Mazda CX 7. Manual — part 190
PROPELLER SHAFT
03-15–3
03-15
PROPELLER SHAFT REMOVAL/INSTALLATION
id031500800300
1. Remove the negative battery cable.
2. Remove the middle pipe, and front pipe. (See 01-15-2 EXHAUST SYSTEM REMOVAL/INSTALLATION[L3
WITH TC].)
3. Remove in the order indicated in the figure.
4. Install in the reverse order of removal.
.
7
6
8
9
1
1
17.6—26.4 {1.8—2.6, 13—19}
N·m {kgf·m, ft·lbf}
17.6—26.4 {1.8—2.6, 13—19}
37.3—52.0
{3.9—5.3,
28—38}
37.3—52.0 {3.9—5.3, 28—38}
49.0—58.0 {5.0—5.9, 37—42}
49.0—58.0 {5.0—5.9, 37—42}
2
3
7
4
4
5
acxuuw00000570
1
Balk head plate
2
Bolt
(See03-15-4 Bolt and Nut Removal Note.)
3
Nut
4
Bush, spacer
5
Bracket
6
Nut
7
Bush, spacer
8
Nut
(See03-15-4 Bolt and Nut Removal Note.)
9
Propeller shaft
(See03-15-4 Propeller Shaft Installation Note.)
1871-1U-06B(03-15).fm 3 ページ 2006年3月15日 水曜日 午前11時8分
PROPELLER SHAFT
03-15–4
Bolt and Nut Removal Note
Caution
• Do not mark with a punch to prevent imbalance.
1. Before removing the nut, place alignment marks
on the companion flange (front) and constant
velocity joint, and on the companion flange (rear)
and yoke.
Propeller Shaft Installation Note
1. Align the alignment marks and install the propeller
shaft.
2. When installing a new propeller shaft, align the
rear differential companion flange mark with the
tag on the propeller shaft so that they are at the
nearest position, and assemble.
3. Perform a road test and verify that there is no
abnormal vibration or noise.
End Of Sie
FRONT
REAR
acxuuw00001383
FRONT
REAR
acxuuw00001383
TAG
MARKING
acxuuw00000572
1871-1U-06B(03-15).fm 4 ページ 2006年3月15日 水曜日 午前11時8分
PROPELLER SHAFT
03-15–5
03-15
PROPELLER SHAFT INSPECTION
id031500800500
1. Measure the propeller shaft center runout using
the dial gauge.
• If it exceeds the maximum specification,
replace the propeller shaft as a single
component.
Maximum propeller shaft runout
0.8 mm {0.031 in}
2. Inspect the play and rotation of the joint by turning
the universal joint in the directions shown by the
arrows.
• If it is not within the specification, replace the
propeller shaft.
Propeller shaft starting torque
0.29— 1.47 N·m {3.0— 14.9 kgf·cm, 2.6—
13.0 in·lbf}
End Of Sie
acxuuw00000573
ampjjw00002749
1871-1U-06B(03-15).fm 5 ページ 2006年3月15日 水曜日 午前11時8分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст