.)
(7) B-pillar upper trim (See 09-17-16 B-PILLAR UPPER TRIM REMOVAL/INSTALLATION.)
(8) Rear seat (See 09-13-7 REAR SEAT REMOVAL/INSTALLATION.)
(9) Sub trunk box (See 09-17-25 SUB TRUNK BOX REMOVAL/INSTALLATION.)
(10)Trunk end trim (See 09-17-24 TRUNK END TRIM REMOVAL/INSTALLATION.)
(11)Trunk side trim (See 09-17-24 TRUNK SIDE TRIM REMOVAL/INSTALLATION.)
(12)C-pillar trim (See 09-17-17 C-PILLAR TRIM REMOVAL/INSTALLATION.)
(13)D-pillar trim (See 09-17-18 D-PILLAR TRIM REMOVAL/INSTALLATION.)
(14)Map light (See 09-18-22 MAP LIGHT REMOVAL/INSTALLATION.)
(15)Sunvisor (See 09-17-26 SUNVISOR REMOVAL/INSTALLATION.)
(16)Assist handle (See 09-17-27 ASSIST HANDLE REMOVAL/INSTALLATION.)
4. Disconnect the rear washer hose.
5. Disconnect the roof harness connector.
CENTER ADAPTER
acxuuw00000675
ASSIST HANDLE
ASSIST HANDLE COVER
A6E7746W001
ASSIST
HANDLE
C6U0917W102
INTERIOR TRIM
09-17–28
6. Remove the fasteners.
7. Remove the sunroof seaming welt (vehicles with
sunroof only)
8. Take the headliner out from the opened liftgate.
9. Install in the reverse order of removal.
End Of Sie
WM: FLOOR COVERING
FLOOR COVERING REMOVAL/INSTALLATION
id091700803000
1. Disconnect the negative battery cable.
2. Remove the following parts:
(1) Front seat (See 09-13-2 FRONT SEAT REMOVAL/INSTALLATION.)
(2) Rear seat (See 09-13-7 REAR SEAT REMOVAL/INSTALLATION.)
(3) Joint cover (See 06-14-6 STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION.)
(4) Front scuff plate inner (See 09-17-19 FRONT SCUFF PLATE REMOVAL/INSTALLATION.)
(5) Rear scuff plate inner (See 09-17-19 REAR SCUFF PLATE REMOVAL/INSTALLATION.)
(6) Front side trim (See 09-17-18 FRONT SIDE TRIM REMOVAL/INSTALLATION.)
(7) Console panel (See 09-17-13 CONSOLE REMOVAL/INSTALLATION.)
(8) Console (See 09-17-13 CONSOLE REMOVAL/INSTALLATION.)
(9) B-pillar lower trim (See 09-17-16 B-PILLAR LOWER TRIM REMOVAL/INSTALLATION.)
(10)Sub trunk box (See 09-17-25 SUB TRUNK BOX REMOVAL/INSTALLATION.)
(11)Trunk end trim (See 09-17-24 TRUNK END TRIM REMOVAL/INSTALLATION.)
(12)Trunk side trim (See 09-17-25 LIFTGATE SIDE TRIM REMOVAL/INSTALLATION.)
(13)Selector lever component. (See 05-18-7 SELECTOR LEVER COMPONENT REMOVAL/INSTALLATION.)
(14)Selector lever component bracket.
(15)SAS control module. (See 08-10-10 SAS CONTROL MODULE REMOVAL/INSTALLATION.)
(16)Console bracket.
3. Cut away the floor covering as shown in the
figure.
Note
• The cut part does not need to match up
when installing the floor covering.
FASTENER
RETAINER
REAR WASHER HOSE
ROOF HARNESS
HEADLINER
acxuuw00000673
acxuuw00001830
FLOOR COVERING
CUT LOCATION
acxuuw00001550
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст